Indesit Idl 60 Installation Manual

							9GB
Cleaning and Special Maintenance
Troubleshooting
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, let us see what can
be done first: have you forgot to press one of the buttons or to
perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on ON;
- the water supply is turned on.
 The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
  pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
 The Dishes Are Not Clean
Have you put the right amount of detergent into the dispenser?
Is the wash cycle suitable for the dishes you have placed inside the
appliance?
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Error messages.
Your dishwasher is equipped with a safety system which is able to
detect any operating anomalies. These anomalies are reported by
one or two wash cycle indicator lights G flashing rapidly.
Take a note of which lights are flashing, turn the appliance off and
call for technical assistance.Tap off alarm
If you have forgotten to turn the water tap on, your appliance will
remind you of this by sounding a few short beeps for a few minutes.
Turn the tap on and your appliance will start up again after a few
minutes. Were you to be absent when these beeps are sounded, the
appliance will be blocked automatically and indicator lights 2 and 3
(wash and rinses) will flash rapidly. Turn the appliance off at the ON-
OFF button, turn on the water tap and wait approximately 20 seconds
before turning the appliance back on; repeat the programming
operations and the selected wash cycle will start up again.
Clogged filter alarm
If the appliance is blocked and indicator lights 1 (pre-wash) and 3
(rinses)  flash rapidly, this means the filter is clogged by large particles
of food residue. Turn the appliance off, clean the filter thoroughly
and reposition it in its seat as illustrated on this page. Then turn it
back on. Repeat the programming operations and the wash cycle
will start up again.
Water load solenoid valve malfunction alarm.
If indicator light 2 (wash) flashes rapidly, TURN the dishwasher OFF
AND BACK ON AGAIN after one minute. If the alarm persists, first
turn off the water tap to avoid any flooding and then cut off the
electricity supply and call for technical assistance.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service
centre and provide them with the following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number (S/N ....),
which are indicated on the plate located on the side of the inner part
of the door.
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
Cleaning the Sprayer Arms
It may happen that food particle become encrusted on the
sprayer arms and block the holes (see Close up view
(interior), letters F-I). Check the sprayer arms periodically
and clean them when needed.
1
2
AB
C
The filter assembly
If you want consistent good results from your dishwasher,
you need to clean the filter assembly.
The food particles are removed from the wash water,
allowing it to be recirculated during the cycle, filtered
perfectly. For this reason, it is a good idea to remove the
larger food particles trapped inside the cup “C” and the
semi-circular filter A after each wash; pull the cup handle
upwards to remove them. Just rinse them under running
water.
The entire filter assembly should be cleaned thoroughly once
a month: cup C + semi-circular filter A + cylindrical filter B.
Rotate filter “B” anticlockwise to remove it.
For cleaning, use a non metallic brush.
Reassemble the filter parts (as shown in the figure) and
reinsert the whole assembly into the dishwasher. Position it
into its housing and press downwards.
The dishwasher is not to be used without filters. Improper
replacement of the filters may reduce the efficiency of the
wash and even damage your dishwasher.
 
						

							10GB
Installation
A
Positioning the Appliance
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).
Cold water connection.
This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not use a different hose. In the
event of replacements, use original spare parts only.
Connect the cold water supply hose to a 3/4 gas threaded
connection, taking care to screw it tightly onto the tap.
If the water hoses are new or have been out of use for an
extended period of time, let the water run to make sure it is
clear and free of impurities before making the connection.
If this precaution is not taken, the water inlet could get
blocked, causing damage to your dishwasher.Drain Hose Connection
Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see fi-
gure) to position it in the best
possible way. The part of the
pipe marked with the letter A
should be between 40 and
100 cm above the ground.
The pipe should not be immersed in water.
Attention: The special plastic hose support must be solidly
fastened to the wall to  prevent the drain hose from moving
and allowing water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values
for the current in the home correspond to those on the
rating plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.
Caution: the dishwasher plug must be accessible  even
when the appliance is installed as a built-in unit so that
maintenance  can be done safely.
 
						

							OM - 12/2004  -  195047911.00
 -   Xerox Business Services - DocuTech
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel  +39 0732 6611
Fax +39 0732 662501
www.merloni.com