Icom Ic-r5 Communications Reciever Instruction Manual
Have a look at the manual Icom Ic-r5 Communications Reciever Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 Icom manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 37
26
6
SCAN OPERATION
New2001
6
Full/band/programmed scan qSelect VFO mode with [V/M•S.MW•~].
•Select the desired frequency band with [BAND•], if desired.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to 24; programmed scan edges numbers
only displayed)
tTo start the scan, push...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-36.png "Page 37
26
6
SCAN OPERATION
New2001
6
Full/band/programmed scan qSelect VFO mode with [V/M•S.MW•~].
•Select the desired frequency band with [BAND•], if desired.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to 24; programmed scan edges numbers
only displayed)
tTo start the scan, push...")
![Page 38
27
6
SCAN OPERATION
New2001
Scan edges programmingScan edges can be programmed in the same manner as
memory channels. Scan edges are programmed into scan
edges, 00A/00B to 24A/24B, in memory channels.
qPush [V/M•S.MW•~] to select VFO mode.
wSet the desired frequency:
➥Select the desired band with [BAND•].
➥Set the desired frequency with [DIAL].
➥Set other data
(e.g. offset frequency, duplex direction, tone
squelch, etc.)
, if desired.
ePush [V/M•S.MW•~] for 1 sec. to select select memory
write...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-37.png "Page 38
27
6
SCAN OPERATION
New2001
Scan edges programmingScan edges can be programmed in the same manner as
memory channels. Scan edges are programmed into scan
edges, 00A/00B to 24A/24B, in memory channels.
qPush [V/M•S.MW•~] to select VFO mode.
wSet the desired frequency:
➥Select the desired band with [BAND•].
➥Set the desired frequency with [DIAL].
➥Set other data
(e.g. offset frequency, duplex direction, tone
squelch, etc.)
, if desired.
ePush [V/M•S.MW•~] for 1 sec. to select select memory
write...")
![Page 39
28
6
SCAN OPERATION
New2001
6
Memory/bank/all bank scan qSelect memory mode with [V/M•S.MW•~].
•Select the desired bank with [BAND•] for bank scan.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to;
• When memory mode is selected at the step
q q:
- start memory scan.
• When a bank channel is selected at the step q q:
- enter scan type selection mode.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for all bank scan; “BANK” for bank scan.
tPush...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-38.png "Page 39
28
6
SCAN OPERATION
New2001
6
Memory/bank/all bank scan qSelect memory mode with [V/M•S.MW•~].
•Select the desired bank with [BAND•] for bank scan.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to;
• When memory mode is selected at the step
q q:
- start memory scan.
• When a bank channel is selected at the step q q:
- enter scan type selection mode.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for all bank scan; “BANK” for bank scan.
tPush...")
![Page 40
29
6
SCAN OPERATION
New2001
Auto memory write scanThis scan is useful for searching a specified frequency range
and automatically storing busy frequencies into memory
channels. The same frequency ranges used for program scan
are used for auto memory write scan.
qSelect VFO mode with [V/M•S.MW•~].
wPush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
eRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-39.png "Page 40
29
6
SCAN OPERATION
New2001
Auto memory write scanThis scan is useful for searching a specified frequency range
and automatically storing busy frequencies into memory
channels. The same frequency ranges used for program scan
are used for auto memory write scan.
qSelect VFO mode with [V/M•S.MW•~].
wPush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
eRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to...")
![Page 41
30
6
SCAN OPERATION
New2001
6
Memory channels can be set to be skipped for memory skip
scan. In addition, memory channels can be set to be skipped
for both memory skip scan and frequency skip scan. These
are useful to speed up the scan interval.
qSelect a memory channel:
➥Push [V/M•S.MW•~] to select memory mode.
➥Rotate [DIAL] to select the desired channel to be a skip
channel/frequency.
wPush [V/M•S.MW•~] for 1 sec. to enter select memory
write condition.
ePush [MODE•SCAN] several times to select “SKIP”...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-40.png "Page 41
30
6
SCAN OPERATION
New2001
6
Memory channels can be set to be skipped for memory skip
scan. In addition, memory channels can be set to be skipped
for both memory skip scan and frequency skip scan. These
are useful to speed up the scan interval.
qSelect a memory channel:
➥Push [V/M•S.MW•~] to select memory mode.
