InFocus Projector In102 User Manual

Operation 21
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your preferred language first.
1. Press MENU/EXIT on the projector or 
remote control to turn the OSD menu 
on.3. Press  to highlight 
Language and press  /  
to select a preferred 
language.
2. Use  /  to highlight the SYSTEM 
SETUP: Basic menu.4. Press MENU/EXIT twice* on 
the projector or...

Operation 22
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes 
an option for setting up password security. The password can be set through the 
On-Screen Display (OSD) menu. For details of the OSD menu operation, please 
refer to Using the menus on page 21.
You will be inconvenienced if you activate the password functionality and subsequently forget 
the password. Print this reference guide (if necessary) and write the password you used in...

Operation 23
Entering the password recall procedure
1. Press and hold AUTO on the projector or 
remote control for 3 seconds. The projector 
will display a coded number on the screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local service center to 
decode the number. You may be required to 
provide proof of purchase documentation to 
verify that you are an authorized user of the 
projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP:...

Operation 24your retry. You can press MENU/EXIT to cancel the change or try 
another password.
Though the password function is disabled, you need to keep the old password on hand should 
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it 
can only display one full screen at a time. 
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the 
default of...

Operation 25
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. 
These adjusters change the image height and projection angle. To adjust the 
projector:
1. Press the quick-release button and lift the 
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster foot to fine tune 
the horizontal angle.
To...

Operation 26
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that you 
need using the zoom ring.
2. Then sharpen the image by rotating the focus 
ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at 
either the top or bottom. It occurs when the projector is not perpendicular to the 
screen. 
Besides adjusting the height of the projector, you may need to follow one of these 
steps:
 Using the remote control
Press  /...

Operation 27
Magnifying and searching for details
If you need to look at specific details on the projected picture, magnify the picture. 
Use the direction arrow keys for navigating the picture.
 Using the remote control
1. Press Digital Zoom +/- to display the 
Zoom bar.
2. Press Digital Zoom + to magnify the 
center of the picture. Press the key 
repeatedly until the picture size is suitable 
for your need.
3. Use the directional arrows ( ,  ,  ,  ) 
on the projector or remote control to 
navigate the...

Operation 283. Press  /  to select an aspect ratio to suit the format of the video signal and 
your display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the 
projectors native resolution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make...

Operation 29
Optimizing the image
Selecting a picture mode
The projector is preset with several 
predefined picture modes so that you can 
choose one to suit your operating 
environment and input signal picture type.
To select an operation mode that suits your 
need, you can follow one of the following 
steps.
 Press MODE/ENTER on the remote 
control or projector repeatedly until your desired mode is selected.
 Go to the PICTURE > Preset Mode menu and press  /  to select a desired 
mode.
Setting the...

Operation 30
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted 
wall which may not be white, the Wall Color feature can help correct the projected 
picture’s color to prevent possible color difference between the source and 
projected pictures.
To use this function, go to the DISPLAY > Wall Color menu and press  /  to 
select a color which is the closest to the color of the projection surface. There are 
several precalibrated colors to choose from: Light...