InFocus LP1200 Projector User Manual

							31
ENGLISH
Recording the image (For Windows)
When you wish to record the image of the display to a
PC-CARD.
1. Cooose the PC-CARD drive using the drive bar
under the status bar.9. Click the return button.
The presentation window will open. The recorded
image appears on the presentation window.
¥ Depending on the personal computer, the recorded
image can appear incorrectly. In this case, set the
delay time longer by using the Capture setting
dialog box.
10.Choose [Save presentation...] under the [File]
menu.
¥ A presentetion which has been recorded
already, Select ÒSave As...Ó to asve as.
11.Choose [Exit] under the [File] menu to quit from
PCV.
When you wish to record the image from existing files.
1. Cooose the PC-CARD drive using the drive bar
under the status bar.
¥ If you are using Windows 3.1, select ÔSelect card
driveÔ in Option menu of PCV main wimdow.
2. Choose [
New presentation...] under the [File]
menu.
The new presentation window will open.
3. Choose [Add image] under the [Image] menu and
then choose [Image file...].
¥ If you are using Windows 3.1, select ÔOpen
image fileÔ in File menu of PCV main wimdow.
4. Select the image you wish to record.
5. Click OK button.
The recorded image appears on the presentation
window.
¥ The maximum number of group (presentation)
that can be recorded to a PC card is 160.
¥ The maximum number of the images that can be
recorded to a group is 99.
6. Repeat steps 3 to 5 for other images.
7. Choose [
Save presentation...] under the [File]
menu.
8. Choose [E
xit] under the [File] menu to quit from
PCV.
Drive bar
¥ If you are using Windows 3.1, select ÔSelect card
driveÔ in Option menu of PCV main wimdow.
2. Choose [
New presentation...] under the [File]
menu.
The new presentation window will open.
3. Choose [Add image] under the [Image] menu and
then choose [Screen 
capture...].
¥ The PCV windows disappear and the capture
dialog box appears.
Capture setting buttton
Return button
Capture button
¥ If you are using Windows 3.1, select ÔImage
capture...Ô in TOOL of PCV main wimdow.
4. Display the image you wish to record on the
screen.
5. Click the capture button.
The Compress setting window appears.
6. Select the compress type.
¥ You can confirm the compressed image by
clicking the Preview button.
¥ If the command [Preserving the setting] is
checked , you donÕt need to set the style of save
by each images (Not Windows 3.1).
7. Click OK button.
8. Repeat steps 4 to 7 for other images. 
						

							32
ENGLISH
Editing the presentation (For Windows)
Delete the image
1. Select the image to be deleted.
2. Choose [
Delete image...] under the [Image] menu.
¥ If you are using Windows 3.1, choose [
Delete
image...] under the [
Tool] menu.
Sequencing
A. Exchange images
You can exchange the images among images next to
each other.
1. Select an image to be exchanged.
2. Drag the image and drop on the next or previous
image.
Advanced feature with PC (Continue)
Preview an image
1. Double click the image.
The preview image appears on the displays.
2. Click the image by using the left button of the
mouse.
{
Display image information
1. Choose [Image information] under the [Image]
menu.
The image information window appears.
¥ If you are using Windows 3.1, choose click the
image by using the right button of the mouse.
B. Move images
You can move images to another position.
1. Select an image to be moved.
2. Drag the image and drop it on the other image
(except next or previous image).
The image will be moved to the previous position
of the dropped image.
{
2. Choose OK to close the image information window.
How to save a file which has been made
by a presentation software (For
Windows 95 only)
1. Make up a presentation by the presentation
software.
2. Choose [Print] under the [File] menu.
3. Set to PCV driver for printing name.
¥ PCV drive will automatically be installed in
the system of the personal computer when PCV
is installed. 
						

