Iiyama Prolite E2607ws User Manual

							
ENGLISH

 Ensure that both the computer and the monitor are switched off.
 Connect the computer to the monitor with the signal cable.
 Connect  the  monitor  to  the  audio  equipment  with  the Audio  Cable  for  computer  when  using  the 
audio features.
 Connect the Power Cable to the	monitor 	 first 	 and 	 then 	 to 	 the 	 power 	 supply.
NOTE  The  signal  cables  used  for  connecting  the  computer  and  monitor  may  vary  with  the  type  of 
computer used. An incorrect connection may cause serious damage to both the monitor and 
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. 
If  a  special  cable  is  required  please  contact  your  local  iiyama  dealer  or  regional  iiyama 
office.
  For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama 
office 	 for 	 a 	 suitable 	 adaptor.
 	Make	 sure 	 you 	 tighten 	 the 	 finger 	 screws 	 at 	 each 	 end 	 of 	 the 	 signal 	 cable.
    BEFORE YOU OPERATE THE MONITOR     7 
CONNECTING YOUR MONITOR
[Example of Connection]
NOTE
	Power Cable (Accessory)         

	DVI-D Cable (Accessory for ProLite E2607WS  and ProLite E2607WSD  ) 	
	HDMI  Cable (not Supplied)
	D-Sub Signal Cable (Accessory)   
     Audio Cable (Accessory)Audio Cable (Accessory)
ComputerNOTE
 
						

							
ENGLISH

 Signal Timing
  Change to the desired signal timing listed on page 22: COMPLIANT TIMING.
 Windows 95/98/2000/Me/X P/Vista Plug �� PlayP/Vista Plug ��  Play
 The iiyama LCD monitor complies with DDC1/2B of VESA standard. The Plug  ��  Play function runs 
on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC1/2B compliant computernnecting the monitor to DDC1/2B compliant computer 
with the Signal Cable supplied. 
 For installation on Windows 95/98/2000/Me/XP/Vista: The monitor Information File for iiyama monitors 
may be necessary for your computer and obtained via the Internet, using \
the address: 
                                                    http://www.iiyama.com
	Monitor Drivers are not required in most cases for Windows Vista, Macintosh or Unix  
    operating systems. For further information, please contact your comp\
uter dealer 
				 first 	 for 	 advice.
	For additional information on how to download the driver for your touch \
screen monitor,
 please access the internet site noted above.
NOTE
NOTE
 For optimal viewing it is recommended to look at the full face 
of the monitor.
 Hold the stand so that the monitor does not topple when you 
change the monitor’s angle.
 You  are  able  to  adjust  the  monitor’s  angle  up  to  20  degrees  
backward. (The indication of  20 degrees: tilted LCD panel holds 
for a moment at this point. Tilt the panel gently; using too much 
force can easily cause the tilt angle to exceed 20 degrees.)
 In  order  to  ensure  a  healthy  and  relaxed  body  position 
when  using  the  monitor  at  visual  display  workstations,  it  is 
recommended that the adjusted tilt angle should not exceed 10 
degrees. Adjust the monitor’s angle to your own preference.
  Do  not  touch  the  LCD  screen  when  you  change 
the  angle.  It  may  cause  damage  or  break  the  LCD 
screen.
 	Careful 	 attention 	 is 	 required 	 not 	 to 	 catch 	 your 	 fingers 	
or hands when you change the angle.
  Do  not  tilt  the  post  beyond  20  degrees  except  when 
repacking the monitor in its box.
    To  do  so  may  cause  the  monitor  to  fall  over  and 
break.
COMPUTER SETTING
ADJUSTING THE VIEWING ANGLE
8       BEFORE YOU OPERATE THE MONITOR    
NOTE
NOTE
 
						

							
ENGLISH

     OPERATING THE MONITOR        9
ADJUSTING
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT 
TIMING shown on page 21. You are also able to adjust the picture by following the button operation 
shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS.
 Press the Menu Button to start the On Screen Display feature. There are additional 
Menu items which can be switched by using the / Buttons.  
 Select the Menu item which contains the adjustment icon relating to the adjustment 
you want to make. Press the Select Button. Then, use the / Buttons to highlight 
the desired adjustment icon. 
 Press  the  Select  Button  again.  Use  the /  Buttons  to  make  the  appropriate 
adjustment or setting. 
Adjustments for H. / V. Position, H.Size and Fine Tune are saved for each signal timing. Except for 
these adjustments, all other adjustments have only one setting which app\
lies to all signal timings.
When button operations are aborted during adjustment, On-Screen Display disappears when the 
time set for the OSD Time Out has passed. Also, press the Menu button to quickly turn off the On-
Screen Display. 

