Husqvarna Etech Ii 326l Manual
Here you can view all the pages of manual Husqvarna Etech Ii 326l Manual. The Husqvarna manuals for Trimmer are available online for free. You can easily download all the documents as PDF.
Page 1
EE E E nn n n gg g g ll l l ii i i ss s s hh h h 326C 326L 326LS 326L X-series 326LD X-series Oper ator’s manual (EPA) Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine.
Page 2
KEY T O SYMBOLS 2 – English 1151471-95 Re v . 1 2009-01-16 Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •...
Page 3
CONTENTS English – 3 1151471-95 Re v . 1 2009-01-16 Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet...
Page 4
INTR ODUCTION 4 – English 1151471-95 Re v . 1 2009-01-16 Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over 300...
Page 5
WHA T IS WHA T? English – 5 1151471-95 Re v . 1 2009-01-16 What is what? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lockout 10 Cylinder cover 11 Starter handle 12 Fuel tank 13 Choke control 14 Air purge 15 Air filter cover 16 Handle adjustment 17 Shaft coupling 18 Operator’s manual 19 Drive disc 20 Socket spanner 21 Locking pin 22 Allen key 23 Spark...
Page 6
GENERAL SAFETY PRECA UTIONS 6 – English 1151471-95 Re v . 1 2009-01-16 Impor tantPersonal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in...
Page 7
GENERAL SAFETY PRECAUTIONS English – 71151471-95 Rev. 1 2009-01-16 CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby. Machine′s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out...
Page 8
GENERAL SAFETY PRECAUTIONS 8 – English1151471-95 Rev. 1 2009-01-16 Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. Vibration...
Page 9
GENERAL SAFETY PRECAUTIONS English – 91151471-95 Rev. 1 2009-01-16 If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked screen will cause the engine to overheat and may lead to serious damage. Locking nut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the...
Page 10
ASSEMBLY 10 – English1151471-95 Rev. 1 2009-01-16 Fitting the loop handle (326C) •Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (326L, 326LS, 326Lx, 326LDx) •Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. •...