Iiyama Prolite E2403ws User Manual

							
ENGLISH
Power Cable(Accessory)
Audio Cable (Accessory)Computer
D-Sub Signal Cable
(Accessory)
DVI-HDMI Cable 
(Accessory)
BEFORE YOU OPERATE THE MONITOR     7
CONNECTING YOUR MONITOR
[Example of Connection]
A Ensure that both the computer and the monitor are switched off.
B Connect the computer to the monitor with the signal cable.(See page 25 \
for CONNECTOR PIN
ASSIGNMENT.)
C Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
D Connect the Power Cable to the monitor first and then to the power suppl\
y.
NOTE„
The signal cables used for connecting the computer and monitor may vary \
with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and\
the computer. The cable supplied with the monitor is for a standard 15 pin  D-Sub connector.
If a special cable is required please contact your local iiyama dealer o\
r regional iiyama office.
„ For connection to Macintosh computers, contact your local iiyama dealer \
or regional
iiyama office for a suitable adaptor.
„ Make sure you tighten the finger screws at each end of the signal cable.\

[ Fitting and Removal of Cable Holder :  PLE2403]
z
 Fitting
A Pull out the hook.
B Hold the both sides of the hook, and remove one
tab at a time.
z
 Removal
A Collect cables at the back of the stand.
B Hold the both sides of the hook, and insert one
tab at a time into the holes.
PLB_E2403WS-e-M021B01.P65 2007/10/05, 9:14
11
 
						

							
ENGLISH
NOTE
„For optimal viewing it is recommended to look at the
full face of the monitor, then adjust the monitors
height and angle to your own preference.
„ Hold the panel so that the monitor does not topple
when you change the monitor’s height or angle.
„ You are able to adjust the monitor’s height up to
130mm. The monitor can also be tilted up to 20°
upward, 5° downward and swiveled 45° to the
right and left.
„ In order to ensure a healthy and relaxed body
position when using the monitor at visual display
workstations, it is recommended that the adjusted
tilt angle should not exceed 10 degrees. Adjust the
monitor’s angle to your own preference.
„ Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD
screen.
„ Careful attention is required not to catch your fingers
or hands when you change the angle.
„ Do not tilt the post beyond 20 degrees except when
repacking the monitor in its box.
To do so may cause the monitor to fall over and
break.
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE :
ProLite B2403WS
8     BEFORE YOU OPERATE THE MONITOR
NOTE
130mm
20˚5˚
45˚ 45˚
„Signal Timing
Change to the desired signal timing listed on page 25: COMPLIANT TIMING.
„ Windows 95/98/2000/Me/XP/Vista Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & \
Play function runs on
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compli\
ant computer with
the Signal Cable supplied.
For installation on Windows 95/98/2000/Me/XP: The monitor Information Fi\
le for iiyama monitors
may be necessary for your computer and obtained via the Internet, using \
the address:
                                                    http://www.iiyama.com
„ Monitor Drivers are not required in most cases for Macintosh or Unix ope\
rating systems.
For further information, please contact your computer dealer first for a\
dvice.
„
For additional information on how to download the driver for your touch \
screen monitor,
please access the internet site noted above.
COMPUTER SETTING
NOTE
PLB_E2403WS-e-M021B01.P65 2007/10/05, 9:14 12
 
						

							
ENGLISH
PANEL ROTATION : ProLite B2403WS
AAdjust the monitor’s height to the maximum.
B Rotate the panel 90 degrees.
Portrait: Turn clockwise.
Landscape: Turn counter clockwise.
C Adjust the monitor’s angle to your preference.
NOTE„
Attempting to rotate without fully extending
upward may cause damage to stand.
„  Screen Rotation should be accessed via the
softOSM software.