➥Rotate [DIAL] to select the desired channel to be a skip
channel/frequency.
wPush [V/M•S.MW•~] for 1 sec. to enter select memory
write condition.
ePush [MODE•SCAN] several times to select “SKIP”...")
![Page 42
31
6
SCAN OPERATION
New2001
D D
Scan pause timerThe scan pauses when receiving signals according to the
scan pause time. It can be set from 2–20 sec. or unlimited.
qPush [TS•SET] for 1 sec. to enter set mode.
wRotate [DIAL] to select “EXPAND” item.
eWhile pushing [FUNC], rotate [DIAL] to turn the expand set
mode selection ON.
rRotate [DIAL] to select “PAUSE” item.
tWhile pushing [FUNC], rotate [DIAL] to set the desired
scan pausing time from 2–20 sec. (2 sec. steps) and
“HOLD.”
•“2SEC”–“20SEC”: Scan...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-41.png "Page 42
31
6
SCAN OPERATION
New2001
D D
Scan pause timerThe scan pauses when receiving signals according to the
scan pause time. It can be set from 2–20 sec. or unlimited.
qPush [TS•SET] for 1 sec. to enter set mode.
wRotate [DIAL] to select “EXPAND” item.
eWhile pushing [FUNC], rotate [DIAL] to turn the expand set
mode selection ON.
rRotate [DIAL] to select “PAUSE” item.
tWhile pushing [FUNC], rotate [DIAL] to set the desired
scan pausing time from 2–20 sec. (2 sec. steps) and
“HOLD.”
•“2SEC”–“20SEC”: Scan...")
![Page 44
33
7
PRIORITY WATCH
New2001
Priority watch operationD
D
Memory channel watch and memory scan watchqSelect VFO mode; then, set an operating frequency.
•TV channel can also be selected.
wSet the watching channel(s).
For memory channel watch:
Select the desired memory channel.
For memory scan watch:
Select memory mode, or the desired bank group; then,
push [MODE•SCAN] for 1 sec. to start memory/bank scan.
ePush [TS•SET] for 1 sec. to enter set mode.
rRotate [DIAL] to select “PRIO” item.
tWhile pushing...](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-43.png "Page 44
33
7
PRIORITY WATCH
New2001
Priority watch operationD
D
Memory channel watch and memory scan watchqSelect VFO mode; then, set an operating frequency.
•TV channel can also be selected.
wSet the watching channel(s).
For memory channel watch:
Select the desired memory channel.
For memory scan watch:
Select memory mode, or the desired bank group; then,
push [MODE•SCAN] for 1 sec. to start memory/bank scan.
ePush [TS•SET] for 1 sec. to enter set mode.
rRotate [DIAL] to select “PRIO” item.
tWhile pushing...")
![Page 45
34
7
PRIORITY WATCH
New2001
7
D D
VFO scan watchqSelect memory mode.
•Select a memory bank, if desired.
wPush [MODE•SCAN] for 1 sec. to start memory/bank scan,
if desired.
When scanning memory/bank channels:
Starts memory/bank scan first. Memory/bank scan can-
not be started after VFO scan is started.
ePush [TS•SET] for 1 sec. to enter set mode.
rRotate [DIAL] to select “PRIO” item.
tWhile pushing [FUNC], rotate to turn the priority watch ON.
•Select “BELL” if the priority beep function is necessary....](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-44.png "Page 45
34
7
PRIORITY WATCH
New2001
7
D D
VFO scan watchqSelect memory mode.
•Select a memory bank, if desired.
wPush [MODE•SCAN] for 1 sec. to start memory/bank scan,
if desired.
When scanning memory/bank channels:
Starts memory/bank scan first. Memory/bank scan can-
not be started after VFO scan is started.
ePush [TS•SET] for 1 sec. to enter set mode.
rRotate [DIAL] to select “PRIO” item.
tWhile pushing [FUNC], rotate to turn the priority watch ON.
