Iiyama Prolite E2207ws 2 User Manual

							ENGLISH
 Ensure that both the computer and the monitor are switched off.
  Connect the computer to the monitor with the signal cable.
  Connect  the  monitor  to  the  audio  equipment  with  the Audio  Cable  for  computer  when  using  the 
audio features.
  Connect the Power Cable to the 	monitor	first	and	then	to	the	power	supply.
NOTE   The  signal  cables  used  for  connecting  the  computer  and  monitor  may  vary  with  the  type  of 
computer used. An incorrect connection may cause serious damage to both the monitor and 
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. 
If  a  special  cable  is  required  please  contact  your  local  iiyama  dealer  or  regional  iiyama 
office.
   For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama 
office	for	a	suitable	adaptor.
  	Make	sure	you	tighten	the	finger	screws	at	each	end	of	the	signal	cable.
BEFORE YOU OPERATE THE MONITOR       7     
CONNECTING YOUR MONITOR
[Example of Connection]
NOTE
Power Cable 
(Accessory) D-Sub Cable 
(Accessory)
DVI-D Cable
(Accessory) Audio Cable
(Accessory)
 
						

							ENGLISH
 Signal Timing
  Change to the desired signal timing listed on page 21: COMPLIANT TIMING.
  Windows 95/98/2000/Me/XP/Vista Plug & Play
  The iiyama LCD monitor complies with DDC1/2B
TM of VESA standard. The Plug & Play function runs 
on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC1/2BTM compliant computer 
with the Signal Cable supplied. 
  For installation on Windows 95/98/2000/Me/XP/Vista: The monitor Information File for iiyama monitors 
may be necessary for your computer and obtained via the Internet, using \
the address: 
                                                     http://www.iiyama.com
	 Monitor  Drivers  are  not  required  in  most  cases  for  Windows  Vista,Macintosh  or  Unix 
operating	systems.		 For	 further	information,	 please	contact	 your	computer	 dealer	first	for	
advice. 	 For additional information on how to download the driver for your touch \
screen monitor,
  please access the internet site noted above.
NOTE NOTE
 
For optimal viewing it is recommended to look at the full face 
of the monitor.
  Hold the stand so that the monitor does not topple when you 
change the monitor’s angle.
  You  are  able  to  adjust  the  monitor’s  angle  up  to  20  degrees  
backward. (The indication of  20 degrees: tilted LCD panel holds 
for a moment at this point. Tilt the panel gently; using too much 
force can easily cause the tilt angle to exceed 20 degrees.)
  In  order  to  ensure  a  healthy  and  relaxed  body  position 
when  using  the  monitor  at  visual  display  workstations,  it  is 
recommended that the adjusted tilt angle should not exceed 10 
degrees. Adjust the monitor’s angle to your own preference.
   Do  not  touch  the  LCD  screen  when  you  change 
the  angle.  It  may  cause  damage  or  break  the  LCD 
screen.
  	Careful	 attention	is	required	 not	to	catch	 your	fingers	
or hands when you change the angle.
   Do  not  tilt  the  post  beyond  20  degrees  except  when 
repacking the monitor in its box.
    To  do  so  may  cause  the  monitor  to  fall  over  and 
break.
COMPUTER SETTING
ADJUSTING THE VIEWING ANGLE
8         BEFORE YOU OPERATE THE MONITOR    
NOTE
NOTE
 
						

							ENGLISH
   OPERATING THE MONITOR         9       
ADJUSTING
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT 
TIMING shown on page 21. You are also able to adjust the picture by following the button operation 
shown below. For more detailed adjustments, see page
 14 for SCREEN ADJUSTMENTS.
  Press the Menu Button to start the On Screen Display feature. There are additional 
Menu items which can be switched by using the      /     Buttons.  
 Select the Menu item which contains the adjustment icon relating to the adjustment 
you want to make. Press the Select Button. Then, use the   /    Buttons to highlight 
the desired adjustment icon. 
  Press  the  Select  Button  again.  Use  the    /   Buttons  to  make  the  appropriate 
adjustment or setting. 
Adjustments for H. / V. Position, H.Size and Fine Tune are saved for each signal timing. Except for 
these adjustments, all other adjustments have only one setting which app\
lies to all signal timings.
When button operations are aborted during adjustment, On-Screen Display disappears when the 
time set for the OSD Time Out has passed. Also, press the Menu button to quickly turn off the On-
Screen Display. 

