IBM Projector M400 User Manual

Chapter
 
2.
 
Setting
 
up
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
positioning
 
the
 
projector,
 
connecting
 
a
 
computer
 
source,
 
using
 
the
 
projector
 
with
 
Microsoft
 
Windows,
 
and
 
displaying
 
and
 
adjusting
 
a
 
computer
 
source
 
image.
 
Starting
 
and
 
shutting
 
down
 
the
 
projector
 
Please
 
follow
 
the
 
steps
 
below
 
to
 
start
 
your
 
projector,
 
and
 
to
 
shut
 
off
 
the
 
projector.
   
Attention:
 
 
Before
 
moving
 
the...

Note:
   
Leave
 
the
 
power
 
cable
 
plugged
 
in
 
for
 
at
 
least
 
2-5
 
minutes
 
until
 
the
 
projector
 
returns
 
to
 
room
 
temperature
 
before
 
placing
 
the
 
projector
 
inside
 
the
 
soft
 
case.
 
Placing
 
the
 
projector
 
into
 
the
 
case
 
too
 
soon
 
after
 
switching
 
off
 
the
 
power
 
could
 
cause
 
the
 
projector
 
to
 
overheat.
Attention:
   
Before
 
moving
 
the
 
projector,
 
be
 
sure
 
to
 
power
 
down
 
the
 
projector
 
normally
 
and
 
disconnect
 
the...

Table
 
2-1.
 
Zoom
 
lens
 
operation
 
range
 
(m/ft)
 
Diagonal
 
screen
 
size
    
(m/in.)
 
Image
 
Width
  
 
(m/ft)
 
Image
 
height
  
 
(m/ft)
 
Distance
 
from
 
center
 
of
 
lens
 
to
 
bottom
 
of
 
image
  
 
(m/ft)
 

1-
 
to
 
1.20/-
 
to
 
3.94
 
0.66/26
 
0.53/1.74
 
0.40/1.31
 
0.07/0.23
 

21.54
 
to
 
1.85/5.05
 
to
 
6.07
 
1.02/40
 
0.81/2.66
 
0.61/2
 
0.11/0.36
 

32.33
 
to
 
2.80/7.64
 
to
 
9.19
 
1.52/60
 
1.22/4
 
0.91/2.99
 
0.16/0.52
 

43.12
 
to
 
3.75/10.24
 
to...

Note:
   
v
 
 
 
The
 
projector
 
table
 
or
 
stand
 
should
 
be
 
level
 
and
 
sturdy.
 
v
 
 
 
Position
 
the
 
projector
 
so
 
that
 
it
 
is
 
perpendicular
 
to
 
the
 
screen.
 
v
 
 
 
Be
 
sure
 
cables
 
are
 
not
 
in
 
a
 
place
 
where
 
they
 
can
 
cause
 
the
 
projector
 
to
 
be
 
knocked
 
over.
Adjusting
 
the
 
image
 
To
 
adjust
 
the
 
zoom,
 
focus,
 
and
 
keystone
 
for
 
the
 
image,
 
complete
 
the
 
following
 
steps:
 
1.
 
 
 
Twist
 
the
 
rings
 
on
 
the...

The
 
keystone
 
control
 
appears
 
on
 
the
 
OSD,
 
as
 
shown.
    
 
To
 
adjust
 
the
 
keystone
 
on
 
the
 
projector,
 
press
 
Quick
 
Menu
 
and
 
select
 
the
 
keystone
 
submenu;
 
then
 
use
 
the
 
left/right
 
buttons
 
to
 
adjust
 
the
 
keystone.
Image
 
resolution
 
The
 
XGA
 
resolution
 
of
 
the
 
projected
 
image
 
is
 
1024
 
x
 
768
 
(XGA).
 
The
 
projector
 
is
 
compatible
 
with
 
screen
 
resolutions
 
up
 
to
 
1280
 
x
 
1024
 
(SXGA).
 
If
 
your
 
computer
 
screen...

2-6
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 

Chapter
 
3.
 
Connecting
 
devices
 
to
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
connecting
 
devices
 
to
 
the
 
M400
 
projector.
 
Connecting
 
devices
 
Computers
 
and
 
video
 
devices
 
can
 
be
 
connected
 
to
 
the
 
projector
 
at
 
the
 
same
 
time.
 
Check
 
the
 
user ’s
 
manual
 
of
 
the
 
connecting
 
device
 
to
 
confirm
 
that
 
it
 
has
 
the
 
appropriate
 
output
 
connector.
    
  

1
 
USB
 
slot
 

2
 
Audio
 

3
 
Video
 
mini-jack
 

4...

3-2
 
IBM
 
M400
 
PROJECTOR:
 
User ’s
 
Guide 

Chapter
 
4.
 
Using
 
the
 
projector
 
features
 
This
 
chapter
 
provides
 
information
 
on
 
using
 
the
 
remote
 
control,
 
audio,
 
keypad
 
buttons,
 
and
 
other
 
projector
 
features.
 
Using
 
the
 
remote
 
control
 
The
 
remote
 
uses
 
two
 
provided
 
AAA
 
batteries.
 
They
 
are
 
easily
 
installed
 
by
 
sliding
 
the
 
cover
 
off
 
the
 
back
 
of
 
the
 
remote,
 
aligning
 
the
 
+
 
and
 
-
 
ends
 
of
 
the
 
batteries,
 
sliding
 
them
 
into
 
place,
 
and
 
then...

Inserting
 
the
 
remote
 
control
 
batteries
 
When
 
using
 
the
 
remote
 
control
 
for
 
the
 
first
 
time,
 
install
 
the
 
batteries
 
that
 
were
 
supplied.
 
Follow
 
the
 
steps
 
below
 
for
 
inserting
 
new
 
batteries
 
into
 
your
 
remote
 
control.
 
1.
   
 
Remove
 
the
 
battery
 
compartment
 
cover
 
by
 
sliding
 
the
 
cover
 
in
 
the
 
direction
 
of
 
the
 
arrow,
 
as
 
shown.
  
 
 
 
2.
 
 
 
Insert
 
the
 
supplied
 
batteries
 
taking
 
note
 
of
 
the
 
polarity...