Iiyama Prolite E2202wsv User Manual

							ENGLISH
Menu : 3
(Analog)
Japanese
Adjustment Item
Menu:3
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
Problem / Option                                             Button to Press
OSD Position1 2 3 4 5
You can move the OSD display area
to any one of the following 5 positions
within the overall display:
Italiano LanguageEnglish
DeutschEnglish
FrançaisEspañol
FrenchSpanish
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
Too soft
Too loud
Volume *1Direct
Return to Menu
Highlight “Menu : 3” again.
ResetNO
YESReturn to Menu.
Factory-preset data is restored.
NOTE„       is displayed while Mute is active.
Auto
AnalogSelect the signal input automatically.
Select the Analog input (D-SUB). Signal Select *2Direct
When both Analogue and Digital cables are connected, you can switch between them
using the direct access facility described earlier.  If only one input is present, this will
automatically be selected.  In Power Management Mode input switching is disabled.NOTE
See page 13 for Direct adjustment.Direct
OSD Off TimerSet the OSD Off Timer for 3-60 seconds.
DigitalSelect the Digital input (DVI-D).Italian
OPERATING THE MONITOR     17
*1Available for ProLite E2202WS / E2202WSV only.
*
2Available for ProLite E2201W / E2202WS only.German
 
						

							ENGLISH
18     OPERATING THE MONITOR
User
Menu:1
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
GR
B
Adjustment Item Problem / Option                               Button to Press
Too dark
Too brightBrightness *1
ContrastToo dull
Too intense
*1Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
Direct
Direct
Sharpness
Normal
Mode1High contrast
Mode2DarkGamma
Color Temp.Color 1: 9300K
1
NOTE„sRGB is an international standard which defines and unifies the difference of color
appearance between equipment.
„You can not adjust the Brightness, Contrast, Gamma and Economy Mode during sRGB
mode because those settings are locked.
„        is displayed while sRGB is active.3
Color 3: 6500K Color 2: 7500K
sRGB
Too weak
Too strong s
1 2 3 4 5
Adjust the picture quality at resolutions of less than 1680
× 1050.
You can change the picture quality from 1 to 5 (sharp to soft).
Press the + Button to change the picture quality in
numerical order. Press the – Button to change the picture
quality in reverse numerical order.
Digital Input : Available for ProLite E2201W / ProLite E2202WS only.
See page 13 for Direct adjustment.Direct
2
Off
 
						

							ENGLISH
Menu : 1
(Digital)
Return to MenuHighlight “Menu : 1” again.
Mode1Brightness of back-light is reduced.
Mode2Brightness of back-light is reduced more than Mode1.
Economy ModeOffNormal
Problem / Option Adjustment Item
NOTE„       is displayed while Economy Mode is active.
OPERATING THE MONITOR     19
 
						

							ENGLISH
20     OPERATING THE MONITOR
Menu : 2
(Digital)
Japanese
Adjustment Item
Menu:2
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
Problem / Option                                             Button to Press
OSD Position1 2 3 4 5
You can move the OSD display area
to any one of the following 5 positions
within the overall display:
Italiano LanguageEnglish
DeutschEnglish
German
FrançaisEspañol
French
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
Too soft
Too loud
Volume *1Direct
Return to Menu
Highlight “Menu : 2” again.
ResetNO
YESReturn to Menu.
Factory-preset data is restored.
NOTE„       is displayed while Mute is active.
Auto
AnalogSelect the signal input automatically.
Select the Analog input (D-SUB). Signal SelectDirect
When both Analogue and Digital cables are connected, you can switch between them
using the direct access facility described earlier.  If only one input is present, this will
automatically be selected.  In Power Management Mode input switching is disabled.NOTE
See page 13 for Direct adjustment.Direct
OSD Off TimerSet the OSD Off Timer for 3-60 seconds.
DigitalSelect the Digital input (DVI-D).Italian
*
1Available for ProLite E2202WS only.
 