The Desktop softOSM software complies with the DDC/CI standard and can b\
e downloaded from the
iiyama website. www.iiyama.com
520
NOTE
NOTE
„ For optimal viewing it is recommended to look at the full face
of the monitor.
„ Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
„ You are able to adjust the monitor’s angle up to 20° upward, 5°
downward.
„ In order to ensure a healthy and relaxed body position when
using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
10 degrees. Adjust the monitor’s angle to your own preference.
„Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD screen.
„ Careful attention is required not to catch your fingers
or hands when you change the angle.
„ Do not tilt the post beyond 20 degrees except when
repacking the monitor in its box.
To do so may cause the monitor to fall over and break.
ADJUSTING THE VIEWING ANGLE : ProLite E2403WS
NOTE
BEFORE YOU OPERATE THE MONITOR     9
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54 13
 
						

							
ENGLISH
10     OPERATING THE MONITOR
ADJUSTING
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at th\
e factory with the COMPLIANT
TIMING shown on page 25. You are also able to adjust the picture by following the button operation\
shown below. For more detailed adjustment s, see page 16 for SCREEN ADJUSTMENTS.
(
( (
(
(Press the ENTER Button to start the On Screen Display feature. There are\
additional Menu items which can be switched by using the     /     Butto\
ns.
B
B B
B
BSelect the Menu item which contains the adjustment icon relating to the
adjustment you want to make. Press the ENTER Button. Then, use the     /\
     Buttons to highlight the desired adjustment icon.
C
C C
C
CPress the ENTER Button again. Use the    /    Buttons to make the approp\
riate
adjustment or setting.
Adjustments for H. / V. Position, Pixel Clock and Phase are saved for each signal timing. Exce\
pt for
these adjustments, all other adjustments have only one setting which app\
lies to all signal timings.
When button operations are aborted during adjustment, On-Screen Display \
disappears when the
time set for the OSD Time has passed. Also, press the EXIT button to quickly turn off the On-
Screen Display.
„
NOTE
„ For example, to correct for vertical position, select Menu item of Geome\
try and then press the
ENTER Button. Then, select          (V.Position) by using the     /     Buttons.
„ Any changes are automatically saved in the memory when the On Screen Dis\
play 
disappears.
Turning off the power should be avoided while using the Menu.
An adjustment page appears after you press the ENTER Button. Then, use t\
he      /      Buttons to
change the vertical position settings. The vertical position of the over\
all display should be
changing accordingly while you are doing this.
Press the EXIT Button lastly, it ends, any changes are saved in the memory.
Main Menu
Luminance
Geometry
ColorOSD Language
Recall
Miscellaneous
Input Select
Audio
Auto Adjust
Main Menu
Luminance
ColorOSD Language
Recall
Miscellaneous
Input Select
Audio
Auto Adjust
Geometry
Geometry
Pixel Clock
Phase
H. Position50
50
5050
V. Position
Geometry
V. Position
50
D
D D
D
D Press the EXIT Button to leave the menu, and the settings you just made \
would
be automatically saved.
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54 14
 
						

							
ENGLISH
ADJUSTMENT MENU CONTENTS
Adjustment Item Problem / Option                       Button to Press
Auto Adjust
Auto Adjust  *
You can skip the Menu items and display an adjustment scale directly by u\
sing the following
button operations.
z Auto Adjust: Press the Auto Button when the Menu is not displayed.Direct
Direct
Adjust H. / V. Position, Pixel Clock and Phase automatically.
* For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 16 for SCREEN ADJUSTMENTS.
Adjustment Item Problem / Option                       Button to Press
Luminance *1
DirectToo dark
Too bright
Brightness 
*2
Contrast Too dull
Too intenseDirect
*1Luminance adjustment disabled when DCR mode is active.
*2Adjust the Brightness when you are using the monitor in a dark room and \
feel the screen is too
bright.
You can skip the Menu items and display an adjustment scale directly by u\
sing the following
button operations.
z Contrast: Press the     Button when the Menu is not displayed.
z Brightness: Press the     Button when the Menu is not displayed.
Direct
Only Analog  Input
OPERATING THE MONITOR     11
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54 15
 
						

							
ENGLISH
12     OPERATING THE MONITOR
Adjustment Item Problem / Option                       Button to Press
Geometry
Phase Pixel Clock
Too left
Too right
Too low
Too highH. Position
V. Position
Too narrow
Too wide
To correct flickering text or lines
Only Analog  Input
Adjustment Item Problem / Option                       Button to Press
Color
9300K
7500K Y ellowish white
Bluish white
Green Red
Blue
Too weak
Too strong
User Preset
6500K Reddish white
OSD Time
H.PositionOSD is too left
OSD is too right
OSD is too low
OSD is too high
You can set the OSD display duration time
between 5 and 30 seconds.
Adjustment Item Problem / Option                       Button to Press
OSD
V.Position
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54 16
 
