Iiyama Prolite B2403ws User Manual

							ENGLISH
1
F FF F
F1) Adjust the H.Position so that the left side of the picture frame will move to the left
edge of the display area.
NOTE„When the left side of the picture frame moves apart from the left edge of the display
area during the Pixel Clock adjustment, adjust steps 1) and 2).
„Another way to make the Pixel Clock adjustment is to correct the vertical wavy lines
in the zebra pattern.
„The picture may flicker during the Pixel Clock, H.Position and V.Position adjustment.
„In case the picture frame is bigger or smaller than the data display area after the Pixel
Clock adjustment, repeat steps from 
C. 2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Pixel Clock.
C CC C
CPress the Auto Button. (Auto Adjust)
D DD D
DAdjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Adjust.
E EE E
EAdjust the V.Position so that the top and bottom of the picture frame will fit to the
display area.
NOTE
OPERATING THE MONITOR     17
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5421
 
						

							ENGLISH
18     OPERATING THE MONITOR
NOTE„In case the strong flicker or blurs remain on a part of the screen, repeat steps 
F and
G  because the Pixel Clock may not be adjusted correctly. If the flicker or blurs still
remain, set the refresh rate of computer to low (60Hz) and repeat steps from 
C
again.
„Adjust the H.Position after the Phase adjustment if the horizontal position moves
during the adjustment.
H HH H
HAdjust the Brightness and Color to get the desired picture after you complete the
Pixel Clock and Phase adjustments.
Put back your favorite wallpaper. G GG G
GAdjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.NOTE
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5422
 
						

							ENGLISH
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.NOTE„
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly. „
POWER MANAGEMENT FEATURE
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again. The power management feature of this product complies with power saving requirement of E
NERGY
STA R® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
„
0  2 W 100% POWER
CONSUMPTION
Green
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
OPERATING THE MONITOR     19
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5423
 
						

							ENGLISH
20     TROUBLE SHOOTING
TROUBLE SHOOTING
Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance. 3.
Problem Check
†
†
†The AC socket is live. Please check with another piece of equipment.
†If the blank screen saver is in active mode, touch the keyboard or the
mouse.
†
Increase the Contrast and/or Brightness.
The computer is ON.
†
The Signal Cable is properly connected. †The Power Switch is turned ON.
A
†The signal timing of the computer is within the specification of the monitor.
(Power indicator
is orange.)†
If the monitor is in power management mode, touch the keyboard or the
mouse.
The screen is not
synchronized.†The Signal Cable is properly connected.
†The signal timing of the computer is within the specification of the monitor.B
†
The signal timing of the computer is within the specification of the monitor.
†The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.†The signal timing of the computer is within the specification of the monitor.
The screen is
too bright or too
dark.
The screen is
shaking. C
D
EThe video output level of the computer is within the specification of the
monitor. †
†The power voltage is within the specification of the monitor.
†
The signal timing of the computer is within the specification of the monitor. The computer is ON.
The Signal Cable is properly connected. †
† 1. If the monitor fails to operate correctly, please follow the steps below for a possible solution.
(Power indicator
is green.)The picture does
not appear.
(Power indicator
does not light up.)
The Power Cable is firmly seated in the socket.
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5424
 
						

							ENGLISH
Problem Check
No sound.
†The Audio Cable is properly connected.
†F†The audio equipment (computer etc.) is ON.
†The Volume is turned up.
†The Mute is OFF.
The sound is too
loud or too quiet. G†The audio output level of the audio equipment is within the specification of
the monitor.
A strange noise is
heard. H†The Audio Cable is properly connected.
For better environment protection please dont dispose your monitor.
Please visit our web site: www.iiyama.com/recycle for monitor recycling.
RECYCLING INFORMATION
The audio output level of the audio equipment is within the specification of
the monitor.
TROUBLESHOOTING     21
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5425
 
						

							ENGLISH
22     APPENDIX
SPECIFICATIONS : ProLite B2403WS
APPENDIX
LCD Panel
Size Driving system
a-Si TFT Active Matrix
Diagonal: 61.2cm  / 24.0
0.270mm H × 0.270mm V
Response time Pixel pitch
2ms (Gray to Gray)
Display Colors Approx.16.7M (6bit+2bit dithering)
Sync FrequencyHorizontal: 31.0-83.0kHz, Vertical: 56-75Hz
Dot Clock162MHz maximum
Maximum Resolution1920 × 1200, 2.3 MegaPixels
Input Connector
D-Sub mini 15 pin, HDMI
Input Sync Signal
Separate sync: TTL, Positive or Negative Plug & PlayVESA DDC2B
TM
65W maximum, Power management mode: 2W maximum* Power Consumption
Dimensions / Net Weight 566.0×  445.0-575.0  ×  220.0mm  /  22.3  ×  17.5-22.  6×  8.7 (W×H×D),
8.7kg / 19.2lbs
Upward: 20 degrees  Downward: 5 degrees
Right / Left : 45 degrees each Viewable angle
Right / Left : 85 degrees each, Up:85 degrees, Down: 75 degrees (Typical)
Maximum Screen Size 518.4mm W × 324.0mm H / 20.4 W × 12.8 H
Power Source100-240VAC, 50/60Hz, 1.5A
Environmental
Considerations
Approvals
TCO ’03, CE, TÜV-GS / MPR3(prEN50279) / ISO 13406-2,
FCC-B, UL / C-UL, VCCI-B, GOST-R Tilt Angle
* Condition: Audio equipment is not connected.
NOTE
Brightness
Contrast ratio300cd/m2 (Maximum)
1000 : 1 (Typical), 2000 : 1 (DCR)
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital: HDMI (1.1) Input Video Signal
Input Audio  Signal 0.5Vrms maximum
Speakers 2W × 2 (Stereo speakers)
Input Audio  Connector ø 3.5mm mini jack (Stereo)
Operating: Temperature
Humidity
Storage:
-20 to 60°C / -4 to 140°F
Humidity5 to 35°C / 41 to 95°F
10 to 70% (No condensation)10 to 80% (No condensation)
Temperature
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5426
 