						

							ENGLISH
SCREEN ADJUSTMENTS
„The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„The monitor is designed to provide the best performance at resolution of 1680 × 1050, but can not
provide the best at resolutions of less than 1680 × 1050 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1680 × 1050 in normal use.
„Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
„It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
„Perform adjustments after a warm-up period of at least thirty minutes.
„Additional adjustments may be required after the Auto Set-up depending on the resolution or signal
timing.
„The Auto Set-up may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Clock, Phase and
Position. The other way is performing each adjustment manually.
Perform the Auto Set-up first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Set-up, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://
www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
A AA A
ADisplay the picture at the optimum resolution.
B BB B
BEnter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE„Consult the appropriate documentation for doing this.
„Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft
® PLUS! 95/98 cancel the setting
of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Zebra pattern
This is the image
displayed at 1280 × 1024.Color bar
Picture frame
NOTE
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
OPERATING THE MONITOR     21
 
						

							ENGLISH
22     OPERATING THE MONITOR
+
–
F FF F
F1) Adjust the H-Position so that the left side of the picture frame will move to the left
edge of the display area.
NOTE„When the left side of the picture frame moves apart from the left edge of the display
area during the Clock adjustment, adjust steps 1) and 2).
„Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
„The picture may flicker during the Clock, H-Position and V-Position adjustment.
„In case the picture frame is bigger or smaller than the data display area after the Clock
adjustment, repeat steps from 
C.
+
–
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
+
–
C CC C
CPress the Auto Button. (Auto Set-up)
D DD D
DAdjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Set-up.
E EE E
EAdjust the V-Position so that the top and bottom of the picture frame will fit to the
display area.
NOTE
 
						

							ENGLISH
NOTE„In case the strong flicker or blurs remain on a part of the screen, repeat steps 
F and
G  because the Clock may not be adjusted correctly. If the flicker or blurs still remain,
set the refresh rate of computer to low (60Hz) and repeat steps from 
C again.
„Adjust the H-Position after the Phase adjustment if the horizontal position moves
during the adjustment.
H HH H
HAdjust the Brightness and Color Temp. to get the desired picture after you complete
the Clock and Phase adjustments.
Put back your favorite wallpaper. G GG G
GAdjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
+
–
NOTE
OPERATING THE MONITOR     23
 
						

							ENGLISH
0  2W 100% POWER
CONSUMPTION
Blue
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.NOTE
„
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly. „
POWER MANAGEMENT FEATURE
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again. The power management feature of this product complies with power saving requirement of E
NERGY
STA R® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
„
24     OPERATING THE MONITOR
 
						

							ENGLISH
TROUBLE SHOOTING
Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance. 3.
Problem Check
The picture does
not appear.
(Power indicator
does not light up.)The Power Cable is firmly seated in the socket. †
†
†The AC socket is live. Please check with another piece of equipment.
†If the blank screen saver is in active mode, touch the keyboard or the
mouse.
†
Increase the Contrast and/or Brightness.
The computer is ON.
†
The Signal Cable is properly connected. †The Power Switch is turned ON. A
†The signal timing of the computer is within the specification of the monitor.
(Power indicator
is orange.)†
If the monitor is in power management mode, touch the keyboard or the
mouse.
The screen is not
synchronized.†The Signal Cable is properly connected.
†The signal timing of the computer is within the specification of the monitor. B†
The signal timing of the computer is within the specification of the monitor.
†The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.†The signal timing of the computer is within the specification of the monitor.
The screen is
too bright or too
dark.
The screen is
shaking. C
D
EThe video output level of the computer is within the specification of the
monitor. †
†The power voltage is within the specification of the monitor.
†
The signal timing of the computer is within the specification of the monitor. The computer is ON.
The Signal Cable is properly connected. †
† 1. If the monitor fails to operate correctly, please follow the steps below for a possible solution.
(Power indicator
is blue.)
TROUBLE SHOOTING     25
 
						

							ENGLISH
Problem Check
No sound.*
†The Audio Cable is properly connected.
†The audio output level of the audio equipment is within the specification of
the monitor. F†The audio equipment (computer etc.) is ON.
†The Volume is turned up.
†The Mute is OFF.
The sound is too*
loud or too quiet. G†The audio output level of the audio equipment is within the specification of
the monitor.
A strange noise is*
heard. H†The Audio Cable is properly connected.
* Available for ProLite E2202WS / E2202WSV only.
26     TROUBLE SHOOTING