Icom Ic-4088a Frs Uhf Fm Transceiver Instruction Manual
Here you can view all the pages of manual Icom Ic-4088a Frs Uhf Fm Transceiver Instruction Manual. The Icom manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 11
5 3 BATTERY CHARGING 23 Battery cautionCAUTION NEVERshort the terminals. NEVERmix old and new batteries. NEVERincinerate used battery cells. Internal battery gas may cause explosion. Make sureall battery cells are the same brand, type and capacity. AVOID over charging— The BP-202 can be charged during oper- ation when the AC adapter or the optional cigarette lighter cable is connected. To prevent over charging, the IC-4088A has charging timer that automatically disconnecting the charging line...
Page 12
6 3 BATTERY CHARGING Charging connectionsD DRegular charging with the BC-149A, CP-18A➥Connect the optional BC-149A AC ADAPTER or CP-18A CIGARETTE LIGHTER CABLE to [DC 6V]. •Charging period: approx. 15 hours IMPORTANT!: Use the BC-149A or CP-18AONLY. Other type of AC adapter, cigarette lighter cable or DC power cable with an external power supply may damage the transceiver. The optional BP-202 can only be charged— other AA (R6) size rechargeable Ni-Cd cannot be charged. BE SUREto disconnect the CP-18A...
Page 13
7 3 BATTERY CHARGING 3 D DRapid charging with the BC-119N+AD-105qInsert the optional AD-105 DESKTOP CHARGER ADAPTER into the charging slot of the BC-119N. wInsert the battery pack, either by itself or attached to the trans- ceiver, into the charger. IC-4088ABP-202 AD-105 BC-119N AC adapter NOT used: Fix the 3-pin connector to the bottom of the charger with the adhesive tape, etc., to prevent catching or touching the 3-pin connector’s terminals with the adapter’s leads, etc.* *NOTE: Put the Ni-Cd...
Page 14
8 4 BASIC OPERATION Power ON➥Push [PWR] for 1 sec. to turn the power ON.•“ ” and operating channel num- ber appear on the display.Adjusting the volumeqPush and hold [MODE] for 1 sec. to open the squelch (monitor function ON).•“ ” indicator appears on the dis- play while the squelch is open.wAdjust the audio to a suitable level using [ VOL ]. ePush and hold [MODE] for 1 sec. to close the squelch. ✔What is squelch?A squelch circuit allows muting of undesired noise while receiving no signal and emit audio...
Page 15
9 4 BASIC OPERATION 4 Selecting the operating channelPush [Y] or [Z] keys several times until the desired operating channel number appears on the display. •While pushing and holding [Y] or [Z] keys, the displayed channel changes continuously until chan- nel number “1” appears. To keep the automatic selection, release the [Y] or [Z] keys then push and hold them again. •When displayed channel stops at channel number “1,” a beep is emitted. NOTE: •The transceiver has 14 operating frequency channels. • The...
Page 16
10 5 RECEIVE AND TRANSMIT qSelect the desired operating channel with [Y]/[Z]. When a signal is received: • “” indicator appears on the display. •Squelch opens and audio is emitted from the speaker. - Further adjustment of [VOL] may be necessary at this point. wPush and hold [PTT] to transmit then speak into the microphone.•Do not hold the transceiver too close to your mouth or speak too loudly. This may distort the sig- nal. •The transmit indicator “” ap- pears on the display.eRelease [PTT] to return to...
Page 17
11 5 RECEIVE AND TRANSMIT 5 ✔Talk Range The IC-4088A is designed to maximize performance and improve transmission range in the field. However, the single most impor- tant factor in transmit range (talk power) is the surrounding envi- ronment. These radios are “line of sight” radios and as such, transmission range are influenced by the degree to which you can “see” the other communicating party. Large concrete struc- tures and heavy foliage or transmission from inside a building or vehicle will reduce the...
Page 18
12 6 GROUP MODE (CTCSS) Setting the group codeThe IC-4088A is equipped with 38 group codes. Group mode oper- ation provides communication with silent standby since you will only receive calls from group members using the same group number. First of all, set the same group code number for all group member’s transceivers. To turn ON the group mode op- eration: qPush [MODE] to enter set mode.•“---” (group mode OFF) appears on the display. wPush [Y] or [Z] to select the de- sired code number. ePush [MODE]...
Page 19
13 6 GROUP MODE (CTCSS) 6 D D CTCSS code table (unit: Hz) CH Freq. CH Freq. CH Freq. CH Freq. 01 67.0 11 97.4 21 136.5 31 192.8 02 71.9 12 100.0 22 141.3 32 203.5 03 74.4 13 103.5 23 146.2 33 210.7 04 77.0 14 107.2 24 151.4 34 218.1 05 79.7 15 110.9 25 156.7 35 225.7 06 82.5 16 114.8 26 162.2 36 233.6 07 85.4 17 118.8 27 167.9 37 241.8 08 88.5 18 123.0 28 173.8 38 250.3 09 91.5 19 127.3 29 179.9---OFF 10 94.8 20 131.8 30 186.2 ✔What is CTCSS (Continuous Tone Coded Squelch System) GROUP MODE ? CTCSS...
Page 20
14 7 SCAN FUNCTION Scanning is an efficient way to locate signals quickly over all chan- nels. Select scan resume condition in advance, using Initial Set Mode (p. 17)DStarting the scan➥While pushing [Y], push [Z] to start the scan. • “-” flashes. • While pushing [Z], pushing [Y] also starts the scan. • Push [Z] or [Y] to change the scanning direction or resume the scan manually. • To cancel the scan, push [Z] (or [Y]) while [Y] (or [Z]) is pushed, or push [PTT]. CH 14 CH 3 CH 2 CH 1 CH 4 CH 5 [Z][Y]...