						

							
ENGLISH
Adjustment Item Problem / Option                       Button to Press
Language
Language
English
Deutsch English
German
Français French
Japanese
Polski
Polish
Dutch
Adjustment Item Problem / Option                       Button to Press
Recall
Recall All Factory-preset data is restored.NoReturn to Menu.
Italiano Italian
Russian
Simplified ChineseEspañol Sp
anishNederlands
OPERATING THE MONITOR     13
Ye s
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54
17
 
						

							
ENGLISH
14     OPERATING THE MONITOR
Adjustment Item Problem / Option                       Button to Press
Miscellaneous
Sharpness1 2 3 4 5
You can change the picture quality from 1 to 5 (sharp to soft).
Press the    Button to change the picture quality in numerical
order. Press the     Button to change the picture quality in reverse
numerical order.
DDC/CI DDC/CI is turned ON.On
Off
DDC/CI is turned OFF.
See your graphic card user guide for more information
about changing the resolution and refresh.NOTE
Displays information regarding the current input signal coming
from the graphic card in your computer.
Display Information
DDC/CI On and Off are switched as follows by pressing the    Button successively. On     OffNOTE
Miscellaneous
Display Information
1920x1200  @ 60 Hz
DCR Increased Contrast RatioOn
Off
Typical Contrast Ratio
OD *1You can set the OverDrive level between 0 and 5. It will improve
the gray level response time of the LCD panel. A higher level
results in a faster response time.
Display Mode *2
Expansion display
Full
1 : 1
Displayed at the same magnification
AspectExpansion display of Aspect
*
1OD cannot enable at the same time when Display Mode is set to 1 : 1 or Aspect, and Vertical
Frequency is more than 60Hz. When OD is activated, some level of image r\
etention will be caused.
For optimal viewing, the recommended level is 3 or lower.
*
2Display Mode is locked to Full and you cannot select 1 : 1 or Aspect when receiving 1920 x 1080
signal.
0 1 2 3 4 5
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:54 18
 
						

							ENGLISH
Adjustment Item Problem / Option                       Button to Press
Audio
VolumeToo soft
Too loud
Mute
Return the sound volume to the previous level. Turn off the sound temporarily.Off On
Mute On and Off are switched as follows by pressing the    Button successively.
On      OffNOTE„
„       is displayed of AUDIO in the Main Menu while
 Mute is active.
„       is displayed of AUDIO in the Main Menu while
 Mute is not active.
You can skip the Menu items and display an adjustment scale directly by using the following
button operations.
zInput Select: Press the Exit Button when the Menu is not displayed.
Direct
Direct
Audio Input SelectAutomatically detects audio input.Auto Detect
Allows manual selection of audio input. Line-in
Input Select
When only one of the two signal inputs is connected to the signal source, the one
connected is automatically selected. Input Select function is not available if there is no
signal input from the selected connector or during the power management mode.NOTE
Select the Analog input.
Select the Digital input.D-sub
HDMI
Adjustment Item Problem / Option                       Button to Press
Input Select
OPERATING THE MONITOR     15
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5419
 
						

							ENGLISH
16     OPERATING THE MONITOR
SCREEN ADJUSTMENTS
„The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„The monitor is designed to provide the best performance at resolution of 1920 × 1200, but can not
provide the best at resolutions of less than 1920 × 1200 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1920 × 1200 in normal use.
„Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
„It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
„Perform adjustments after a warm-up period of at least thirty minutes.
„Additional adjustments may be required after the Auto Adjust depending on the resolution or signal
timing.
„The Auto Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Pixel Clock
and Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://
www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
A AA A
ADisplay the picture at the optimum resolution.
B BB B
BEnter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE„Consult the appropriate documentation for doing this.
„Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft
® PLUS! 95/98 cancel the setting
of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5420