IBM Projector M400 User Manual

							Operating
 
range
 
This
 
remote
 
control
 
uses
 
infrared
 
transmission
 
to
 
control
 
the
 
projector.
 
It
 
is
 
not
 
necessary
 
to
 
point
 
the
 
remote
 
directly
 
at
 
the
 
projector.
 
Provided
 
you
 
are
 
not
 
holding
 
the
 
remote
 
to
 
the
 
sides
 
or
 
the
 
rear
 
of
 
the
 
projector,
 
the
 
remote
 
will
 
function
 
within
 
a
 
maximum
 
radius
 
of
 
7m
 
(22ft)
 
and
 
30°
 
above
 
or
 
below
 
the
 
projector
 
level.
 
If
 
the
 
projector
 
does
 
not
 
respond
 
to
 
the
 
remote
 
control,
 
move
 
a
 
little
 
closer.
 
Note:
   
Yo u
 
can
 
also
 
point
 
the
 
remote
 
at
 
the
 
projected
 
image.
 
Projector
 
and
 
remote
 
control
 
buttons
 
The
 
projector
 
can
 
be
 
operated
 
using
 
the
 
remote
 
control
 
or
 
the
 
buttons
 
on
 
the
 
top
 
of
 
the
 
projector.
 
All
 
operations
 
can
 
be
 
carried
 
out
 
with
 
the
 
remote
 
control.
 
The
 
figure
 
below
 
shows
 
the
 
corresponding
 
buttons
 
on
 
the
 
remote
 
control
 
and
 
on
 
the
 
projector
 
for
 
OSD
 
menu
 
operation.
 
1
2
/
/
   
  

1
 
Menu
 

2
 
Source/Left
 
button
 

3
 
Quick
 
menu/Down
 
button
 

4
 
Auto/Right
 
button
 

5
 
Up
 
button
 

6
 
Auto/Enter
 
button
   
Chapter
 
4.
 
Using
 
the
 
projector
 
features
 
4-3 
						

							4-4
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Chapter
 
5.
 
On-Screen
 
Display
 
menu
 
controls
 
This
 
projector
 
has
 
an
 
On-Screen
 
Display
 
(OSD)
 
that
 
lets
 
you
 
make
 
image
 
adjustments
 
and
 
change
 
various
 
settings.
 
Note:
   
Yo u
 
must
 
have
 
a
 
display
 
on
 
the
 
screen
 
in
 
order
 
to
 
access
 
the
 
OSD.
 
Navigating
 
the
 
OSD
 
Yo u
 
can
 
use
 
the
 
remote
 
control
 
or
 
the
 
buttons
 
on
 
the
 
top
 
of
 
the
 
projector
 
to
 
navigate
 
and
 
make
 
changes
 
to
 
the
 
OSD.
 
The
 
following
 
sections
 
show
 
the
 
menus
 
in
 
the
 
OSD.
 
Image
 
menu
 
The
 
image
 
menu
 
can
 
be
 
found
 
through
 
the
 
main
 
menu.
 
To
 
access
 
the
 
Image
 
menu,
 
follow
 
these
 
steps:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
Image
 
menu.
 
3.
 
 
 
Press
 
the
 
cursor
 
down
 
button
 
to
 
move
 
down
 
in
 
the
 
Image
 
menu.
 
The
 
Image
 
menu
 
is
 
shown
 
below.
  
 
 
The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
Image
 
menu
 
and
 
the
 
default.
  
Item
 
Description
 
Default
 
Brightness
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
brightness.
 
Range:
 
-50
 
to
 
50
 
0
  
©
 
Copyright
 
IBM
 
Corp.
 
2004
 
5-1  
						

							Item
 
Description
 
Default
 
Contrast
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
contrast.
 
Range:
 
-50
 
to
 
50
 
0
 
Picture
 
Adjustment
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
A/D
 
sampling
 
number.
 
Range:
 
-50
 
to
 
50
 
0
 
Fine
 
Picture
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
A/D
 
sampling
 
clock.
 
Range:
 
-50
 
to
 
50
 
Auto-detected
 
H
 
Position
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
the
 
image
 
left
 
or
 
right.
 
Range:
 
-50
 
to
 
50
 
0
 
V
 
Position
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
the
 
image
 
up
 
or
 
down.
 