							33
ENGLISH
4. Click the properties button.Starting up PCV (For Macintosh)
1. Start up Macintosh.
2. Insert the PC card to the PC Card slot on the per-
sonal computer.
3. Double click the [PCV for Mac] icon.
Command reference
The command references are as shown below:
File
Create New presentation .Create a new presentation.
Open presentation... Opens an existing presenta-
tion.
Close presentation ...Closes an opened presenta-
tion.
Save presentation .... Saves an opened presentation
using the same name.
Delete presentation .Delete an opened presenta-
tion.
Open image file... ..... Import an image from a file.
Done ......................... Exits PCV.
Edit
Cut ............................Deletes selected image from
the presentation and moves it
to the clipboard.
Copy .......................... Copies selected image data
from the presentation to the
clipboard.
Paste .........................Pastesimage data from the
clipboard into the presenta-
tion.
Clear... ......................Deletes the selected image
from an opened presentation.
Option
Preference... ............. Select the format BMP or
JPEG.
Get Screen Shot Image ....Captures screen and inserts it
to a presentation.
Recording the image (For Macintosh)
When you wish to record the image of the display to a
PC-CARD.
1. Display the image you wish to record on the
screen.
2. Press the shift button, command button and
number 3 button simultaneously.
3. Repeat steps 1 and 2 for other images.
4. Choose [Get Screen Shot Image] under the [Op-
tion] menu.
The presentation window will open. The recorded
image appears on the presentation window..
¥ The file type to be recorded are BMP or JPEG. To
change file type, select [Preference] under the
[Option] menu then change setting. Reboot PCV.
5. Choose [Save presentation...] under the [File]
menu.
6. Choose [Done] under the [File] menu to quit from
PCV.
5. If necessary, set the Resolution, Expand, File
Format or JPEG Quality.
6. Click OK button on the PCV driver Properties
dialog box.
7. Click OK button.
8. Cooose the PC-CARD drive.
9. Click OK button.
¥ The presentation data will be saved as PCVdrv
on PC card.
¥ PCVdrv is a temporaly file. If you record
presentation continuously ,The previous data
will be erased. Please follow as below to re-
name the file.
10.Boot up PCVÕs programme.
11.Choose [Open presentation...] under the [File]
menu.
12.Select PCVdrv file
The presentation window will openand.  The
recorded image appears on the presentation
window.
13.Choose [Save presentation As...] under the [File]
menu.
14.Choose [Exit] under the [File] menu to quit from
PCV. 
						

							34
ENGLISH
When you wish to record the image from existing files.
1. Choose [Create New presentation...] under the
[
File] menu.
The new presentation window will open.
2. Select ÔOpen image fileÔ in File menu of PCV main
wimdow.
3. Select the image you wish to record.
4. Click OK button.
The recorded image appears on the presentation
window.
5. Choose [Save presentation...] under the [File]
menu.
6. Choose [Done] under the [File] menu to quit from
PCV.
Editing the presentation (For Macintosh)
Delete the image
1. Select the image to be deleted.
2. Choose [Clear] under the [File] menu.
Sequencing
A. Exchange images
You can exchange the images among images next to
each other.
1. Select an image to be exchanged.
2. Drag the image and drop on the next or previous
image.
Advanced feature with PC (Continue)
{
B. Move images
You can move images to another position.
1. Select an image to be moved.
2. Drag the image and drop it on the other image
(except next or previous image).
The image will be moved to the previous position
of the dropped image.
{
Preview an image
1. Select an image to be previewed.
2. Double click the image.
The preview image appears on the displays. 
						

							35
ENGLISH
B. PCGC (Personal Computer Graphic Control)
By connecting to personal computer is RS-232C port, you can operate your computer with the projector remote
control. Also you can set the menu setting of the projector by computer.
Connection
Projector + IBM PC or IBM PC compatibles (DOS/V)
Note: If the only serial port is a Òmodem/printerÓ, use it.
Projector + NEC PC 98 series
RS-232C cable to Com1 
Comportto RS-232C 1
IN terminal
Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector,
a 25-pin serial port adapter is required. Contact your dealer for details.
RS-232C cable  RS-232C adapter 
for Macintosh
to modem port
or printer port to RS-232C 1
IN terminal
Projector + Macintosh
RS-232C cable  RS-232C
adapter for NEC
(option)
to RS-232C terminalto RS-232C 1
IN terminal 
						

							36
ENGLISH
Installation of software
For Windows 95
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Start up Program Manager.
Click the [Start] button and select the [Run (
R)] com-
mand. Then the [Run] dialog box is displayed.
4. If you inserted the CD-ROM to drive D, type [D:
Win95\Pcgc\Us\Setup] in the command line text
box and click the OK button. The letter [D] may be
different according to the drive you use.
5. When the setup program starts up, follow the on-
screen instructions.
6. When the message ÒCompletedÓ appears on screen,
click the [Finish] button to complete the installation.
For  Windows 3.1
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Select the [Run (
R)] command on the icon menu so
that the dialog box [Run] is displayed.
4. If you inserted the CD-ROM to drive D, type
[D:Win31\Pcgc\Us\Setup] in the command line
text box and click the OK button. The letter [D]
may be different according to the drive you use.
5. When the setup program starts up, follow the on-
screen instructions.
6. When the message ÒcompletedÓ appears on screen,
click the [OK] button to complete the installation.
For Macintosh
1.  Start up Macintosh.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3.  Copy PCGCÓ file in the ÒUSÓ folder of the
ÒPCGCÓ folder to anywhere on the hard disk.
Starting up PCGC
Double click the [PCGC] icon in the setup folder to
start up PCGC.
¥ Do not use SpacePointer during the PCGC opera-
tion.
Note:
¥ When you operate the PCGC, do not use
SpacePointer.
¥ Make sure proper connection shave been made, or
else the PCGC will not start up.
¥ When you operate the PCGC, switch off the menu
display on the projector.
When you operate the PCGC, be sure not to press
any buttons on the control panel on the projector
(except the POWER button).
Caution:
¥ InFocus is not responsible for any complications
caused by the use of this PCGC software.
For improvement, InFocus reserves the right to
change or alter any or all specification or design of
this remote control and the content of the owners
guide without any prior notice.
¥ No part of this software and owners guide may be
reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any lan-
guage in any form by any means. Otherwise, this
will be considered as a copyright infringement.
Advanced feature with PC (Continue) 
						

