InFocus LP815 Projector User Manual

							9
Displaying a computer image Remove the lens cap.
Press the power switch to position “1” on the back of the projector, then 
press the Pow e r button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on, 
the startup screen is displayed and the LED is steady green. It can take a 
minute for the image to achieve full brightness. 
? No startup screen? Get help on page 17. 
Turn on your computer.
The computer ’s image should appear on the projection screen. If it doesn’t, 
press the Computer button on the projector ’s keypad. 
Make sure your laptop’s external video port is active. 
Many laptops do not automatically turn on their external video port when a 
projector is connected. Usually a key combination like FN + F5 is used to 
turn the external display on and off. Refer to your computer ’s documenta-
tion to learn your computer ’s key combination. 
? No computer image? Try pressing the Auto Image 
button on the keypad. Get help on page 17. 
remove lens cap
12
press Power switch
press Power button
I
O
turn on computeractivate laptop’s external port 
						

							10
First-time projector use with Windows 98The first time you connect a computer running Windows 98 to the projector, 
the computer recognizes the projector as “new hardware” and the Add 
New Hardware Wizard appears. Follow these instructions to use the Wiz-
ard to load the correct driver (which was installed with your Windows 
operating system).
If you are running Windows 2000, Windows ME, or Window XP, skip these 
steps and go to “Adjusting the image” on page 12.aClick Next to begin searching for the driver.bMake sure “Search for the best driver” is selected, then click Next.cUncheck any checked boxes, then click Next. Windows automatically 
locates the driver. If this driver has been removed, reload the driver using 
your Windows operating system CD.dWhen Windows finds the driver, you are ready to install it. Click Next.
abcd 
						

							11
Skip this page if you did not connect a USB mouse cable
For Windows 98:
 If you connected the USB cable, the Add New Hardware Wizard 
appears again. Drivers must be installed to use the USB functionality. 
The Wizard launches two times. 
The first time it detects a USB Human Interface Device (for the key-
board). 
The second time it detects a USB Human Interface Device (for the 
mouse). 
For Windows 2000, Windows ME, and Windows XP:
 The USB drivers are automatically installed.  
						

							12
Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but-
ton to extend the elevator foot. 
Rotate the leveling foot (located at the bottom back right corner), if neces-
sary.
Position the projector the desired distance from the screen at a 90 degree 
angle to the screen. 
See page 42 for a table listing screen sizes and distances.
Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
If the image is not square, adjust the vertical digital keystone by using the 
buttons on the keypad. 
Press the upper Ke y s t o n e  button to reduce the upper part of the image, and 
press the lower Ke y s t o n e  button to reduce the lower part.
You can also adjust the horizontal keystone via the menus. See page 30.
Adjust the Contrast or Brightness in the Picture menu. 
See page 29 for help with the menus.
adjust height
rotate level-
ing foot
elevatorfoot
adjust distanceadjust zoom and focus
focus
zoom
adjust keystone
adjust Contrast or Brightness
contrast
brightness 
						

							13
Connecting a video device Standard video connectionsPlug the audio/video (A/V) cable’s yellow connector into the video-out 
connector on the video device. Plug the other yellow connector into the yel-
low Video 2 connector on the projector. 
Plug a white connector into the left audio out connector on the video device 
and plug a red connector into the right audio out connector on the video 
device. Plug the remaining white connector into the left audio in connector 
on the projector (to the right of the yellow Video 2 connector), and plug the 
red connector into the right audio in connector on the projector.
Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet. 
NOTE: Always use the power cable that shipped with the projector.Optional video connectionsIf the video device uses a round, four-prong S-video connector, plug an 
S-video cable (sold separately) into the S-video connector on the video 
device and into the Video 1 connector on the projector. Use the A/V cable’s 
audio connectors as described directly above (the yellow connectors on the 
A/V cable are not used).
If the video device uses component cable connectors (sold separately), plug 
the cable’s green connectors into the green component-out connector on the 
video device and into the green component connector (labeled “Y”) on the 
projector. Plug the component cable’s blue connectors into the blue compo-
nent-out connector on the video device and into the blue component con-
nector (labeled “Pb”) on the projector. Plug the component cable’s red 
connectors into the red component-out connector on the video device and 
into the red component connector (labeled “Pr”) on the projector. If you are 
using RGB input, plug the additional connector into the Video 2/Synch con-
nector and turn on the RGB Video option in the Sources menu. See page 33. 
To connect a progressive scan EdTV or HD component source, use the Com-
ponent to VESA adapter to connect the source.
connect A/V cable
computer 2
network
audio inLcomputer in
trigger
monitor out
serial control
R audio in
computer 1
USBmouse
computer 3
connect power cable
computer 2
network
audio inLcomputer in
trigger
monitor outserial control
R audio incomputer 1USBmouse
computer 3
I
O
connect S-video and video cables
computer 2
network
audio inLcomputer in
trigger
monitor outserial control
R audio incomputer 1USBmouse
computer 3
I
O
connect component cables
I
O
computer 2
network
audio inLcomputer in
trigger
monitor outserial control
R audio incomputer 1USBmouse
computer 3
and video cables
computer 2
network
audio inLcomputer in
trigger
monitor outserial control
R audio incomputer 1USBmouse
computer 3VESA adapter component to  
						

