InFocus Projector IN10 User Manual
Here you can view all the pages of manual InFocus Projector IN10 User Manual. The InFocus manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 1
IN10 Reference Guide
Page 2
1
Declaration of ConformityManufacturer: InFocus Corporation, 27500 SW Parkway Avenue, Wilsonville,
Oregon 97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: IEC 60950-1: 1
st...
Page 3
2 Table of Contents Introduction 3 Connecting a computer 5 Required computer connections 5 Displaying a computer image 6 Adjusting the image 7 Connecting a video device 8 Shutting down the projector 9 Troubleshooting your setup 9 Using the keypad buttons 16 Using the remote control 17 Optimizing computer images 18 Presentation features 18 Optimizing video images 18 Customizing the projector 18 Using the menus 19 Picture menu 20 Settings menu 23 Maintenance 26 Cleaning the lens 26...
Page 4
3 IntroductionYour new XGA 1024x768 resolution digital projector is specifically designed for portability, connectivity, and collaboration. It is easy to connect, easy to use, easy to transport, and easy to maintain Product specificationsTo read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com, as specifications are subject to change. AccessoriesThe standard accessories that came with your projector are listed in the included user ’s guide....
Page 5
4 Connector PanelThe projector provides computer and video connectors: one M1-D/A (HD, DVI, and computer) one S-video one composite RCA videoone audio inConnector panel Audio inS-video Composite videoComputer
Page 6
5 Connecting a computerRequired computer connectionsConnect the black end of the computer cable to the Computer connector on the projector. Connect the blue end to the video port on your computer. If you are using a desktop computer, you first need to disconnect the monitor cable from the computer ’s video port. Some Macintosh® computers do not have a standard VESA-out video port. If the supplied computer cable will not connect to your computer, purchase the appropriate adapter from your Apple®...
Page 7
6
Displaying a computer image Remove the lens cap.
Press the Pow e r button on the top of the projector or the remote.The LED blinks green and the fans start to run. When the lamp comes on,
the start up screen displays and the Power light is steady green. It can take a
minute for the image to achieve full brightness.
? No startup screen? Get help on
page
9.
Turn on your computer.The computer ’s image should appear on the projection screen. If it doesn’t,
press the Source button. Make sure...
Page 8
7 Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but - ton to extend the elevator foot. Rotate the leveling foot (located at the bottom back left corner), if necessary. Position the projector the desired distance from the screen, so that the lens is perpendicular to the screen. See page 29 for a table listing screen sizes and distances. Adjust the zoom or focus rings by rotating them until the desired image size and focus are produced. If the...
Page 9
8 Connecting a video device If your video device uses a round, four-prong S-video connector, plug the S-video cable into the S-video Out connector on the video device and into the Video 1 connector on the projector. If the device uses a composite video connector, plug the composite video cable into the Composite Out connec - tor on the video device and into the Video 2 connector on the projector. For audio, plug a mini-plug audio Y-cable into the Audio in connector on the projector and into the...
Page 10
9 Shutting down the projectorThe projector automatically blanks the screen after no active source is detected for 30 minutes. This blank screen helps preserve the life of the pro - jector. The image returns when an active source is detected or a remote or keypad button is pressed. Screen SaveYou can make the blank screen appear after five minutes by turning on Screen Save in the Settings>System menu. See page 24. There are six time options for the Screen Save feature. They range from five minutes...