Hyundai H Lcd2216 Instruction Manual

ТЕЛЕВИЗОР
ЦВЕТНОГО ИЗОБРАЖЕНИЯ
ЖИДКОКРИСТАЛЛИЧЕСКИЙ (LCD)
LCD TV
Руководство по эксплуатации 
Instruction manual
H-LCD2216
 

Table of contents 
Before you start 
Utilization of the product 
Important safeguards
Installation and connection
ConnectionOutdoor antenna connection
Other connections
Operation
Control elements  Front panel
 Back panel
Remote controller Changing the battery
General operations  Signal sources
 Teletext operations
 PC screen
OSD operation Picture setting
Sound setting
Setting
 Function setting
 Channel setting
 PC setup
 Picture setup
General information
Troubleshooting Causes of interference...

23
Table of contentsBefore you start
If you want to dispose this product, do not mix it with general household waste. There is 
a separate collection system for used electronic products in accordance with legislation 
that requires proper treatment, recovery and recycling. Please contact your local authorities for the correct method of disposal. By doing so, 
you will ensure that your disposed product undergoes the necessar y treatment, recovery 
and recycling and thus prevent potential negative effects...

4
Before you start
• Do not place any vase, potted plant, cup, 
medicine and any container with water on this 
product. If the liquid is spilt, it may cause the 
fire, electric shock or breakdown. •  Do not install it at the place on the strong 
magnetic field or current field. It may cause 
break down. This equipment may be observed 
deterioration of the picture by electromagnetic 
radiation in electromagnetic environment. •  Fasten the wheel of the product or shelf 
with wheels when installing this...

5
Installation and connection
Outdoor Antenna ConnectionUse 75Ω coaxial cable plug or 300-75Ω 
impedance converter to plug in antenna input 
terminal on the rear of the cabinet.
Other connections•  Connect the audio sources (Including 
DVD, VCDR, CAMCORDER and PC) to the 
proper AUDIO input jacks ‘L’ and ‘R’. •  Connect the video source to the VIDEO 
jack by RCA cable. •  If the video source has a SCART output 
jack, you can connect the signal to the monitor 
by the SCART cable. •  Connect the video...

6
Operation
Control elements    
Front panel
Back panel
1. POWER button
2. SOURCE button
3. MENU button
4. CH- button
5. CH+ button
6. VOL- button 7. VOL+ button
8. HDMI input
9. VGA input
10. SCART connector
11. S-Video input
12. Composite video input13. Audio (right) input
14. Audio (left) input
15. PC audio input
16. Headphone output
17. TVRF antenna input
Power indicator
8
9
10
11
12
13
14
15
16
171
2
3
4
5
6
7
Downloaded From TV-Manual.com Manual” 

7
Operation
Remote controller (RC)
1.  POWER button
2.  SLEEP button
3.  Number buttons
4.  P.MODE button
5.  SOURCE button
6.  OK button
7.  Cursor buttons (
///)
8.  VOL+/VOL- buttons
9.  INFO button 
10. EXIT button
11. CANCEL button
12. TTX/MIX button
13. REVEAL button
14. INDEX button 15. GREEN button
16. RED button
17. MUTE button
18. 
 button
19. S.MODE button
20. MENU button
21. PROGRAM+/PROGRAM- buttons
22. ASPECT button
23. AUDIO I/II button
24. SIZE button
25. HOLD/FAV button
26. SUBPAGE...

89
OperationOperation
General operations
•  Press POWER button on the unit or on 
the RC to switch on the power, the indication 
light will be in blue color. Press POWER button 
again to switch off the power, and the light will 
be in red color. •  Press VOL- button repeatedly to decrease 
the volume; press VOL+ button repeatedly to 
increase the volume. •  Press SLEEP button repeatedly to set the 
sleep time (from 0 to 120 min). To check the 
remaining sleep time, press SLEEP button; 
the  time...

89
OperationOperation
PC screenSelect the VGA input (TV into PC) mode. 
The unit has a VGA jack for a normal 
computer. Connect the monitor with a PC 
by this jack and the unit can be used as the 
monitor for the PC.
OSD operation
Press MENU button on the RC to enter the 
OSD menu. Use use 
/ buttons to select a 
setting page displayed on the screen. Press 
/ buttons to go to the needed 
item, then use 
/ buttons to select available 
setting or to adjust the selected item. Press OK 
button to confirm...

10
Operation
Function setting
FUNCTION
MOVE SELECT EXIT
SLEEP TIMER
ASPECT
TT LANGUAGE
BLUE SCREEN
SYSTEM LOCK
FTI
•  Sleep Timer: select sleep time to let unit 
go into standby state automatically. •  Aspect: select an LCD screen display 
aspect size which corresponds to your viewing 
requirements. This available aspect size may 
be different for different input source. •  TT language: select needed teletext 
language. •  Blue Screen: select On/Off. Selecting On 
means the screen background colour could...