NOTE

For example, to correct for vertical position, select Menu item of Image Adjust and then press the 
Select Button. Then, select        (H. / V.Position) by using the  /  Buttons. 
Any  changes  are  automatically  saved  in  the  memory  when  the  On  Screen  Display disappears. 
Turning off the power should be avoided while using the Menu.
An  adjustment  page  appears  after  you  press  the  Select  Button.  Press  the  Select  Button  again. 
Then, use the /  Buttons to change the vertical position settings. The vertical position of the overall display should be changing accordingly while you are doing this.\
Main MenuAuto Image AdjustContrast/BrightnessInput SelectAudio AdjustColor AdjustInformationManual Image AdjustSetup MenuMemory Recall
1 : Exit                                    2 : Select
Main MenuAuto Image AdjustContrast/BrightnessInput SelectAudio AdjustColor AdjustInformationManual Image AdjustSetup MenuMemory Recall
1  : Exit                                       2  : Select
Manual Image Adjust
Horizontal SizeH./V. PositionFine TuneSharpnessVideo Mode Adjustment
1  : Exit                                      2  : Select
OptiColor Mode
 
						

							
10      OPERATING THE MONITOR     

ENGLISH

ADJUSTMENT MENU CONTENTS

Adjustment Item
Problem / Option                       Button to Press

Auto Image  Adjust
Auto Image Adjust *
Only Analog input
A d j u s t  
H .   /   V.   P o s i t i o n ,   H . S i z e   a n d   F i n e   T u n e
 
automatically.

* 
 
For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for 

SCREEN ADJUSTMENTS.

NOTE
The
	
screen
	
becomes
	
dark
	
for
	
approximately
	
five
	
seconds
	
during
	
the
	
adjustment.

Adjustment Item
Problem / Option                       Button to Press

Contrast/Brightness

Too dark 
Too bright
Brightness 
*
1,3

Contrast
*
3
Too dull
Too intense

*1
 
Adjust the Brightness when you are using the monitor in a dark room and \
feel the screen is too 

bright. 
Can not select when ACR is On.
 

You can skip the Menu items and display an adjustment scale directly by using the following button 

operations.
	

Contrast/Brightness/
 
ACR/
 ECO :
Press the 

 Button when the Menu is not displayed.

Contrast, Brightness,ACR and ECO are switched as follows by pressing the  
/

Button 
successively.

 
                          Contrast      Brightness      ACR       ECO      
 

NOTE

ECO 
On        Brightness of back light is reduced.

Off        Normal

*3  Contrast and Brightness adjustment disabled when ECO is active or wh\
en Opticolor Mode is set 

to Text or Cinema or Game or Scenery.

ACR*2
On        Increased contrast ratio 

Off        typical contrast ratio

*2  ACR can not enable the same time when ECO is on.
 
						

							
ENGLISH

     OPERATING THE MONITOR     11     
Adjustment ItemProblem / Option                       Button to Press
Color Adjust
Cool
NormalReddish white (6500K)
Bluish white (9300K)
WarmGreenish white (5400K)
Green
Red
Blue
Too weak
Too strongUser Color
Adjustment ItemProblem / Option                       Button to Press
Audio Adjust
VolumeToo soft
Too loud
Mute
Mute off and on are switched as follows by pressing the Select Button successiv\
ely.
           Mute off      Mute on  NOTE
Return the sound volume to the previous level.
Turn off the sound temporarily.    

Adjustment ItemProblem / Option                       Button to Press
Input Select*
Input Select
Analog,HDMI and DVI are switched as follows by pressing the    Button successively.
Select the Analog input

Input Select
Analog
HDMISelect the HDMI input
DVISelect the DVI input
Analog      HDMI      DVI 
2

*Not a vailable for ProLite E2607WSV .
You can display the Input Select Menu by pressing the     button under no signal input.1
2
See  your  graphic  card  user  guide  for  more  information  about 
changing the resolution and refresh  
NOTE
Information
Displays  information  regarding  the  current  input  signal  coming 
from the graphic card in your computer.
InformationH. Frequency:                               75.0 KHzV. Frequency:                                60.0 HzResolution:                                   1920 x 1200Pixel Clock:                                   154 MHzSerial Number:                              0598781300001Model Number:                             PLE2607WS 
1 : Exit  
 
						

							
ENGLISH

12       OPERATING THE MONITOR      

Adjustment Item
Problem / Option                       Button to Press

Manual Image Adjust

Horizontal Size

Fine Tune

H./V. Position

Too far to the left

Too far to the right

Too low

Too high

H. Position

V. Position

H.  Position  and  V.  Position  are  switched  as  follows  by  pressing  the

/

Button 

successively.

           H. Position      V. Position
 

NOTE

Too narrow

Too wide

To
	correct
	flickering
	text
	or
	lines

Sharpness

Adjust the picture quality at resolutions of 

less 1920 x 1200.

You can change the picture quality (4 steps).  