							37
ENGLISH
C. SpacePointer
The remote control provides remote PC operation for presentation from PC.
Connection
Projector + IBM PC or IBM PC compatibles (DOS/V)
RS-232C cable RS-232Ccable(option)
to RS-232C
terminalto RS-232C
1 terminalto RS-232C
2 terminal When connecting two personal computers 
to RS-232C
terminal
RS-232C adapter
for Macintosh
Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector,
a 25-pin serial port adapter is required. Contact your dealer for details.
Projector + Macintosh
to RS-232C
2 terminal When connecting two personal computers 
RS-232C cablePrinter cable for Macintosh (option)
RS-232C adapter
for Macintoshto modem port
or printer portto modem port
or printer port
to RS-232C
1 terminal
Note: If the only serial port is a Òmodem/printerÓ, use it.
Projector + NEC PC 98 series
RS-232C adapter
for NEC (option) RS-232C adapter
for NEC (option)
to RS-232C terminal
RS-232C cable RS-232C cable (option)
to RS-232C
1 terminalto RS-232C
2 terminal When connecting two personal computers 
to RS-232C
terminal
RS-232C adapter
for Macintosh 
						

							38
ENGLISH
Installation of software
For Windows 95
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Start up Program Manager.
Click the [Start] button and select the [Run (
R)] com-
mand. Then the [Run] dialog box is displayed.
4. If you inserted the CD-ROM to drive D, type [D:
Win95\Sp\Setup] in the command line text box
and click the OK button. The letter [D] may be
different according to the drive you use.
5. When the setup program starts up, follow the on-
screen instructions.
6. When the message ÒCompletedÓ appears on screen,
click the [Finish] button to complete the installation.
For  Windows 3.1
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Select the [Run (
R)] command on the icon menu so
that the dialog box [Run] is displayed.
4. If you inserted the CD-ROM to drive D, type
[D:Win31\Sp\install] in the command line text
box and click the OK button. The letter [D] may
be different according to the drive you use.
5. Select the [Installation (I)] commandon the instal-
lation menu.
6. When the setup program starts up, follow the on-
screen instructions.
7. When the message ÒcompletedÓ appears on screen,
click the [OK] button to complete the installation.
For Macintosh
1.  Start up Macintosh.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3.  Copy Alps RSSPointer file in the ÒUSÓ folder of
the ÒSpacePointerÓ folder to the system folder.
4. Restart the Macintosh.
Operation of PC by remote control
The remote control provides remote PC operation for
presentation from PC.
1. Press the RGB button to select RGB1 or RGB2.
2. Press the START/STOP button to ON.
The operation indicator will be illuminated.
3. Confirm that the cursor of the projector does not
appear on the screen. If the cursor does appear, press
the CURSOR button to OFF.
You can use the SELECT, CANCEL and DOUBLE
CLICK button in the same way as the button on the
mouse. You can also move the cursor of PC by using
the remote control. For cursor moving, see page 25.
4. Press the START/STOP button to exit from PC
control mode.
¥ Depending on the personal computer, SpacePointer
may not work after leaving from the suspended
mode.  In this case, click the Apply button on the
control panel.  See below.
Setting of SpacePointer
For Windows
You can set the several settings in the SpacePointer
control panel in the control panel folder.
¥ Mouse cursor size and color cannot be adjusted in
the Windows 3.1.
Advanced feature with PC (Continue)
Tracking speedIf you click Fast, the cursor
moves more than twice as fast
as you move the space pointer.
When you first try the remote
control, set it to slow.
S
p
a
c
e
P
o
in
te
rSpacePointer®
Enable/Disable
SLOW
Change cursor
OKFAST Enable
ON
COM1 COM2 COM3 COM4
Disable
OFF ReceiverCheck
ConnectPort
CancelApplyHelp
Port selectionUsed to select the port connected
to the projector.
Size/colorChanges the size and color of the
mouse cursor.
Enable/Disable
For normal use set to Enable. If
you do not use SpacePointer, set
to Disable.
For Macintosh
You can set the several settings in the Alps RSSPointer
control panel in the control panel folder.
Port selectionUsed to select the port connected
to the projector.
Alps RSSPointer
ALPS  SpacePointerMonitor Size : Port :
Fast SlowHW
Modem
(W)                     (H)
1152         X        870
Tracking speedIf you click Fast, the cursor
moves more than twice as fast
as you move the space pointer.
When you first try the remote
control, set it to slow.
Monitor size
Help 
						

