Incredible Technologies Golden Tee 99 Operation Manual

OPERATION MANUAL 

1 - Golden Tee Golf ‘99
1 GETTING STARTED .................................................................. 2
G
AME PACKAGE CONTENTS........................................................... 2
Non-Tournament Kit Version:.................................................. 2
ITS Tournament Version: ......................................................... 2
R
ECOMMENDED TOOLS AND SUPPLIES........................................... 2
Non-Tournament Kit...

Golden Tee Golf ’99 - 2
1Getting Started
Game Package Contents
Non-Tournament Kit Version:
(1) Printed Circuit Board (PCB) Assembly
(1) Connecting Wire Harness (JAMMA)
(1) Trackball Assembly w/Metal Plate
(1) Trackball Cable Assembly
(3) Button Assemblies
(1) Marquee Styrene
(1) Marquee Plexiglas
(1) Control Panel Overlay
(1) Set of Function Labels
(1) Manual
ITS Tournament Version:
(1) Golden Tee ‘99 Golf Tournament Cabinet
(1) Tournament Operation Manual
(1) Monitor Manual
(1) Bill Acceptor Manual
(1)...

3 - Golden Tee Golf ‘99
The Cabinet
Power Requirements
Make sure the game you have chosen
to convert is able to supply all the
required voltages for GOLDEN TEE
98.
+5 VDC     5 amps
+12 VDC   2 amps
WARNING!!!
The output level of many regulated switchingpower supplies actually vary with load.  Forthis reason, the power supply from an oldgame may not be correctly adjusted forGOLDEN TEE 98.  This makes the existingpower supply inappropriate and hazardous toyour new game.  Therefore, it is very importantto...

Golden Tee Golf ’99 - 4
Control Panel
Mounting the trackball correctly and securely is very
important for the profitability of your new game.
Follow these instructions carefully for mounting the
trackball to: 1) a metal control panel; 2) a wooden
control with routing; 3) or a wooden control panel
without routing.  (Refer to template inserts which came
with your new kit.)
CONTROL PANEL LAYOUT(Trackball MUST be centered on the control panel)
NOTE:
Installing the trackball  as far away from themonitor as...

5 - Golden Tee Golf ‘99
To mount trackball to a metal control
panel use Trackball Mounting
Template #1
1. Fill any existing holes in the metal control panel.
2. Place and secure TEMPLATE #1 to your control
panel in the desired location.
NOTE: 
The trackball should be as far awayfrom the monitor as possible.
3. Carefully drill the holes for the ball and the
mounting bolts using the template as a guide.
4. Remove template and file down any rough edges.
5. See Graphic Overlays section on page 6 on how to...

Golden Tee Golf ’99 - 6
To mount trackball to a wooden
control panel without routing capability
use Trackball Mounting Template #3
1. Fill any existing holes in the wooden control panel.
2. Place and secure Template #3 to your control panel
in the desired location.
NOTE: 
The trackball should be as far awayfrom the monitor as possible.
3. Carefully cut the hole for the trackball in the shape
indicated on the template.  The trackball should fit
the hole shape exactly.
4. Drill the mounting holes as...

7 - Golden Tee Golf ‘99 3. Using a sharp razor knife, trim any excess from the
background overlay. Carefully pierce through the
overlay above each control panel hole that you
have marked. Cut out material covering the pre-
drilled holes with the razor knife.  Be sure to cut
the background overlay above each hole and trim
cleanly and evenly.
Function Labels Overlay Installation
Line up the supplied function labels with the
corresponding control panel holes.  Remove the backing
and carefully press into...

Golden Tee Golf ’99 - 8
Wire Harness
WARNING!
Be sure that all power isOFF before connectingpower supply.
1. If you are installing GOLDEN TEE ‘99 into a
Dynamo cabinet with a pre-installed JAMMA
harness, you will notice that it does not have a wire
for the test switch.  You will have to add a contact
to the edge connector at the proper position
(position 15).  Some cabinets (Dynamo included)
have only one coin switch input and the coin
switches are wired together.  Connect the
designated wires to the...

9 - Golden Tee Golf ‘99 If your monitor does not have a composite SYNC input
but has separate horizontal and vertical SYNC inputs,
try connecting the composite SYNC signal from the
PCB to the negative horizontal SYNC signal on the
monitor. This should produce a satisfactory result,
although some adjustment of the monitors SYNC
controls may be necessary.
Coin Doors, Test Switch, Service Button,
and Volume Control Panel
1. Wire the coin doors and the test / service switch(es)
as per the JAMMA Harness...