Range:
 
-50
 
to
 
50
 
0
 
Color
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
video
 
saturation.
 
Range:
 
-50
 
to
 
50
 
0
 
Tint
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
video
 
hue.
 
Range:
 
-50
 
to
 
50
 
0
 
Sharpness
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
video
 
sharpness.
 
Range:
 
-50
 
to
 
50
 
0
 
Cancel
 
Press
 
the
 
enter
 
button
 
to
 
reset
 
Brightness,
 
Contrast,
 
Picture
 
Adjust,
 
H
 
Position,
 
V
 
Position,
 
Color,
 
Tint,
 
and
 
Sharpness
 
to
 
default
 
values.
 
0
   
 
Color
 
menu
 
To
 
access
 
the
 
Color
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
Color
 
menu.
   
5-2
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							3.
   
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
within
 
the
 
Color
 
menu.
 
The
 
color
 
menu
 
is
 
shown
 
below.
  
 
 
The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
Color
 
menu
 
and
 
the
 
default.
  
Item
 
Description
 
Default
 
Quick
 
Color
 
Adj.
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
Color
 
Adjust.
 
Range:
 
Standard/Color/Custom
 
Standard
 
Gamma
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
Gamma
 
Correction.
 
Range:
 
Normal/Natural/Real
 
Normal
 
Color
 
Temperature
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
color
 
temperature.
 
Range:
 
Low/Middle/Normal/High
 
Normal
 
White
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
white
 
segment.
 
Range:
 
Low/Middle/High
 
RGB:
 
High
 
Video:
 
Low
 
White
 
Balance
 
Change
 
White
 
Balance
 
Menu
 
N/A
 
Color
 
Space
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
color
 
space.
 
Range:
 
BT.709/SMPTE240
 
BT.709
 
Cancel
 
Reset
 
Quick
 
Color
 
Adj.,
 
Gamma,
 
Color
 
Temp.,
 
White,
 
and
 
Color
 
Space
 
to
 
default
 
value.
 
N/A
 
   
Chapter
 
5.
 
On-Screen
 
Display
 
menu
 
controls
 
5-3 
						

							View
 
menu
 
To
 
access
 
the
 
View
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
   
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
View
 
menu.
 
3.
 
 
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
up
 
and
 
down
 
in
 
the
 
View
 
menu.
 
The
 
View
 
menu
 
is
 
shown
 
below.
  
 
 
The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
View
 
menu
 
and
 
the
 
default.
  
Item
 
Description
 
Default
 
Aspect
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
aspect
 
ratio.
 
RGB
 
Range:
 
Auto/Direct/Rear
 
Video
 
Range:
 
Auto/Wide/Zoom
 
Auto
 
Filter
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
scaling
 
filter.
 
Range:
 
1
 
to
 
5
 
3
 
Vertical
 
Flip
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
vertical
 
flip.
 
Range:
 
Off/On
 
Off
 
Horizontal
 
Flip
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
horizontal
 
flip.
 
Range:
 
Off/On
 
Off
 
Keystone
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
adjust
 
the
 
display
 
keystone.
 
Range:
 
-50
 
to
 
50
 
0
   
5-4
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Item
 
Description
 
Default
 
Keystone
 
Save
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
keystone
 
save.
 
Range:
 
Off/On
 
On
 
Digital
 
Zoom
 
Digital
 
Zoom
 
N/A
 
Panning
 
Use
 
the
 
↑,→,↓,←
 
buttons
 
to
 
pan
 
in
 
the
 
Digitally
 
zoomed
 
image.
 
N/A
 
Cancel
 
Reset
 
Aspect,
 
Filter,
 
Vertical
 
Flip,
 
Horizontal
 
Flip,
 
Keystone,
 
and
 
Keystone
 
Save
 
to
 
default
 
values.
 
N/A
 
 
 
Setup
 
menu
 
To
 
access
 
the
 
View
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
left/right
 
cursor
 
to
 
move
 
to
 
the
 
Setup
 
menu.
 
3.
 
 
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
up
 
and
 
down
 
in
 
the
 
Setup
 
menu.
 
The
 
Setup
 
menu
 
is
 
shown
 
below.
  
 
 
The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
Setup
 
menu
 
and
 
the
 
default.
  
