InFocus IN72/IN74/IN76 Projector User Manual
Have a look at the manual InFocus IN72/IN74/IN76 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
20 Optimizing video imagesYour projector has been factory optimized for very good performance no matter what the source. However, if you wish to make further changes you can optimize the image using onscreen menus. For general information on using the menus, see page 21. Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu ( page 22). Select a Sharpness setting ( page 24). Use the Color Control to adjust the color gain and offset ( page 25). Adjust the Color Temperature. Select a listed value ( page 25). Turn on Overscan to remove noise on the edges of the video image ( page 25). Change the Aspect ratio ( page 22). Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9 (the projector ’s default). Choose the option that best fits your input source in the menus, or press the Resize button on the remote to cycle through the options. See page 18. Select a specific Color Space. See page 24. Select a different Video Standard. Auto tries to determine the standard of the incoming video. Select a different standard if necessary. See page 25. Make sure your DVD player is set for a 16:9 television. See your DVD player ’s user ’s guide for instructions. Customizing the projectorYou can customize the projector for your specific setup and needs. See page 26 to page 28 for details on these features. For rear projection, turn rear mode on in the Settings>System menu. For ceiling mounted projection, turn ceiling mode on in the Set - tings>System menu. Turn the projector ’s display messages on and off. Turn on power saving features. Specify blank screen colors and start up logos. Specify the language viewed on the menus. Save settings for the active source as a preset.
21 Using the menusTo open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to high - light the desired submenu, then press the Select button. To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio but - tons, or turn the feature on or off using check boxes. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, navigate to Previous or Exit, then press Select to go to the previous menu; press the Menu button at any time to close the menus. Dots appear before the menu name. The number of dots indicate menu’s level, ranging from one (the Main menu) to four (the most nested menus). The menus are grouped by usage: The Picture menu provides image adjustments. The Settings menu provides set-up type adjustments that are not changed often. The Source Info menu provides a read-only display of information about the projector and source. Certain menu items may not be visible or may be grayed depending upon a particular source being connected. Differences are also seen in analog ver - sus digital video sources and interlaced versus progressive sources. Menu options are grayed out only if the source is selected but no signal is present. For example, if the projector is set to a video source but the source, such as a DVD player, is turned off video menu options are grayed out. keypad navigation Main menubuttons Picture Settings menu menu dots Source Info menu
22 Picture menuTo adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes.Ke y s t o n e: adjusts the image vertically and makes a squarer image. Tilt the projector up or down to adjust for keystone before using the digital key - stone correction in the menu.Contrast: controls the degree of difference between the lightest and darkest parts of the picture.Brightness: changes the intensity of the image.Color: adjusts a video image from black and white to fully saturated color. Tint: adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9. The projector ’s default is 16:9. See “Choosing the aspect ratio” on page 6 for more informa - tion.Select Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox to pre - serve the 16:9 aspect ratio. If you have a 16:9 source and screen, the image fills the screen. If your source is letterboxed, the image is expanded to fill the screen. Select Natural Wide to stretch a 4:3 image to fill the entire 16:9 screen. The center two-thirds of the image is unchanged; the edges of the image are stretched.For more information regarding Aspect Ratio, see page 6. Picture menu increasing keystonedecreasing keystoneAspect ratio
23 Presets: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory Reset in the Settings>Service menu. To set a preset for the current source, adjust the image, select Save Settings in the Presets menu, then choose Save User 1, 2, or 3. You can recall these settings in the future by selecting the appropriate user presets. All settings in the Picture menu (except Keystone) are saved and recalled.Gamma : Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been specifically tuned for either film, CRT (Cathode Ray Tube), video, PC, or Bright Room input. (Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event.) White Peaking increases the brightness of whites that are near 100%.NOTE: Your viewing preferences may vary. Cycle through the gamma options and pick the one you like the best. PresetsSave User SettingsGamma
24 Advanced menuRemember that not all options in the menus are available for all sources/ signals. Phase: adjusts the horizontal phase of a computer source.Tr a c k i n g: adjusts the vertical scan of a computer source.Horizontal/Vertical Position: adjusts the position of a computer source.Sync Threshold Adjust: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, adjust this option to help it to sync when connected to the projector. Flesh Tone Correction: this modifies colors to make the skin complexion better.Film Mode: controls deinterlacing and is On by default. When checked, it assumes the incoming signal is film material and optimizes the image accordingly. Sharpness: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources, choose either REC709 or REC601 for component video sources. Advanced menu Sharpness Color Space
