Indesit Dpg 15 Operation Instructions
Have a look at the manual Indesit Dpg 15 Operation Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 260 Indesit manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
//
$
$
6
0 $
0 $
0 $
+
+
0 .
0 9
0 $
0
0 @
0 .
0 $
0
0 $
0 .
0 $?
.
!33!HK2H?
9
?
?
?- %9???&
?+
6
$
6
E
)
)%
#0 >
0 8
9
5
%!
&
0 5
6E
?
6
I
%
# &
0
$.
%
# &
)
E>B
0 9
0 ? (
>34
(
#
6
2>4
0 $
-
L
-
?
8
/
!
!
/
0
Problem: Possible causes / Solutions:
The dishwasher does not start.
The plug has not been inserted into the electrical socket properly,
or there is no power in the house.
The dishwasher door has not been shut properly.
A delayed start has been programmed (see Start-up and use).
No water drains out from the
dishwasher. The dishwasher cycle has not yet finished.
The water inlet hose is bent (see Installation).
The drain duct is blocked.
The filter is clogged up with food residues.
The dishwasher makes
excessive noise. The dishes are rattling against each other or against the sprayer
arms.
An excessive amount of foam has been produced: the detergent has
not been measured out correctly or it is not suitable for use in
dishwashers (see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits. The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (see Rinse aid and salt).
The lid on the salt dispenser is not closed properly.
The rinse aid has been used up or the dosage is too low.
The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish tinge. The rinse aid dosage is too high.
The crockery has not been
dried properly. A wash cycle without a drying programme has been selected.
The rinse aid has been used up or the dosage is too low (see Rinse
aid and salt).
The rinse aid dispenser setting is not high enough.
The dishes are not clean.
The racks are overloaded (see Loading the racks).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see Wash cycles).
An excessive amount of foam has been produced: the detergent has
not been measured out correctly or it is not suitable for use in
dishwashers (see Start-up and use).
The lid on the rinse aid compartment has not been shut correctly.
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in/Tap shut-off alarm
(the Drying and End indicator
lights flash). There is no water in the mains supply.
The water inlet hose is bent (see Installation).
Turn on the tap and the appliance will start after a few m inutes.
The appliance is locked because no action was taken when the
indicator lights were flashing. Switch off the machine using the
ON/OFF button, turn on the tap and switch the machine back on
after 20 seconds by pressing the same button. Re-programme the
machine and restart the wash cycle.
Water loading solenoid valve
malfunction alarm
(The Drying indicator light flash). Switch off the appliance by pressing the ON/OFF button and switch
it back on after a minute. If the alarm continues, shut off the water
tap to eliminate the risk of flooding, remove the plug from the
electrical socket and contact Assistance.
Water inlet hose alarm/Water
inlet filter blocked. (the
W ashing, Drying and End
indicator lights flashes).
Switch off the appliance by pressing the ON/OFF button. Shut off
the water tap to eliminate the risk of flooding and remove the plug
from the electrical socket.
Make sure the water inlet filter has not becom e blocked by various
impurities. (see “Care and maintenance” chapter).