Iiyama Prolite E1902s User Manual

							ENGLISH
FITTING AND REMOVAL OF BASE :
ProLite E1902S / E1902WS / E1902WSV
Install the stand on a stable surface. The monitor may cause injury or damage if it
falls or is dropped. 
						

							ENGLISH
CONTROLS AND CONNECTORS :
ProLite E1902S / E1902WS / E1902WSV
AMenu Button (MENU)
B+ Button (               )
CPower Switch (     )
D– Button (               )
EAuto Button (AUTO)
FPower Indicator
Blue:Normal operation
Orange:Power Management

						

							ENGLISH
BEFORE YOU OPERATE THE MONITOR     8
CONTROLS AND CONNECTORS : ProLite B1902S
AMenu Button (MENU)
B+ Button (               )
CPower Switch (     )
D– Button (               )
EAuto Button (AUTO)
FPower Indicator
Blue:Normal operation
Orange:Power Management

						

							ENGLISH
Audio Cable (Accessory)
Computer D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable* Power Cable
(Accessory)
CONNECTING YOUR MONITOR :
ProLite E1902S / E1902WS / E1902WSV
[Example of Connection] AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the signal cable. (See page 34 for CONNECTOR PIN
ASSIGNMENT.)
CConnect the monitor to the audio equipment with the Audio Cable when using the audio features.
DConnect the Power Cable to the monitor first and then to the power supply.
NOTE
						

							ENGLISH
BEFORE YOU OPERATE THE MONITOR     10
CONNECTING YOUR MONITOR : ProLite B1902S
[Example of Connection] AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the signal cable. (See page 34 for CONNECTOR PIN
ASSIGNMENT.)
CConnect the monitor to the audio equipment with the Audio Cable when using the audio features.
DConnect the Power Cable to the monitor first and then to the power supply.
NOTE
						

							ENGLISH
ADJUSTING THE VIEWING ANGLE :
ProLite E1902S / E1902WS / E1902WSV

						

							ENGLISH
BEFORE YOU OPERATE THE MONITOR     12
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B1902S

						

							ENGLISH
13     OPERATING THE MONITOR
The bar shows 
the progress of the 
adjustment being made.+
–50
V-Position
Menu:1
1280 × 1024
H:80.0KHz  V:75.0Hz
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 33. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 22 for SCREEN ADJUSTMENTS.
( (( (
(Press the Menu Button to start the On Screen Display feature. There are
additional Menu pages which can be switched by using the +/– Buttons.
B BB B
BSelect the Menu page which contains the adjustment icon relating to the
adjustment you want to make. Press the Menu Button again. Then, use the
+/– Buttons to highlight the desired adjustment icon. Press the Menu Button
again.
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Off Timer has passed. The Auto Button can be used to exit OSD window
immediately. 
						

							ENGLISH
ADJUSTMENT MENU CONTENTS
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
zBrightness / Contrast / Volume: To display direct menu press either of the +/- Buttons.  Continue
to use the +/- Buttons to select the adjustments required.
z  Auto Set-up: Press the Auto Button when the Menu is not displayed.
z  Volume (Mute): With the OSD menu off, the pressing and holding of the Menu Button for 1-2
seconds will enable/disable the Audio Mute facility.
z  Signal Select *: With the OSD menu off, pressing and holding the Auto Button for 1-2 seconds will
switch the input signal from Analogue to Digital.
z  Lock Out:With the OSD menu off, pressing and holding the Menu and ‘-‘ Buttons
simultaneously for a period of at least 7 seconds will enable and disable the OSD
Lock Out mode.
       is displayed while Lock Out is active.
Direct
OPERATING THE MONITOR     14
*Available for ProLite E1902S / E1902WS / B1902S only.
 
						

							ENGLISH
15     OPERATING THE MONITOR
Menu:1
1280 × 1024
H:80.0KHz  V:75.0Hz
Adjustment Item Problem / Option                       Button to Press
Too dark
Too brightBrightness *1
ContrastToo dull
Too intense
To correct flickering text or linesClock *2
Phase *2
H-PositionToo far to the left
Too far to the right
V-PositionToo low
Too high
Return to MenuHighlight “Menu : 1” again.
To correct flickering text or lines
Direct
Direct
*1Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
*
2See page 22 for SCREEN ADJUSTMENTS.
Menu : 1
(Analog) Analog Input
See page 14 for Direct adjustment.Direct