Video Mode Adjustment

Full Screen

Over Screen

Aspect Ratio 4:3*1
Select full screen 
Select over screen
Select Aspect ratio
*1 It can display in the center of the screen with a 4:3 or 5:4 aspect rati\
o when input video 
resolution is 4:3 or 5:4. 
StandardFor general windows environment 
and monitor default setting
OfficeFor text editing and viewing in a 
word processing environment
MovieFor movie and video environment
GameFor PC game environment
PictureFor displaying outdoor scenery 
images
Standard,	Office,Movie,	Game	and	Picture	are	switched	as	follows	by	pressing	the	/  Button 
successively.      
																													Standard					Office						Movie						Game							Picture
OptiColor Mode
Only Analog Input
Only Analog Input
Only Analog Input
 
						

							
ENGLISH

Adjustment ItemProblem / Option                       Button to Press
Setup Menu
Language Select
OSD Time Out
OSD Position
English
Deutsch
English
German
FrançaisFrench
Spanish
H.PositionOSD is too far to the left
OSD is too far to the right
OSD is too low
OSD is too highV.Position
You can set the OSD display duration time between 5 and 60 seconds.
ItalianoItalian
Espanol
Adjustment ItemProblem / Option                       Button to Press
Memory Recall
Memory RecallFactory-preset data is restored.
FinnishSuomi
Japanese日本語Simplified	 Chinese
Traditional Chinese
    OPERATING THE MONITOR       13     
简体中文
繁体中文
 
						

							
ENGLISH

SCREEN ADJUSTMENTS
 The screen adjustments described in this manual are designed to set image position and minimize 
flicker 	 or 	 blur 	 for 	 the 	 particular 	 computer 	 in 	 use. 	
 The  monitor  is  designed  to  provide  the  best  performance  at  resolution  of  1920  ×  1200,  but  can  not 
provide the best at resolutions of less than 1920 × 1200 because the picture is automatically stretched 
to 	 fit 	 the 	 full 	 screen. It is recommended to operate at resolution of 1920 × 1200 in normal use.
 Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to 
the screen enlargement process.
 It is preferable to adjust the image position and frequency with the monitor controls, rather than the 
computer software or utilities. 
 Perform adjustments after a warm-up period of at least thirty minutes.
 Additional adjustments may be required after the Auto Adjust depending on the resolution or signal 
timing.
 The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment 
pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, H.Size and 
Fine Tune. The other way is performing each adjustment manually.
Perform 	 the 	 Auto 	 Adjust 	 first 	 when 	 the 	 monitor 	 is 	 connected 	 to 	 a 	 new 	 computer, 	 or 	 resolution 	 is 	 changed. 	
If	 the 	 screen 	 has 	 a 	 flicker 	 or 	 blur, 	 or 	 the 	 picture 	 does 	 not 	 fit 	 in 	 the 	 display 	 area 	 after 	 performing 	 the 	
Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen 
adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired pic\
ture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
 Display the picture at the optimum resolution.
 Enter the Test.bmp (screen adjustment pattern) to wallpaper. 
NOTE    Consult the appropriate documentation for doing this.
 	 	 Test.bmp is made at resolution of 1280 × 1024 Set the display position to center in the 
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting 
of 	 “Stretch 	 desktop 	 wallpaper 	 to 	 fit 	 the 	 screen”.
[Adjustment pattern] 

Zebra pattern

Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.      
14        OPERATING THE MONITOR     
 
						

							
ENGLISH

1
 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge 
of the display area.
NOTE  	 When the left side of the picture frame moves apart from the left edge of the display 
area during the H.Size adjustment, adjust steps 1) and 2).
 	 	 Another way to make the H.Size adjustment is to correct the vertical wavy lines in the 
zebra pattern.
 	 		The 	 picture 	 may 	 flicker 	 during 	 the 	 H.Size, 	 H.Position 	 and 	 V.Position 	 adjustment.
 	 	 In case the picture frame is bigger or smaller than the data display area after the H.Size 
adjustment, repeat steps from .
  2) Stretch the right side of the picture frame to the right edge of the display area by adjusting 
the H.Size.
 Press the Auto Button. (Auto Adjust) 
	 Adjust 	 the 	 image 	 manually 	 by 	 following 	 procedure 	 below 	 when 	 the 	 screen 	 has 	 a 	 flicker 	 or 	
blur,	 or 	 the 	 picture 	 does 	 not 	 fit 	 in 	 the 	 display 	 area 	 after 	 performing 	 the 	 Auto 	 Adjust.
	 Adjust	 the 	 V.Position 	 so 	 that 	 the 	 top 	 and 	 bottom 	 of 	 the 	 picture 	 frame 	 will 	 fit 	 to 	 the 	 display 	
area.
NOTE
     OPERATING THE MONITOR       15
 
						

							
ENGLISH

NOTE 		In	 case 	 the 	 strong 	 flicker 	 or 	 blurs 	 remain 	 on 	 a 	 part 	 of 	 the 	 screen, 	 repeat 	 steps 	 and 
		because 	 the 	 H.Size 	 may 	 not 	 be 	 adjusted 	 correctly. 	 If 	 the 	 flicker 	 or 	 blurs 	 still 	 remain, 	
set the refresh rate of computer to low (60Hz) and repeat steps from  again.
 	 	 Adjust the H.Position after the Fine Tune adjustment if the horizontal position moves 
during the adjustment.
  Adjust the Brightness and Color Adjust to get the desired picture after you complete the 
H.Size and Fine Tune adjustments. 
  Put back your favorite wallpaper.
	 Adjust 	 the 	 Fine 	 Tune 	 to 	 correct 	 horizontal 	 wavy 	 noise, 	 flicker 	 or 	 blur 	 in 	 the 	 zebra 	 pattern.
NOTE
16       OPERATING THE MONITOR