						

							ENGLISH
APPENDIX     23
SPECIFICATIONS : ProLite E2403WS
LCD Panel
Size Driving system
a-Si TFT Active Matrix
Diagonal: 61.2cm  / 24.0
0.270mm H × 0.270mm V
Response time Pixel pitch
2ms (Gray to Gray)
Display Colors Approx.16.7M (6bit+2bit dithering)
Sync FrequencyHorizontal: 31.0-83.0kHz, Vertical: 56-75Hz
Dot Clock162MHz maximum
Maximum Resolution1920 × 1200, 2.3 MegaPixels
Input Connector
D-Sub mini 15 pin, HDMI
Input Sync Signal
Separate sync: TTL, Positive or Negative Plug & PlayVESA DDC2B
TM
65W maximum, Power management mode: 2W maximum* Power Consumption
Dimensions / Net Weight 566.0× 458.5 × 191.5mm / 22.3 × 18.1 × 7.5 (W×H×D), 6.5kg / 14.3lbs
Upward: 20 degrees  Downward: 5 degrees Viewable angle
Right / Left : 85 degrees each, Up:85 degrees, Down: 75 degrees (Typical)
Maximum Screen Size 518.4mm W × 324.0mm H / 20.4 W × 12.8 H
Power Source100-240VAC, 50/60Hz, 1.5A
Environmental
Considerations
Approvals
TCO ’03, CE, TÜV-GS / MPR3(prEN50279) / ISO 13406-2,
FCC-B, UL / C-UL, VCCI-B, GOST-R Tilt Angle
* Condition: Audio equipment is not connected.
NOTE
Brightness
Contrast ratio250cd/m2 (Typical)
1000 : 1 (Typical), 2000 : 1 (DCR)
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital: HDMI (1.1) Input Video Signal
Input Audio  Signal 0.5Vrms maximum
Speakers 2W × 2 (Stereo speakers)
Input Audio  Connector ø 3.5mm mini jack (Stereo)
Operating: Temperature
Humidity
Storage:
-20 to 60°C / -4 to 140°F
Humidity5 to 35°C / 41 to 95°F
10 to 70% (No condensation)10 to 80% (No condensation)
Temperature
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5427
 
						

							ENGLISH
DIMENSIONS
DIMENSIONS : ProLite B2403WS
566.0mm/22.3520.0mm/20.5
308.0mm/12.1
325.5mm/12.8410.0mm/16.1
70.0mm/2.8
445.0mm/17.5
(575.0mm/22.6)
220.0mm/8.7
(   ): Maximum adjustment range
DIMENSIONS
DIMENSIONS : ProLite E2403WS
566.0mm/22.3520.0mm/20.5
263.0mm/10.4
325.5mm/12.8410.0mm/16.1
70.0mm/2.8
458.5mm/18.1191.5mm/7.5
24     APPENDIX
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5428
 
						

							ENGLISH
M021B01 APPENDIX     25
COMPLIANT TIMING
Dot Clock
  25.175MHz
  31.500MHz
  31.500MHz
  40.000MHz
  49.500MHz
  50.000MHz
  65.000MHz
  75.000MHz
  78.750MHz
  68.250MHz
  79.500MHz
102.250MHz
108.000MHz
108.000MHz
128.000MHz
135.000MHz
106.500MHz
136.750MHz
162.000MHz
146.250MHz
154.000MHz
  25.175MHz
  28.322MHz Vertical
Frequency
59.940Hz
75.000Hz
72.809Hz
60.317Hz
75.000Hz
72.188Hz
60.004Hz
70.069Hz
75.029Hz
60.000Hz
59.870Hz
74.893Hz
75.000Hz
60.020Hz
71.530Hz
75.025Hz
59.887Hz
74.984Hz
60.000Hz
60.000Hz
59.950Hz
70.087Hz
70.087Hz
VGA TEXT
VESA
SVGA VGA
XGA 1024 × 768640 × 480
800 × 600
640 × 350
Video Mode
SXGA
1280 × 10241152 × 864
*1
*1
WXGA1280 × 768
WXGA+ 1440 × 900Horizontal
Frequency
31.469kHz
37.500kHz
37.861kHz
37.879kHz
46.875kHz
48.077kHz
48.363kHz
56.476kHz
60.023kHz
47.396kHz
47.776kHz
60.289kHz
67.500kHz
63.981kHz
75.830kHz
79.976kHz
55.935kHz
70.635kHz
75.000kHz
65.290kHz
74.038kHz
31.469kHz
31.469kHz
UXGA 1600 × 1200
WSXGA+1680 × 1050
WUXGA 1920 × 1200
720 × 400
PC Input
*1 DVI input is not compliant.
*2 Video Input :  480p / 720p / 1080i / 1080p
NOTE
„
D-Sub mini 15pin
Connector
11
1Input Signal
3Red video
8Green video Pin
2
4
5
6
7Pin
Blue video
Green video ground
Blue video ground9
10
12
13
14
15GroundInput Signal
H-Sync
V-Sync
Red video ground
Data line (SDA)*
Clock line (SCL)* GroundNC +5V
NC
* Compliant to VESA DDC.
CONNECTOR PIN ASSIGNMENT
PLB_E2403WS-e-M021B01.P65 2007/09/03, 9:5529