•Select “BELL” if the priority beep function is necessary....")
![Page 46
35
TONE SQUELCH AND POCKET BEEP
New2001
8Tone/DTCS squelch operationThe tone or DTCS squelch opens only when receiving a sig-
nal with the same pre-programmed subaudible tone or DTCS
code, respectively. You can silently wait for the specified sig-
nal using the same tone.
qSet the desired frequency in FM mode.
wPush [TS•SET] for 1 sec. to enter set mode.
eRotate [DIAL] to select “EXPAND” item.
rWhile pushing [FUNC], rotate [DIAL] to turn the expanded
set mode ON.
tRotate [DIAL] to select “TSQL” item....](http://img.usermanuals.tech/thumb/2452/82812/w64_icom_r5-wideband-scanner-reciever_manual_d-45.png "Page 46
35
TONE SQUELCH AND POCKET BEEP
New2001
8Tone/DTCS squelch operationThe tone or DTCS squelch opens only when receiving a sig-
nal with the same pre-programmed subaudible tone or DTCS
code, respectively. You can silently wait for the specified sig-
nal using the same tone.
qSet the desired frequency in FM mode.
wPush [TS•SET] for 1 sec. to enter set mode.
eRotate [DIAL] to select “EXPAND” item.
rWhile pushing [FUNC], rotate [DIAL] to turn the expanded
set mode ON.
tRotate [DIAL] to select “TSQL” item....")
30 6 SCAN OPERATION New2001 6 Memory channels can be set to be skipped for memory skip scan. In addition, memory channels can be set to be skipped for both memory skip scan and frequency skip scan. These are useful to speed up the scan interval. qSelect a memory channel: ➥Push [V/M•S.MW•~] to select memory mode. ➥Rotate [DIAL] to select the desired channel to be a skip channel/frequency. wPush [V/M•S.MW•~] for 1 sec. to enter select memory write condition. ePush [MODE•SCAN] several times to select “SKIP” item. •While pushing [MODE•SCAN], rotating [DIAL] can also select “SKIP” item. rWhile pushing [FUNC], rotate [DIAL] to select the skip con- dition from “SKIP,” “PSKIP” or “OFF” for the selected chan- nel. •SKIP : The channel is skipped during memory or bank scan. •PSKIP : The channel is skipped during memory/bank scan and the programmed frequency is skipped during VFO scan, such as programmed scan. •OFF : The channel or programmed frequency is scanned dur- ing any scan. tPush [MODE•SCAN] several times, or while pushing and holding [MODE•SCAN] rotate [DIAL] to select “S.MW” item. yPush [V/M•S.MW•~] for 1 sec. to set the skip condition. •“SKIP” or “P SKIP” indicator appears, according to the skip se- lection in the step r. ✔CONVENIENT! The skip setting can also be set with the following operation for easy setting. qSelect the desired memory channel to be set as a skip channel/frequency. wWhile pushing [FUNC], push [V/M•S.MW•~] to select theskip condition from “SKIP,” “P SKIP” and “OFF (no indication) .” FM SKIPP FM SKIP • Skip channel setting • Program skip setting “SKIP” appears “P SKIP” appears [MODE•SCAN][DIAL] • Skip setting Skip channel/frequency setting IC-R5_1.qxd 02.10.23 11:29 Page 30 (1,1)
31 6 SCAN OPERATION New2001 D D Scan pause timerThe scan pauses when receiving signals according to the scan pause time. It can be set from 2–20 sec. or unlimited. qPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select “EXPAND” item. eWhile pushing [FUNC], rotate [DIAL] to turn the expand set mode selection ON. rRotate [DIAL] to select “PAUSE” item. tWhile pushing [FUNC], rotate [DIAL] to set the desired scan pausing time from 2–20 sec. (2 sec. steps) and “HOLD.” •“2SEC”–“20SEC”: Scan pauses 2–20 sec. while receiving a sig- nal. •“HOLD”: Scan pauses on a received a signal until it disappears. yPush [TS•SET] to exit set mode. D D Scan resume timerThe scan re-starts after a signal disappears according to the resume time. it can be set from 0–5 sec. or unlimited. qPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select “EXPAND” item. eWhile pushing [FUNC], rotate [DIAL] to turn the expand set mode selection ON. rRotate [DIAL] to select “RESUME” item. tWhile pushing [FUNC], rotate [DIAL] to set the desired scan pausing time from 0–5 sec. (1 sec. steps) and “HOLD.” •“0SEC”: Scan restarts immediately after the signal dis- appears. •“1SEC”–“5SEC”: Scan restarts 1–5 sec. after the signal disap- pears. •“HOLD”: Scan restarts by rotating [DIAL] only. yPush [TS•SET] to exit set mode. [TS•SET][FUNC][DIAL]• Resume timer setting Setting indicationAfter 1 sec. [TS•SET][FUNC][DIAL]• Pause timer setting Setting indicationAfter 1 sec. Scan resume condition USING EXPANDED SET MODE IC-R5_1.qxd 02.10.23 11:29 Page 31 (1,1)
32 7 PRIORITY WATCH 67 Priority watch typesPriority watch checks for signals on a frequency every 5 sec. while operating on a VFO frequency or scanning. The re- ceiver has 3 priority watch types to suit your needs. The watch resumes according to the selected scan resume condition. See the left page for details. NOTES: If the pocket beep function is activated, the receiver auto- matically selects the tone squelch function when priority watch starts.D D About priority beep functionWhen receiving a signal on the priority frequency, you can be alerted with beeps and a blinking “S.” This function can be activated when setting the priority watch function ON. MEMORY CHANNEL WATCHWhile operating on a VFO fre- quency, priority watch checks for a signal on the selected memory channel every 5 sec.•A memory channel with skip infor- mation can be watched.MEMORY SCAN WATCHWhile operating on a VFO fre- quency, priority watch checks for signals on each memory chan- nel in sequence.•The memory skip function and/or memory bank scan is useful to speed up the scan. 5 sec. VFO frequencyMemory channel5 sec.VFO frequency SKIP Mch 000Mch 001Mch 001Mch 999 VFO SCAN WATCHWhile scanning on VFO mode, priority watch checks for signals on the selected memory chan- nel every 5 sec. 5 sec. VFO scanMemory channel IC-R5_1.qxd 02.10.23 11:29 Page 32 (1,1)
33 7 PRIORITY WATCH New2001 Priority watch operationD D Memory channel watch and memory scan watchqSelect VFO mode; then, set an operating frequency. •TV channel can also be selected. wSet the watching channel(s). For memory channel watch: Select the desired memory channel. For memory scan watch: Select memory mode, or the desired bank group; then, push [MODE•SCAN] for 1 sec. to start memory/bank scan. ePush [TS•SET] for 1 sec. to enter set mode. rRotate [DIAL] to select “PRIO” item. tWhile pushing [FUNC], rotate to turn the priority watch ON. •Select “BELL” if the priority beep function is necessary. yPush [TS•SET] to exit set mode and start the watch. •“PRIO” indicator appears. •The receiver checks the memory/bank channel(s) every 5 sec. •The watch resumes according to the selected scan resume con- dition. (p. 31) uPush [TS•SET] to cancel the watch. FM SKIPP PRIO FM PRIO FM SKIPP PRIO FM PRIO • During priority watchMonitors VFO frequency for 5 sec.Pauses on a memory (bank) channel when a signal is received. • During priority watch with priority beepEmits beep and blinks “S” indicator when a signal is received on a memory (bank) channel. [TS•SET][FUNC][DIAL]• Priority setting item • Priority ON • Priority beep ON IC-R5_1.qxd 02.10.23 11:29 Page 33 (1,1)
