Indesit Icd 661 Instruction Manual

							 
 
  
 19 
9. Troubleshooting Tips 
 
Before Calling for Service 
 
Review the charts on the following pages may save you from calling for service. 
 
Problem  Possible Causes  What To Do 
Fuse blown, or the circuit 
breaker tripped. Replace fuse or reset circuit breaker. Remove any other 
appliances sharing the same circuit with the dishwasher
Power supply is not 
turned on. Make sure the dishwasher is turned on and the door is 
closed securely. 
Make sure the power cord is properly plugged into the 
wall socket. 
Dishwasher doesnt 
start 
Door of dishwasher not 
properly closed. Closed dishwasher making sure that door latches. 
Kink in drain hose  Check drain hose. 
Filter clogged.  Check coarse the filter. 
(see section titled  Cleaning The Filter ) 
Technical 
problems 
Water not pumped 
form dishwasher 
Kitchen sink clogged.  Check kitchen sink to make sure it is draining well. If 
problem is kitchen sink not draining, you may need a 
plumber rather than a serviceman for dishwasher. 
Improper detergent  Use only the special dishwasher detergent to avoid 
suds. If this occurs, open the dishwasher and let suds 
evaporate. Add 1 gallon of cold water to the tub. Close 
and latch the dishwasher, then Start the  soak  wash 
cycle to drain out the water. Repeat if necessary. Suds in the tub 
Spilled rinse-aid  Always wipe up rinse-aid spills immediately. 
Stained tub interior Detergent with colourant 
was used. Make sure that the detergent is the one without 
colourant. 
White film on inside 
surface Hard water minerals  To clean the interior, use a damp sponge with 
dishwasher detergent and wear rubber gloves. Never 
use any other cleaner than dishwasher detergent for the 
risk of foaming or suds. 
The affected items are not 
corrosion resistant.  
A programme was not run 
after dishwasher salt was 
added. Traces of salt have 
got into the wash cycle. Always run the Quick wash programme . without any 
crockery in the dishwasher and without selecting the 
Turbo function (if present), after adding dishwasher salt.
General 
problems 
There are rust stains 
on cutlery 
The lid of softer is loose.  Check the lip. Ensure the fix is fine. 
Knocking noise in 
the wash cabinet The spray arm is knocking 
against an item in a 
basket. Interrupt the programme, and rearrange the items which 
are obstructing the spray arm. 
Rattling noise in the 
wash cabinet Item of crockery 
are insecure 
in the wash cabinet. Interrupt the programme, 
and rearrange the items of crockery. Noise 
Knocking noise in 
the water pipes This may be caused by on-
site installation or the 
cross-section of the piping.This has no influence on dishwasher function. if in doubt, 
contact a suitably qualified plumber. 
 
 
						

							 
 
  
 20 
 Problem  Possible Causes  What To Do 
The dishes were not 
loaded correctly. 
The programme was not 
powerful enough. 
Not enough detergent was 
dispensed. 
Item are blocking 
the path of spray arms. See notes in  Loading the Dishwasher Baskets . 
Select a more intensive programme. See Wash Cycle 
Table . 
Use more detergent, or change your detergent. 
Rearrange the items so that the spray can rotate freely.The dishes are not 
clean 
The filter combination in 
the base of wash cabinet 
is not clean or is not 
correctly fitted. This may 
cause the spray arm jets 
to get blocked. Clean and/or fit the filter combination correctly. Clean 
the spray arm jets. See Cleaning the Spray Arms. 
Cloudiness on 
glassware Combination of soft water 
and too much detergent. Use less detergent if you have soft water and select a 
shortest cycle to wash the glassware and to get them 
clean. 
Black or gray marks 
on dishes Aluminum utensils have 
rubbed against dishes. Use a mild abrasive cleaner to eliminate those marks. 
Unsatis 
factory 
washing 
result 
Detergent left in 
dispenser cups Dishes block detergent 
cups. Re-loading the dishes properly. 
Improper loading Too little 
rinse-aid Load the dishwasher as suggested in the directions. 
Increase the amount of rinse-aid/Refill the rinse-aid 
dispenser. 
Unsatis 
factory 
drying 
result 
The dishes are not 
drying 
Dishes are removed too 
soon. 
Wrong programme 
selection 
Using cutlery with a low-
quality coating Do not empty your dishwasher immediately after 
washing. Open the door slightly so that the steam can 
escape. Begin unloading the dishwasher only once the 
dishes are barely warm to the touch. Empty the low 
basket first. This prevents water form dropping off 
dishes in the upper basket. 
In short programmes the washing temperature is lower. 
This also lowers cleaning performance. Choose a 
programme with a long washing time. 
Water drainage is more difficult with these items. 
Cutlery or dishes of this type are not suitable for 
washing in the dishwasher. 
 
Error Codes 
 
When some malfunctions come on, the appliance will display error codes to warn you: 
 
Codes Meanings Possible Causes 
The dry (hase) light flicker 
fleetly Longer inlet time.  Faucets is not opened, or water intake is restricted, or 
water pressure is too low. 
The main(phase) light flicker 
fleetly Overflow.  Some element of dishwasher leaks. 
 
 WARNING! „ If overflow occurs, turn off the main water supply before calling a service.  
„ If there is water in the base pan because of an overfill or small leak, the water should be removed before restarting the dishwasher. 
 
 
						

							  
   
 21 
Technical Information 
  
 
Height: 438mm 
Width: 550mm 
Depth: 500mm 
Voltage connected Load:  see rating label 
Water pressure:  0.04-1.0MPa 
Hot water connection:  max 60°C