InFocus Projector IN100 User Manual

							30
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must 
 be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS: •Turn the 

projector off and unplug power cord before cleaning any part of 
the projector.
• Do not touch or block the projector lens with any objects as this can 
damage the projector lens. Scratches,  gouges and other lens damage are not 
covered by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing 
covers may expose you to dangerous voltage and other hazards. Refer all 
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock for instructions on how to use it.
security 
lock 
						

							31
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the 
lamp has been in use. Twenty hours before the lamp life expires, the message 
“Replace lamp” appears on the screen at startup.
•NOTE : Be sure to use the InFocus lamp module designed for this projector. 
You can order new lamps from  www.infocus.com (in select areas), your 
retailer or your dealer.  Only genuine InFocus lamps are tested for use in this 
projector.  Use of non InFocus lamps may cause electrical shock and fire, and 
may void the projector warranty.  InFocus is not liable for the performance, 
safety or certification of any other lamps.
WARNINGS :
• The projector uses a high-pressure mercury glass lamp.  The lamp may fail  prematurely, or i
 t may rupture with a po pping sound if jolted, scratched, or 
handled while hot.  The risk of lamp failure or rupture also increases as the 
lamp age increases; please replace the lamp when you see the “Replace Lamp” 
message.
• To avoid burns, allow the projector to cool for at least 60 minutes before you  replace the lamp.
• Do not touch or block the projector lens with any objects as this can damage  the projector lens. Scratches, gouges and other lens damage are not covered 
by the product warranty. 
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure  projection sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event  that the lamp ruptures, small glass fragments may be generated. The lamp 
module is designed to contain most of these fragments, but use caution when 
removing it. 
• Before replacing a ruptured lamp, clea n the lamp compartment and dispose of 
cleaning materials. Wash hands after lamp replacement. 
• When replacing the lamp while the projector is ceiling-mounted, wear  protective eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage  in accordance with local disposal 
laws. See  www.lamprecycle.org . 
						

							32
1
Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, located on top of the projector, by removing the 
screw on the side of the lamp door, sliding the door forward, and lifting the 
lamp door off.
4Loosen the captive screws that attach the lamp housing to the projector. 
 
NOTE : 
If the projector is installed on a ceiling mount, be careful not to drop 
the lamp module once the captive screws are loosened.
5Carefully lift the lamp straight up, off of the alignment pins; being careful not to 
pinch the lamp connector. Dispose of the lamp in an environmentally proper 
manner.
6Install the new lamp module, aligning the pins properly. Be careful not to pinch 
the lamp connector.
7Tighten the screws. (NOTE : If the pins have not been aligned properly, the 
screws will not tighten securely.)
8Replace the lamp door by (a) aligning the hinges, (b) putting the lamp door 
down and (c) locking it back into place.
9Replace the lamp door sc rew and tighten securely.
10Plug in the power cord and press the Power button to turn the projector back 
on.
11To reset the lamp hour timer, navigate to the  Advanced Menu > Status/Service 
menu and select  Reset Lamp Hours... .
turn off and unplug 
projector wait 60 minutes
loosen screws
Image
Setup
Status/Service
Basic MenuSource Info...
Projector Info...
Reset Lamp Hours...
Factory Reset...
Service Code...
( Advanced Menu )MDL: IN112
FW: 0.13 
						

							33
INDEX
Numerics
3D Sync Invert 26
A
Aspect Ratio 25
Audio In Computer connector 7
Auto Image 25
Auto Off Time 29
Auto Source 28
AV Mute 27
B
Blank Key 27
Blank Screen 27
Brightness 25
C
Cable box 10
Ceiling Mount 27
Closed Captions 27
Color Space 26
Computer In connector 7
Connecting
Video device 10
Contacting InFocus 18
Contrast 25
Customer service contact information 18
D
Detect Film 26
Digital Zoom 27
F
Factory Reset 29
Focus 9
Force wide 26
Freeze Screen 27
G
Gamma 26
H
HDTV 25
High Altitude Setting 29
Horizontal Position 26
Horz Shift 27
I
Internal Speaker 27
K
Keypad 27
Keypad buttons 21
Keystone 25
L
Lamp Low Power 28
M
Magnify Level 27
Menu Transparency 28
menu usage 24
Mute 27
O
Overscan 26, 27
P
Phase 26
PIN Protect 28
Power connector 7
Power cord 7
Power Saving Mode 28
Prevent PC Screen Saver 26
Programmed Dimming 28
Projector Connecting video devices 10
Keypad buttons 21
Menus 24
Positioning 6
Setting up 6
Troubleshooting problems 11
Projector Info 27, 29 
						

							34
R
Rear Project 27
Red/Green/Blue Gain 26
Red/Green/Blue Offset 26
remote control 19
Resetting the projector 29
S
Screen Aspect 10
Search Screen 28
Service 29
Set Black Level... 26
Sharpness 25
Show Messages 28
Source 27
Source Info 27, 29
Sync Threshold 26
T
Tint 26
Tracking 26
Troubleshooting 11
TV tuner 10
U
USB 5
V
Vert Shift 27
Vertical Position 26
Volume 25
Volume button 20
W
Warranty 18
Z
zoom 9