34 7 PRIORITY WATCH New2001 7 D D VFO scan watchqSelect memory mode. •Select a memory bank, if desired. wPush [MODE•SCAN] for 1 sec. to start memory/bank scan, if desired. When scanning memory/bank channels: Starts memory/bank scan first. Memory/bank scan can- not be started after VFO scan is started. ePush [TS•SET] for 1 sec. to enter set mode. rRotate [DIAL] to select “PRIO” item. tWhile pushing [FUNC], rotate to turn the priority watch ON. •Select “BELL” if the priority beep function is necessary. yPush [TS•SET] to exit set mode and start the watch. •“PRIO” indicator appears. uPush [MODE•SCAN] for 1 sec. to enter scan type selection condition. iRotate [DIAL] to select the desired scan type from “ALL,” “BAND” and “PROGxx (xx= 0–24) .” oPush [MODE•SCAN] to start the VFO scan watch. •The receiver checks the memory channel(s) every 5 sec. •The watch resumes according to the selected scan resume con- dition. (p. 31) !0Push [TS•SET] to cancel the watch and scan. FM SKIPP PRIO FM PRIO FM SKIPP PRIO FM PRIO • During VFO scan watchSearches VFO frequen- cies for 5 sec.Pauses on a memory (bank) channel when a signal is received. • During VFO scan watch with priority beepEmits beep and blinks “S” indicator when a signal is received on a memory (bank) channel. IC-R5_1.qxd 02.10.23 11:29 Page 34 (1,1)
35 TONE SQUELCH AND POCKET BEEP New2001 8Tone/DTCS squelch operationThe tone or DTCS squelch opens only when receiving a sig- nal with the same pre-programmed subaudible tone or DTCS code, respectively. You can silently wait for the specified sig- nal using the same tone. qSet the desired frequency in FM mode. wPush [TS•SET] for 1 sec. to enter set mode. eRotate [DIAL] to select “EXPAND” item. rWhile pushing [FUNC], rotate [DIAL] to turn the expanded set mode ON. tRotate [DIAL] to select “TSQL” item. yWhile pushing [FUNC], rotate [DIAL] to select the desired subaudible tone condition from “TSQL,” “P BEEP,” “DTCS,” “P DTCS” and “OFF.”uPush [TS•SET] to exit set mode. •One of “TSQL,” TSQLS,” “DTCS” or “SDTCS” appears ac- cording to the tone selection in the step y.iWhen a signal with the matched tone is received, the squelch opens and the receiver emits audio. When pocket beep function is activated, the receiver also emits beep tones and blinks “S”.•Beep tones sound and “S” blinks for 30 sec.oPush [FUNC] to stop the beeps and blinking manually.•“S” disappears and the pocket beep function is deactivated.!0To cancel the tone squelch or DTCS, select “OFF” with the “TSQL” item in the expanded set mode, as described in the step y. FM SQL SKIPTP FM SQL SKIPTP FM DTCS SKIPP FM DTCS SKIPP Tone squelch selection Tone squelch with pocket beep function selection DTCS selection DTCS with pocket beep function selection Tone squelch selection Tone squelch with pocket beep function selection DTCS selection DTCS with pocket beep function selection IC-R5_1.qxd 02.10.23 11:29 Page 35 (1,1)
36 8 TONE SQUELCH AND POCKET BEEP New2001 8 Tone squelch frequency/DTCS code setting88.5 Hz and 023 is set as the default for the tone squelch fre- quency and the DTCS code, respectively. The frequency and code can be selected as desired. qPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select “EXPAND” item. eWhile pushing [FUNC], rotate [DIAL] to turn the expanded set mode ON. rRotate [DIAL] to select “TONE” item when selecting the tone squelch frequency; select “CODE” item when select- ing the DTCS code. tWhile pushing [FUNC], rotate [DIAL] to select the desired subaudible tone frequency or DTCS code.•See the tables at right.yPush [TS•SET] to exit set mode.•Available tone frequency list NOTE:The receiver has 50 tone frequencies and conse- quently their spacing is narrow compared to units having 38 tones. Therefore, some tone frequencies may receive interference from adjacent tone frequencies. •Available DTCS code list 023 025 026 031 032 036 043 047 051 053125 131 132 134 143 145 152 155 156 162245 246 251 252 255 261 263 265 266 271356 364 365 371 411 412 413 423 431 432506 516 523 526 532 546 565 606 612 624 054 065 071 072 073 074 11 4 11 5 11 6 122165 172 174 205 212 223 225 226 243 244274 306 311 315 325 331 332 343 346 351445 446 452 454 455 462 464 465 466 503627 631 632 654 662 664 703 712 723 731 732 734 743 754 67.0 69.3 71.9 74.4 77.079.7 82.5 85.4 88.5 91.594.8 97.4 100.0 103.5 107.2110.9 114.8 118.8 123.0 127.3131.8 136.5 141.3 146.2 151.4156.7 159.8 162.2 165.5 167.9171.3 173.8 177.3 179.9 183.5186.2 189.9 192.8 196.6 199.5203.5 206.5 210.7 218.1 225.7229.1 233.6 241.8 250.3 254.1 Tone squelch frequency selection DTCS code selectionAfter 1 sec. After 1 sec. IC-R5_1.qxd 02.10.23 11:29 Page 36 (1,1)