							39
ENGLISH
Uninstallation of software
For Windows 95
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Start up Program Manager.
Click the [Start] button and select the [Run (
R)] com-
mand. Then the [Run] dialog box is displayed.
4. If you inserted the CD-ROM to drive D, type [D:
Win95\Sp\Spuninst] in the command line text
box and click the OK button. The letter [D] may be
different according to the drive you use.
5. When the installation program starts up, follow the
on-screen instructions.
6. When the message ÒCompletedÓ appears on screen,
click the [Finish] button to complete the installation.
If  you use the  Windows 3.1
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Select the [Run (
R)] command on the icon menu so
that the dialog box [Run] is displayed.
4. If you inserted the CD-ROM to drive D, type
[D:Win31\Sp\install] in the command line text
box and click the OK button. The letter [D] may
be different according to the drive you use.
5. Select the [Uninstallation (U)] commandon the in-
stallation menu.
6. When the setup program starts up, follow the on-
screen instructions.
7. When the message ÒcompletedÓ appears on screen,
click the [OK] button to complete the uninstallation.
For Macintosh
1. Start up Macintosh.
2. Move Alps RSSPointer in the control panel folder
in the system folder to ÒTrashÓ.
3. Restart the Macintosh. 
						

							40
ENGLISH
The light source lamp is designed to project the image
on the LCD panel. When the light source lamp no longer
functions, replace it with a new one to ensure optimum
performance.
Caution:
¥ Do not remove the light source lamp from inside of
this equipment immediately after using the projec-
tor, you may get burned because of the high tem-
perature of the light source lamp.
¥ When you replace the light source lamp, press the
power button to power off, then wait for 120 sec-
onds in stand-by mode to cool down the lamp and
LCD panels. Turn off  the main switch,  unplug the
power code from the outlet and wait one hour so
that the lamp is cool to the touch.
¥ Do not remove the light source lamp except for re-
placement. Careless treatment can cause injury or
fire.
¥ Do not touch the lamp directly. It may be broken
and may cause you to injure or burn yourself.
¥ Be sure not to drop the lamp lid screw into the pro-
jector. Also be sure also not to insert metal or any
flammable objects, it may cause fire or an electric
shock. If any objects are inserted, please unplug and
contact your dealer.
¥ Install the lamp securely, failure to do so it may
cause a fire.
1. Loosen the screw of
the lamp lid on the
top cover using a
screwdriver (+) , and
remove the lid.
¥ Remove the lamp
cover in the direc-
tion of the arrow as
indicated.
Important:
Be careful not to damage the electric wire connected
to this equipment.
2. Loosen a screw (a) of fix-
ing metal using a screw-
driver (+), and remove
them.
Do not lose the fixing
metal and screws.
Replacement of a light source lamp
(a)
(e)
Fixing
metal3. Set Lamp exchanging metal into the projector.
1) Insert metal fittings for lamp replacement in
the following positions: on the front face of the
lamp (2 positions), between the lamp, and on
the bottom edges (4 positions).
2) Align screw holes (c) with node (d).
3) Fasten the piece into place using the two
screws included (b, bÕ).
Lamp exchange
metal
Hooks
(x 6)
4. Loosen the lamp fixing screw (e) using a screwdriver
(+), and remove it.
5. Hold onto the projector
by the handle as you pull
out the lamp.
For the lamp you have
removed, do not spill liq-
uid on it, place it near
flammable objects or
where children can touch
it.  Otherwise, it will cause in-
jury or fire.
6. Insert the new lamp securely
into the projector body in the
right direction.
7. Tight up the screws (e) which
have been removed in 4 using a screwdriver (+).
8. Loosen the two screws (f), (f)
of lamp exchanging metal us-
ing a screwdriver, and remove
them with the metal.
9. Remove the holes from the
lamp replacement metal
fittings (c) from the node (d).
10.Insert the fixed metal pieces
from step 2 into the screw
holes (f) and (f Õ), and use one
screw (a) to hold the piece in
place.Lamp
Handle
(f)(f)
(e)
(a)
Loosen here
(c)
(b)(b) (d)
(e)