25 Color Temperature: changes the intensity of the colors. Select a value. Native means an uncorrected/unchanged color temperature. Other values change the white point of the colors. 6500K is generally used for film con - tent and 9300K is used for TV video.Color Control: allows you to individually adjust the gain and offset of the red, green, and blue colors. These advanced controls have the same effect as contrast and brightness, but each controls a single color only.Video Standard: when it is set to Auto, the projector attempts to automati - cally pick the video standard based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Stan - dard menu.Overscan : removes noise around the edges of the video image. Select Zoom to remove the outer 3% of the image and scale the image back up to its orig - inal size. Select Crop to remove the outer 3% of the image without rescaling the image.Noise Reduction : adjusts signal noise reduction. Choose Enable then adjust the level. The software determines the differences between successive image frames and averages the changes out to reduce the noise. Color Temperature Color Control Video StandardOverscanNoise Reduction
26 Settings menuSources: allows programming of source buttons, enables autosource, and enables the SCART RGB source. When Autosource is selected, the Source Enable feature indicates which sources the projector attempts to lock onto. You can use the Source Enable feature to eliminate certain sources from this search, which will speed the search. By default, the check boxes for all sources are checked except SCART RGB. Uncheck a source box to eliminate it from the search. When Autosource is not checked, the projector defaults to Component initially, then defaults to whatever the last active source was when the projector was powered down. To display another source, you must manually select one by pressing the Source button on the remote or keypad. This cycles through all the sources that are selected in the Source Enable menu. The Source 1, 2, and 3 menus in the Sources menu allow you to assign a source to the Source 1, 2, and 3 buttons on the remote. The Source 4 menu selection would apply to the Custom key if that option is chosen in the Cus - tom key menu, see page 27. To use the SCART RGB source, you must first select it in the Source Enable menu (the projector cannot automatically detect this source). Enabling SCART will disable Component and Composite sources.System>Rear: reverses the image so you can project from behind a translu - cent screen. Ceiling: turns the image upside down for ceiling-mounted pro - jection. Auto Ceiling: uses an internal sensor to automatically turn on ceiling mount mode if the projector is inverted. High Power: maximizes the light output of the lamp. Auto Power: When Auto Power is checked, the projector automatically goes into the startup state after the projector receives power. This allows control of ceiling mounted projectors with a wall power switch Display Messages: displays status messages (such as “Searching”) in the lower-left corner of the screen.Tr a n s l u c e n t O S D: makes the menus translucent. This prevents the image from being completely cov - ered by the menus while you are making image adjustments. Sleep Timer: automatically turns off the projector after 4 hours. Pow e r S av e: automati - cally turns the lamp off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image is displayed. Settings menu SourcesSource Enable System menu
27 Startup Logo: allows you to display a blank screen or a custom captured image (IN72 only) instead of the default screen at startup. To capture a new image, display the image and select Capture New. A mes - sage appears. Select Captured in the Startup Logo menu to display your new image. Note that this feature will not work on interlaced signals.Blank Screen : determines what color is displayed when you select Blank Screen in the Startup Logo menu and when no source is displayed. Language: allows you to select a language for the onscreen display.Custom key: allows you to assign a different function to the Custom key on the remote, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.Blank Screen: displays a solid blank image.Freeze: takes a snapshot of the projected image. If you’re watching video, the source video continues to run but the image is frozen.Source Info: the default effect. It opens a window with projector and source information.Service Info: opens the Service info window.Source 4: selects source 4 (by default, Source 4 is the Composite input). This gives you 4 direct source options on the remote. See page 26. Startup LogoBlank Screen Language menu Custom Key
28 Service: To use these features, highlight them and press Select. Factory Reset: restores all settings to their default.Reset Lamp hours: resets the lamp hours used counter in the Service Info menu to zero. Do this only after changing the lamp. Test Pattern: displays a test pattern. To display test patterns, first you must assign Blank Screen to the Custom key ( page 27), then click the Test pattern check box in the Service menu to turn the option on, exit the menus, then press the Custom button on the remote. To select the patterns, use the up/down arrows on the remote or keypad. To exit the test patterns, press the Custom button.Blue Only: turns off the Red and Green portions of the input, allowing you to properly adjust the color balance with a SMPTE color bar pat - tern.HDMI DDC: turns off the EDID extension. Some graphic cards cannot recognize the projector ’s EDID. Uncheck this box if you have trouble using HDMI or DVI sources.Service Info: provides information about the projector ’s software, serial number, and lamp.Service Code: only used by authorized service personnel. Source Info: provides information about the active source. Service menu Service Info Source Info menu
29 MaintenanceCleaning the lens1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning cloth over the lens in a circular motion. Replacing the projection lampThe lamp hours timer in the Service Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, a mes - sage appears on the screen at startup indicating that you should change the lamp. The LED on top of the projector also blinks red twice to indicate that the lamp should be changed.NOTE: You can order new lamp housings from www.infocus.com (in select areas), your retailer or your dealer. Use only a replacement lamp with the same type and rating as the original lamp.1 Turn off the projector and unplug the power cord. If ceiling mounted, disconnect all cables and detach the projector from the ceiling mount. 2 Wait 60 minutes to allow the projector to cool thoroughly. 3 Turn the projector upside down on a soft cloth so that the lamp door is facing you. Remove the base or ceiling mount plate, if attached, by removing the 3 screws. Lamp hours used wait 60 minutes turn off and unplug projector