37 8 TONE SQUELCH AND POCKET BEEP New2001 DTCS polarity settingAs well as the code setting, the polarity setting is also avail- able for the DTCS operation. When a different polarity is set, the DTCS never releases audio mute even a signal with matched code number is received. qPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select “EXPAND” item. eWhile pushing [FUNC], rotate [DIAL] to turn the expanded set mode ON. rRotate [DIAL] to select “DTCS P” item.tWhile pushing [FUNC], rotate [DIAL] to select the polarity from normal (NORMAL) and reverse (REV). yPush [TS•SET] to exit set mode. Normal polarity Reverse polarity After 1 sec. [TS•SET][FUNC][DIAL] IC-R5_1.qxd 02.10.23 11:29 Page 37 (1,1)
38 8 TONE SQUELCH AND POCKET BEEP New2001 8 Tone scanBy monitoring a signal that is being operated with pocket beep, tone or DTCS squelch function, you can determine the tone frequency or DTCS code necessary to open a squelch. qSet the frequency to be checked for a tone frequency or code. wTurn the desired tone type, tone squelch or DTCS, ON in expanded set mode.•One of “TSQL” or “DTCS” appears. •Even the pocket beep function is activated, the function is can- celled when starts the tone scan.eWhile pushing [FUNC], push [MODE•SCAN] to start the tone scan.•To change the scanning direction, rotate [DIAL]. rWhen the CTCSS tone frequency or 3-digit DTCS code is matched, the squelch opens and the tone frequency or code is temporarily programmed into the selected condi- tion, such as memory channel.•The tone scan pauses when a CTCSS tone frequency or 3-digit DTCS code is detected.✔ For your convenient! Even no tone type is selected, either tone squelch or DTCS, pushing [MODE•SCAN] while pushing and holding [FUNC] also start tone scan. In this case, the tone scan searching for tone squelch frequency only.NOTE:The decoded tone frequency or code is pro- grammed temporarily when a memory channel is se- lected. However, this will be cleared when the memory channel is re-selected. DTCS scan Tone squelch scan [MODE•SCAN][FUNC] IC-R5_1.qxd 02.10.23 11:29 Page 38 (1,1)
39 SET MODE New2001 9GeneralSet mode is used for programming infrequently changed val- ues or conditions of functions. In addition, the IC-R5 has an expanded set mode which is used for programming even more infrequently changed val- ues or conditions of functions. When turning the expanded set mode OFF, only half of the set mode items are displayed for simple operation.D D Set mode entering and operationqPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select the desired item. eWhile pushing [FUNC], rotate [DIAL] to select the desired value or condition. rPush [TS•SET] to exit set mode, or rotate [DIAL] to select another set mode item. D D Expanded set mode ON/OFFqPush [TS•SET] for 1 sec. to enter set mode. wRotate [DIAL] to select “EXPAND” item. eWhile pushing [FUNC], rotate [DIAL] to turn the expanded set mode ON and OFF. rRotate [DIAL] to select the desired item. tWhile pushing [FUNC], rotate [DIAL] to select the desired value or condition. yPush [TS•SET] to exit set mode, or rotate [DIAL] to select another item. Expanded set mode OFF Expanded set mode ON [TS•SET][FUNC][DIAL] IC-R5_1.qxd 02.10.23 11:29 Page 39 (1,1)