IBM Projector E500 User Manual

							Chapter 2. Setting up the projector 
This chapter provides information on starting and shutting down the projector, 
adjusting the projector height and level, adjusting the zoom, focus, and keystone, 
and adjusting the volume. 
 
 
Attention 
Before moving the projector, be sure to power down the projector normally 
and disconnect the projector from the main power source.
Starting and shutting down the projector 
Please follow the steps below to start the projector and to shut down the projector. 
1.   
 Connect the power cord to the projector as shown below. Connect the other 
end to a wall outlet. The Power LED and Lamp-ready LED turn on. 
 
 
   
2. 
 
 Remove the lens cover. 
3. 
 
 Connect to an input device. 
4. 
 
 Turn on the connected devices. 
5. 
 
 Ensure that the Lamp-ready LED is on a steady amber, then press the Power 
button to turn on the projector. 
The projector splash screen displays and connected devices are detected. If the 
connected device is a ThinkPad, press Fn + F7 on the computer keyboard to 
switch the display output to the projector. Check the user ’s manual of non- 
Lenovo PCs to determine the appropriate Fn hot keys to change display output. 
 
 
Attention 
Do not look directly into the projection lens when the lamp is turned on. 
The bright light may harm your eyes
 
© Copyright Lenovo 2005. © Portions Copyright IBM Corp. 2004. 2-1  
						

							6.   
 If more than one input devices is connected, press the Source button repeatedly 
to switch among devices. 
7. 
 
 To turn off the projector, press the Power button. The projector prepares for 
shutdown, and a ″Wait a moment please...″ message appears. 
8. 
 
 When the ″Power off?/Press Power again″ message appears, press the Power 
button. The projector turns off. 
Note: 
 The projector will enter a cool down mode, and the fans will continue to 
run for approximately 90 seconds. Do not remove power to the projector 
until the fans have stopped. 
9. 
 
 Turn off the room light and leave.
Note:
   Leave the power cable plugged in for at least 2-5 minutes until the projector 
returns to room temperature before placing the projector inside the soft case. 
Placing the projector into the case too soon after switching off the power 
could cause the projector to over heat. 
 
 
Attention 
Before moving the projector, be sure to power down the projector normally 
and disconnect the projector from the main power source.
Adjusting the projector height 
To adjust the projector height, complete the following procedure: 
1.   
 To raise the height of the projector, lift the projector as shown in 
1 and press 
the elevator-foot buttons as shown in 
2. The elevator foot drops down as 
shown in 
3. 
2. 
 
 To lower the height of the projector, press the elevator-foot button as shown in 

2 and push down on the top of the projector. 
3. 
 
 To make adjustments to the level, rotate the leveling foot as shown in 
4.
 
2-2 E500 Projector: User ’s Guide 
						

							Positioning the projector 
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Following are some general guidelines: 
v   
 Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 1.5 m (4.9 ft) from the projection screen. 
v 
 
 Position the projector within 2.7 m (9 ft) of your power source and within 1.8 m 
(6 ft) of your video device (unless you purchase extension cables). To ensure 
adequate cable access, do not place the projector within .15 m (6 in.) of a wall or 
other object. 
v 
 
 Position the projector the desired distance from the screen. The distance from the 
lens of the projector to the screen, the zoom setting, and the video format 
determine the size of the projected image.
 
 
Chapter 2. Setting up the projector 2-3 
						

							Table 2-1. 
Diagonal screen size  
 
(m/in.) 
Image Width  
 
(m/ft) 
Image height  
 
(m/ft) 
Distance from center 
of lens to bottom of 
image  
 
(m/ft) 

1 1.10/43.3 .88/2.88 .66/2.16 1.5/4.92 

2 1.47/57.8 1.17/3.83 .88/2.88 2/6.56 

3 1.76/69.3 1.4/4.59 1.1/3.6 2.4/7.87 

4 2.06/81.1 1.64/5.38 1.23/4.03 2.8/9.18 

5 2.35/92.5 1.87/6.13 1.41/4.62 3.2/10.5 

6 2.65/104.3 2.11/6.92 1.58/5.18 3.6/11.81 

7 2.94/115.7 2.34/7.67 1.76/5.77 4/13.12 

8 3.23/127.2 2.57/8.43 1.94/6.36 4.4/14.4
   
Adjusting the zoom, focus and keystone 
To adjust the image, follow these steps. 
1. 
 