NOTE
 For example, to correct for vertical position, select Menu item of Image Adjust and then press the 
Select Button. Then, select        (H. / V.Position) by using the 
 /   Buttons. 
 Any  changes  are  automatically  saved  in  the  memory  when  the  On  Screen  Display 
disappears. 
Turning off the power should be avoided while using the Menu.
An  adjustment  page  appears  after  you  press  the  Select  Button.  Press  the  Select  Button  again. 
Then, use the
   /    Buttons to change the vertical position settings. The vertical position of the 
overall display should be changing accordingly while you are doing this.\
Main Menu                                        VGAAuto Image Adjust
Contrast/Brightness
Input Select
Audio Adjust
Color Adjust
Information
Manual Image Adjust
Setup Menu
Memory Recall
1 : Exit                                    2 : Select
Main Menu                                         VGA     
Auto Image Adjust
Contrast/Brightness
Input Select
Audio Adjust
Color Adjust
Information
Manual Image Adjust
Setup Menu
Memory Recall
1  : Exit                                       2  : SelectManual Image Adjust
Horizontal Size H./V. Position
Fine Tune
Sharpness
Video Mode adjust
1  : Exit                                      2  : Select Opticolor Mode
 
						

							ENGLISH
10       OPERATING THE MONITOR     
ADJUSTMENT MENU CONTENTS
Adjustment ItemProblem / Option                       Button to Press
Adjust H.  /  V.  Position,  H.Size  and  Fine  Tune  
automatically.
*   For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for 
SCREEN ADJUSTMENTS.
NOTE The	screen	becomes	dark	for	approximately	five	seconds	during	the	adjustment.
Adjustment Item
Problem / Option                       Button to Press
Contrast/Brightness
Too dark 
Too bright Too dull
Too intense
You can skip the Menu items and display an adjustment scale directly by using the following button 
operations.
	 Contrast/Brightness/  ACR/ ECO Mode :Press the 
 Button when the Menu is not displayed.
Contrast,  Brightness,ACR  and  ECO  Mode  are  switched  as  follows  by  pressing  the 

/Button 
successively.
                             Contrast      Brightness      ACR       ECO Mode       
NOTE
ECO ModeOn        Brightness of back light is reduced.
Off        Normal
Auto Image  Adjust
Brightness
 *1,2,3
Contrast*2
Off        Normal 
On        Brightness of back-light is reduced.
ACR
*1  Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too 
bright.
*2  Contrast and Brightness adjustment disabled when ECO Mode is active \
or when Opticolor Mode 
is set to Text or Cinema or Game or Scenery.
*3  Brightness adjustment disabled when ACR  is active.ACR and ECO Mode can not enable at the  same time.
Auto Image Adjust *
Only Analog input
 
						

							ENGLISH
     OPERATING THE MONITOR        11     
Adjustment ItemProblem / Option                       Button to Press
Audio Adjust
Volume Too soft
Too loud
Mute
Mute off and on are switched as follows by pressing the Select Button successiv\
ely.
            Mute off      Mute on NOTE
Return the sound volume to the previous level.
Turn off the sound temporarily.    

Adjustment Item Problem / Option                       Button to Press
Input Select
Input Select
VGA and DVI are switched as follows by pressing  the / Button successively.
Select the Analog input
Input Select
VGA
DVI
Select the Digital
 input
 VGA           DVI
When only one of the two signal inputs is connected to the signal source\
, the one 
connectedis automatically selected. Input Select function is not available if there is no 
signal input from theselected connector or during the power management m\
ode.

See  your  graphic  card  user  guide  for  more  information  about 
changing the resolution and refresh   NOTE
Information
Displays  information  regarding  the  current  input  signal  coming 
from the graphic card in your computer.Information                                       VGA                                    
1 : Exit  
H. Frequency:                               80.0 KHz
V. Frequency:                                75.0 Hz
Resolution:                                   1680 x 1050
Pixel Clock:                                   146 MHz
Serial Number:                              0598381300001
Model Number:                             PLE2207WS 
Adjustment Item
Problem / Option                       Button to Press
Color Adjust
9300K
6500K
Reddish white Bluish white
5400KGreenish white
Green Red
BlueToo weak
Too strong
User Color2
 
						

							ENGLISH
12        OPERATING THE MONITOR       
Adjustment ItemProblem / Option                       Button to Press
Manual Image Adjust
Horizontal Size*1
Fine Tune*1
H./V. Position*1
Too far to the left
Too far to the right
Too low
Too high
H. Position
V. Position
H.  Position  and  V.  Position  are  switched  as  follows  by  pressing  the
/Button 
successively.
            H. Position      V. Position NOTE
Too narrow
Too wide
To	correct	flickering	text	or	lines
Sharpness Adjust the picture quality at resolutions of 
less 1680 x 1050.
You can change the picture quality (3 steps).  
Video Mode AdjustFull Screen
Over Screen
Aspect Ratio*2
Select full screen 
Select over screen
Select Aspect ratio
*1 Only Analog input.
*2 It can display in the center of the screen with a 4:3, 5:4 aspect ratio when input video resolution  is 4:3, 5:4.
You can skip the Menu items and display an adjustment scale directly by u\
sing the following 
button operations.
OptiColor Mode:Press the 
 Button when the Menu is not displayed. Standard
For general windows environment 
and monitor default setting
Game For PC game environment
Cinema For movie and video environment
Scenery For displaying outdoor scenery 
images
Text For text editing and viewing in a 
word processing environment
Standard, Game,Cinema, Scenery and Text are switched as follows by pressing the 
/  
Button successively.      
                             Standard       Game      Cinema      Scenery      Text
OptiColor Mode
 
