InFocus Projector CP-x443 User Manual

31

Multifunctional settings
VIDEO Qlty. Menu
With the VIDEO Qlty. menu, items shown in the table below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
ItemDescription
PROGRESSIVE
Using the buttons ▲/▼ switches the progressive mode.
TV FILM TURN OFF   
• This function performs...

32

Multifunctional settings
INPUT Menu
ItemDescription
COLOR SPACE
Using the buttons ▲/▼ switches the mode for color space. 
AUTO  RGB  SMPTE240  REC709  REC601      
•This item can be selected only at a RGB signal or a component video signal(except signals of 525i(480i)/625i(576i) from the component video port).
•The AUTO mode automatically selects the optimum mode. 
•The AUTO operation may not work well at some signals. In such a case, it might be good to select the SMPTE240 or the REC709....

33

Multifunctional settings
INPUT Menu (continued)
ItemDescription
INFORMATION
Selecting this itemdisplays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMAINPUT-INFORMAINPUTTION-INFORMATION-INFORMARGB1024x768 @60.0FRAME LOCK
INPUT-INFORMAINPUT-INFORMAINPUTTION-INFORMATION-INFORMAS-VIDEOSECAMAUTO
INPUT-INFORMAINPUT-INFORMAINPUTTION-INFORMATION-INFORMACOMPONENT576i @50SCART RGB
•The “FRAME LOCK” message on the dialog means the frame lock function is...

34

Multifunctional settings
SETUP Menu
ItemDescription
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL  WHISPER
•When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL  H:INVERT  V:INVERT  H&V:INVERT
VOLUMEUsing the buttons ▲/▼ adjusts the volume.
HighLow
STEREOUsing the buttons ▲/▼ selects the internal speaker output mode.
MONO  STEREO
IR REMOTE
Select a remote sensor using the...

35

Multifunctional settings
SCREEN Menu
ItemDescription
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
SUOMI  POLSKI  TÜRKÇE
ENGLISH  FRANÇAIS  DEUTSCH ESPAÑOL ESPAÑOL ESP ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS 日本語
                 SVENSKA                
日本語
                            
MENU POSITIONUsing the buttons ◄/►/▲/▼ adjusts the menu position.To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds.
OSD...

36

Multifunctional settings
ItemDescription
START UP
Using the buttons ▲/▼ switches the mode for the start up screen.The start up screen is the screen displayed when no signal or an unsuitable signal is detected.
MyScreen  ORIGINAL  TURN OFF
    
MyScreen is the screen you can register a desired screen.ORIGINAL screen is the existing standard screen. When the TURN OFF is selected, the BLACK screen is used.
•To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to the...

37

Multifunctional settings
ItemDescription
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, the following message function works.“AUTO IN PROGRESS” while automatically adjusting”NO INPUT IS DETECTED””SYNC IS OUT OF RANGE”"Searching….” while searching for the input”Detecting….” while an input signal is detectedThe indication of the input signal by changing The indication of the aspect ration by changing
SCREEN Menu (continued) 

38

Multifunctional settings
OPTION Menu
ItemDescription
ONE TOUCH
Using the buttons ▲/▼ turns on/off the automatic  keystone correction function.
TURN ON  TURN OFF
You can automatically correct vertical keystone distortion corresponding to the angle (forward/backward tilt) at which the unit is set up. This function works with ONE TOUCH operation.• If the projection screen is inclined, or if the projector is angled downwards, it may not be possible to make the correct adjustment when V: INVERT or H&V:...

39

Multifunctional settings
ItemDescription
LAMP TIME
The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the lamp.Pressing the RESET button on the remote control or the button ► of the projector for about 3 seconds displays of the projector for about 3 seconds displays of the projectora dialog. To reset the lamp time, select the RESET using the button ▲.
RESET  CANCEL
•Please reset the lamp time only when you have replaced the lamp,for correct...

40

Multifunctional settings
NETWORK Menu
ItemDescription
DHCP
Using the buttons ▲/▼ turns on/off the DHCP function.
TURN ON  TURN OFF
If your network doesn’t support the DHCP function, select the TURN OFF.
IP ADDRESS
Enter the IP address of the projector  using Enter the IP address of the projector  using Enterthe ◄/►/▲/▼ buttons.
This menu is available only when the item of the DHCP is set to TURN OFF.
SUBNET MASK
Enter the SUBNET MASK  of your NETWORK using the ◄/►/▲/▼ buttons.
This menu is...