							14
Displaying a video imageRemove the lens cap. 
Press the power switch to position “1” on the back of the projector, then 
press the Powe r button on the top of the projector.
The LED flashes green and the fans start to run. When the lamp comes on, 
the startup screen is displayed and the LED is steady green. It can take a 
minute for the image to achieve full brightness. 
? No startup screen? Get help on page 16.
Plug in and turn on the video device.
The video device’s image should appear on the projection screen. If it 
doesn’t, press the Video button on the keypad. 
Adjust the height of the projector by pressing the release button to extend 
the elevator foot. Rotate the leveling foot, if necessary. 
Position the projector the desired distance from the screen at a 90 degree 
angle to the screen. See page 42 for a table listing screen sizes and distances 
to the screen.
remove lens cappress Power switch
press Power button
I
O
12
turn on video deviceadjust height
rotate
leveling 
foot
elevatorfoot
adjust distance 
						

							15
Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
If the image is not square, adjust the vertical keystone using the buttons on 
the keypad. Press the upper Key s t o n e  button to reduce the upper part of 
the image, and press the lower Key s t o n e  button to reduce the lower part.
You can also adjust the horizontal keystone via the menus. See page 30.
Adjust the volume on the keypad or remote.
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu. 
See page 29 for help with the menus.
adjust zoom and focus
focus
zoom
adjust keystone
adjust volumeadjust Picture menu 
						

							16
Shutting down the projectorThe projector automatically blanks the screen after no active source is 
detected for 30 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or 
keypad button is pressed.
Screen Save
You can make the blank screen appear after five minutes by turning on 
Screen Save in the Settings>System menu. See page 34.
Pow e r  S av e
The projector also has a Power Save feature that automatically turns the 
lamp off after no signals are detected for 5 minutes. After 3 additional min-
utes with no signal, the projector powers down. If an active signal is 
received before the projector powers down, the image is displayed. You 
must press the Power button to display an image after 30 minutes have 
passed. When Power Save is enabled, Screen Save is disabled. See page 34.
Turning off the projector
To turn off the projector, press the power button and verify that you want to 
turn the projector off by pressing the power button again within 3 seconds. 
You can cancel the shutdown by not pressing the power button a second 
time. The lamp turns off and the LED blinks green for 1 minute while the 
fans continue to run to cool the lamp. When the lamp has cooled, the LED 
lights green and the fans stop. Press the power switch on the back of the 
projector and unplug the power cable to completely power off the projector.
Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section 
(page 25). If it does not, troubleshoot the setup. The Interactive Display and 
LED on top of the projector indicate the state of the projector and can help 
you troubleshoot. 
 
The following tables show common problems. In some cases, more than one 
possible solution is provided. Try the solutions in the order they are pre-
sented. When the problem is solved, you can skip the additional solutions.
Table 1: LED behavior and meaning
LED color/behavior
Meaning
solid green The projector is plugged in and the power 
switch is in the On position, or the projec-
tor has been powered on and the soft-
ware has initialized. The projector has 
been turned off and the fans have stopped.
blinking green The power button has been pressed and 
the software is initializing, or the projec-
tor is powering down and the fans are 
running to cool the lamp.
blinking red
see page 42 for more informationA fan or lamp failure has occurred. Make 
sure the vents aren’t blocked (see 
page 22).Turn off the projector and wait 
one minute, then turn the projector on 
again. If the Replace Lamp message 
appears, replace the lamp and reset the 
lamp timer. Contact Technical Support if 
the problem persists
.
solid red An unidentifiable error : please contact 
Technical Support. 
						

							17
Source Troubleshooting
Problem Solution Result
No startup screenPlug power cable in, press power switch,
press power button. Remove lens cap.
Correct image
Only startup screen appears
Press the Computer button 
Activate laptop’s external portComputer image projected
1
2
3
startup
screen
startup
screen
A
or restart
laptop
A
A 
						

							18
No computer image, just the words “Signal out of 
range” Adjust computer refresh rate in Control 
Panel>Display>Settings>Advanced>
Adapter (location varies by operating 
system)Computer image projected
Only my laptop’s background appears, not the 
Desktop icons Disable “Extend my Windows Desktop” in 
Control Panel>Display>Settings>Display 2 
(location varies by operating system)Background and Desktop projected
Signal out of
range
A
You may also need to set a different 
resolution on your computer, as shown
in the problem, “Image fuzzy
or cropped”
A
A
A
A
 
Uncheck this
option, then
click Apply
A
A