						

							ENGLISH
Adjustment ItemProblem / Option                       Button to Press
Setup Menu
Language Select
OSD Time Out
OSD Position
English
Deutsch English
German
Français
French
Spanish
H.Position OSD is too far to the left
OSD is too far to the right
OSD is too low
OSD is too high
V.Position
OSD Background Return the background of OSD
On Italiano
Italian
Espanol
Adjustment Item
Problem / Option                       Button to Press
Memory Recall
Memory Recall
Factory-preset data is restored.Finnish
Suomi
Japanese
日本語
Simplified	Chinese
Traditional Chinese
     OPERATING THE MONITOR        13    
简体中文
繁体中文
The background of OSD is made transparent
Off
You can set the OSD display duration time between 5 
and 60 seconds.
 
						

							ENGLISH
SCREEN ADJUSTMENTS
 The screen adjustments described in this manual are designed to set image position and minimize 
flicker	or	blur	for	the	particular	computer	in	use.	
  The  monitor  is  designed  to  provide  the  best  performance  at  resolution  of  1680  ×  1050,  but  can  not 
provide the best at resolutions of less than 1680 × 1050  because the picture is automatically stretched 
to	fit	the	full	screen. It is recommended to operate at resolution of 1680 × 1050 in normal use.
  Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to 
the screen enlargement process.
  It is preferable to adjust the image position and frequency with the monitor controls, rather than the 
computer software or utilities. 
  Perform adjustments after a warm-up period of at least thirty minutes.
  Additional adjustments may be required after the Auto Adjust depending on the resolution or signal 
timing.
  The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment 
pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, H.Size and 
Fine Tune. The other way is performing each adjustment manually.
Perform 	the 	Auto 	Adjust 	first 	when 	the 	monitor 	is 	connected 	to 	a 	new 	computer, 	or 	resolution 	is 	changed.	
If	 the	 screen	 has	a	flicker	 or	blur,	 or	the	 picture	 does	not	fit	in	the	 display	 area	after	performing	 the	
Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen 
adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired pic\
ture.
This manual explains adjustment under Windows 95/98/2000/Me/X P/Vista.
  Display the picture at the optimum resolution.
  Enter the Test.bmp (screen adjustment pattern) to wallpaper. 
NOTE    Consult the appropriate documentation for doing this.
  	 	  Test.bmp is made at resolutio n of 1280 × 1024. Set the display position to center in the 
wallpaper setting dialogue box. If you use Microsoft
® PLUS! 95/98 cancel the setting 
of	“Stretch	desktop	wallpaper	to	fit	the	screen”.
[Adjustment pattern] 
Zebra pattern
Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.      
14       OPERATING THE MONITOR     
 
						

							ENGLISH
1
 1) Adjust the H.Position so that the left side of the picture frame will move to the left edge 
of the display area.
NOTE  	 When the left side of the picture frame moves apart from the left edge of the display 
area during the H.Size adjustment, adjust steps 1) and 2).
  	 	  Another way to make the H.Size adjustment is to correct the vertical wavy lines in the 
zebra pattern.
  	 	 	The	picture	may	flicker	during	the	H.Size,	H.Position	and	V.Position	adjustment.
  	 	  In case the picture frame is bigger or smaller than the data display area after the H.Size 
adjustment, repeat steps from .
 
2) Stretch the right side of the picture frame to the right edge of the display area by adjusting 
the H.Size.
 
Press the Auto Button. (Auto Image Adjust) 
	 Adjust	 the	image	 manually	 by	following	procedure	 below	when	the	screen	 has	a	flicker	 or	
blur,	or	the	picture	does	not	fit	in	the	display	area	after	performing	the	 Auto	Adjust.
	 Adjust	 the	V.Position	 so	that	 the	top	 and	 bottom	 of	the	 picture	 frame	will	fit	to	the	 display	
area.
NOTE
     OPERATING THE MONITOR         15
 
						

							ENGLISH
NOTE 		In	case	 the	strong	 flicker	or	blurs	 remain	 on	a	part	 of	the	 screen,	 repeat	steps	 and 
		 because	 the	H.Size	 may	not	be	adjusted	 correctly.	 If	the	 flicker	 or	blurs	 still	remain,	
set the refresh rate of computer to low (60Hz) and repeat steps from   again.
  	 	  Adjust the H.Position after the Fine Tune adjustment if the horizontal position moves 
during the adjustment.
  Adjust the Brightness and Color Adjust to get the desired picture after you complete the 
H.Size and Fine Tune adjustments. 
  Put back your favorite wallpaper.
	 Adjust	the	Fine	Tune	to	correct	horizontal	wavy	noise,	flicker	or	blur	in	the	zebra	pattern.NOTE
     16       OPERATING THE MONITOR