 Use the Image-focus control on the projector to sharpen the projected image as 
shown in 
1. 
2. 
 
 Use the Image-zoom control on the projector to resize the projected image and 
screen size as shown in 
2. 
 
 
Figure 2-1. 
 
2-4 E500 Projector: User ’s Guide 
						

							3.   
 Use the Keystone buttons (shown below) to correct image-trapezoid effect. 
 
 
 
The keystone control appears on the display.
Adjusting the volume 
To adjust the volume, follow the steps below. 
1.   
 Press the Volume +/- buttons on the projector or the remote control. The 
volume control appears on the OSD. 
2. 
 
 Use the Volume +/- buttons to adjust the level. The volume buttons on the 
projector and remote control are shown below. 
 
 
   
3. 
 
 Press the Mute button (on the remote control only) to turn off the volume. See 

3 in the figure above. 
4. 
 
 Press the Volume +/- buttons on the projector or the remote control to turn off 
the mute.
 
Chapter 2. Setting up the projector 2-5 
						

							2-6 E500 Projector: User ’s Guide 
						

							Chapter 3. Connecting devices to the projector 
This chapter provides information on connecting devices to the E500 Projector. 
Connecting devices 
Computers and video devices can be connected to the projector at the same time. 
Check the user ’s manual of the connecting device to confirm that it has the 
appropriate output connector. 
   
 
 

1 Audio-in 

2 RS-232 

3 Video cable 

4 Composite video 

5 S-video 

6 USB
   
Connecting to a USB device 
To use the mouse function on the projector remote control, connect the projector to 
the computer with a USB cable as shown below. 
 
 
 
 
© Copyright Lenovo 2005. © Portions Copyright IBM Corp. 2004. 3-1  
						

							Note:   USB mouse function is only supported with Windows 2000 and Windows 
XP.
 
3-2 E500 Projector: User ’s Guide 
						

							Chapter 4. Using the projector features 
This chapter provides information on using the remote control, audio, keypad 
buttons, and other projector features. 
Using the remote control 
The remote uses two provided AAA batteries. They are easily installed by sliding 
the cover off the back of the remote, aligning the + and - ends of the batteries, 
sliding them into place, and then replacing the cover. 
   
 
CAUTION: 
To reduce the risk of injury to the eyes, do not look directly into the remote 
control laser light and do not point the laser light into anyone’s eyes. The 
remote control is equipped with a Class II laser that emits radiation. 
The figure below provides an illustration of the remote. 
 

1 Laser  
 
2 IR transmitter 

3 Status LED 

4 Auto 

5 Blank 

6 Enter 

7 Up cursor 

8 Right cursor 

9 Cursor pad 

10 Keystone top 

11 Keystone bottom 

12 Mute 

13 Right mouse 

14 Left mouse 

15 Volume down 

16 Down cursor 

17 Volume up 

18 Left cursor 

19 Menu 

20 Freeze 

21 Source 

22 Power
 
 
© Copyright Lenovo 2005. © Portions Copyright IBM Corp. 2004. 4-1  
						

							Inserting the remote control batteries 
When using the remote control for the first time, install the batteries that were 
supplied. Follow the steps below for inserting new batteries into your remote 
control. 
1.   
 Remove the battery compartment cover by sliding the cover in the direction of 
the arrow, as shown. 
 
 
   
2. 
 
 Insert the supplied batteries taking note of the polarity (+/-), as shown. 
 
 
   
3. 
 
 Replace the cover, as shown. 
 
 
 
Note:   
v 
 
 Only use AAA alkaline batteries. 
v 
 
 Dispose of used batteries according to local government ordinance 
regulations. 
v 
 
 Remove the batteries when not using the remote for prolonged periods.
 
4-2 E500 Projector: User ’s Guide