Item
 
Description
 
Default
 
Auto
 
Source
 
Press
 
the
 
cursor
 
right/left
 
button
 
to
 
select.
 
This
 
will
 
automatically
 
search
 
all
 
of
 
the
 
input
 
ports.
 
Range:
 
On/Off
 
On
   
Chapter
 
5.
 
On-Screen
 
Display
 
menu
 
controls
 
5-5 
						

							Item
 
Description
 
Default
 
Auto
 
Power
 
Off
 
Press
 
the
 
cursor
 
right/left
 
button
 
to
 
select.
 
This
 
will
 
automatically
 
turn
 
off
 
the
 
lamp
 
when
 
there
 
is
 
no
 
signal
 
to
 
the
 
projector
 
for
 
5
 
minutes.
 
Range:
 
On/Off
 
Off
 
Menu
 
Position
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
different
 
OSD
 
locations.
 
Range:
 
Left/Top/Center/Right/Bottom
 
Center
 
Input
 
Format
 
Change
 
the
 
input
 
format
 
menu.
 
Auto
 
Presentation
 
Timer
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
the
 
time
 
for
 
the
 
presentation
 
timer.
 
Range:
 
Off/10
 
min/20
 
min/30
 
min/40
 
min/50
 
min/60
 
min
 
Off
 
Cancel
 
Reset
 
Auto
 
Source,
 
Auto
 
Power
 
off,
 
Menu
 
Position,
 
and
 
Presentation
 
Timer
 
to
 
default
 
values.
 
N/A
   
 
Option
 
menu
 
To
 
access
 
the
 
Option
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
Option
 
menu.
 
3.
 
 
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
up
 
and
 
down
 
within
 
the
 
Option
 
menu.
 
The
 
Option
 
menu
 
is
 
shown
 
below.
  
 
   
5-6
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
Option
 
menu
 
and
 
the
 
default.
  
Item
 
Description
 
Default
 
Language
 
Change
 
the
 
Language
 
Range:
 
English/German/French/Italian/
 
Spanish/Swedish/Korean
 
/Simplified
 
Chinese/
 
Traditional
 
Chinese/Japanese
 
English
 
On
 
Screen
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
the
 
on-screen
 
menu.
 
Range:
 
On/Off
 
On
 
Background
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
background
 
color.
 
Range:
 
Blue/Black
 
Blue
 
Startup
 
Screen
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
select
 
the
 
startup
 
screen.
 
Range:
 
Logo/Blank
 
Logo
 
Cancel
 
Preset
 
On
 
Screen,
 
Background,
 
and
 
Startup
 
Screen
 
to
 
default
 
values.
 
N/A
   
 
Information
 
menu
 
To
 
access
 
the
 
Information
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
Info
 
menu.
   
Chapter
 
5.
 
On-Screen
 
Display
 
menu
 
controls
 
5-7 
						

							3.
   
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
up
 
and
 
down
 
in
 
the
 
Info
 
menu.
 
The
 
Info
 
menu
 
is
 
shown
 
below.
  
 
 
The
 
following
 
table
 
shows
 
the
 
options
 
that
 
you
 
will
 
see
 
in
 
the
 
Info
 
menu.
  
Item
 
Description
 
Factory
 
Default
 
Change
 
factory
 
default
 
message
 
menu.
 
Lamp
 
Timer
 
Reset
 
Reset
 
the
 
lamp
 
timer.
 
Resolution
 
Shows
 
Resolution
 
H/V
 
format.
 
Frequency
 
Shows
 
Frequency
 
H/V
 
information.
 
Lamp
 
Timer
 
Shows
 
lamp
 
hours
 
used
 
information.
 
Version
 
Shows
 
Firmware
 
version
 
information.
 
 
 
Sub
 
Menus
 
This
 
section
 
describes
 
the
 
different
 
sub
 
menus
 
in
 
depth.
 
White
 
Balance
 
White
 
Balance
 
is
 
a
 
menu
 
for
 
calibration
 
purposes.
 
Follow
 
the
 
steps
 
below
 
to
 
use
 
the
 
White
 
Balance
 
menu.
 
1.
 
 
 
Start
 
by
 
finding
 
a
 
black
 
pattern
 
source
 
from
 
the
 
computer.
  
 
 
   
5-8
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide