Home > Husqvarna > Chainsaw > Husqvarna 450 X Torq Owners Manual

Husqvarna 450 X Torq Owners Manual

Here you can view all the pages of manual Husqvarna 450 X Torq Owners Manual. The Husqvarna manuals for Chainsaw are available online for free. You can easily download all the documents as PDF.

Page 21

STARTING AND STOPPING
English – 21115 13 81-26 Rev.3 2009-01-14
Starting and stopping
Starting
The chain brake must be engaged when the chain saw is 
started. Activate the brake by moving the front hand guard 
forwards.
Cold engine
Start position (1): Set the start/stop switch in the choke 
position by pulling the red control outward - upward.
Decompression valve (2): Press the valve to reduce the 
pressure in the cylinder and make starting easier. Once 
the machine has started the valve will...

Page 22

STARTING AND STOPPING
22 – English115 13 81-26 Rev.3 2009-01-14
CAUTION! Do not pull the starter cord all the way out and 
do not let go of the starter handle when the cord is fully 
extended. This can damage the machine.
Note! Reactivate the chain brake by pushing the front 
hand guard back towards the front handle. The chain 
saw is now ready for use.
• Never start a chain saw unless the bar, chain and all 
covers are fitted correctly. See instructions under the 
heading Assembly. Without a bar and...

Page 23

WORKING TECHNIQUES
English – 23115 13 81-26 Rev.3 2009-01-14
Before use:
1Check that the chain brake works correctly and is not 
damaged.
2 Check that the rear right hand guard is not damaged.
3 Check that the throttle lockout works correctly and is 
not damaged.
4 Check that the stop switch works correctly and is not 
damaged.
5 Check that all handles are free from oil.
6 Check that the anti vibration system works and is not 
damaged.
7 Check that the muffler is securely attached and not 
damaged.
8...

Page 24

WORKING TECHNIQUES
24 – English115 13 81-26 Rev.3 2009-01-14
6Before moving your chain saw switch off the engine 
and lock the chain using the chain brake. Carry the 
chain saw with the bar and chain pointing backwards. 
Fit a guard to the bar before transporting the chain 
saw or carrying it for any distance.
7 When you put the chain saw on the ground, lock the 
saw chain using the chain brake and ensure you have 
a constant view of the machine. Switch the engine off 
before leaving your chain saw for...

Page 25

WORKING TECHNIQUES
English – 25115 13 81-26 Rev.3 2009-01-14
the saw chain is jamming, the saw may be pushed 
back at you.
8 Unless the user resists this pushing force there is a 
risk that the chain saw will move so far backwards that 
only the kickback zone of the bar is in contact with the 
tree, which will lead to a kickback.
Cutting with the bottom edge of the bar, i.e. from the 
top of the object downwards, is known as cutting on 
the pull stroke. In this case the chain saw pulls itself 
towards...

Page 26

WORKING TECHNIQUES
26 – English115 13 81-26 Rev.3 2009-01-14
Limbing
When limbing thick branches you should use the same 
approach as for cutting.
Cut difficult branches piece by piece.
Cutting
If you have a pile of logs, each log you attempt to cut 
should be removed from the pile, placed on a saw horse 
or runners and cut individually.
Remove the cut pieces from the cutting area. By leaving 
them in the cutting area, you increase the risk for 
inadvertently getting a kickback, as well as increasing the...

Page 27

WORKING TECHNIQUES
English – 27115 13 81-26 Rev.3 2009-01-14
Felling direction
The aim is to fell the tree in a position where you can limb 
and cross-cut the log as easily as possible. You want it to 
fall in a location where you can stand and move about 
safely.
Once you have decided which way you want the tree to fall 
you must judge which way the tree would fall naturally.
Several factors affect this:
• Lean of the tree
• Bend
• Wind direction
• Arrangement of branches
• Weight of snow
• Obstacles...

Page 28

WORKING TECHNIQUES
28 – English115 13 81-26 Rev.3 2009-01-14
Next make the bottom cut so that it finishes exactly at the 
end of the top cut.
The directional cuts should run 1/4 of the diameter 
through the trunk and the angle between the top cut and 
bottom cut should be 45
°.
The line where the two cuts meet is called the directional 
cut line. This line should be perfectly horizontal and at 
right angles (90
°) to the chosen felling direction.
Felling cut
The felling cut is made from the opposite side...

Page 29

WORKING TECHNIQUES
English – 29115 13 81-26 Rev.3 2009-01-14
Freeing a tree that has fallen badly 
Freeing a ”trapped tree”
It is very dangerous to remove a trapped tree and there is 
high accident risk.
Never try to fell the tree that is trapped.
Never work in the risk zone of the hanging trapped tree.
The safest method is to use a winch.
• Tractor-mounted
• Portable
Cutting trees and branches that are in tension
Preparations: Work out which side is in tension and where 
the point of maximum tension is...

Page 30

WORKING TECHNIQUES
30 – English115 13 81-26 Rev.3 2009-01-14
was being used when the kickback zone of the bar 
touched the object.
Kickback only occurs if the kickback zone of the bar 
touches an object.
Limbing
Make sure that you can stand and move about safely. 
Work on the left side of the trunk. Work as close as 
possible to the chain saw for maximum control. If possible, 
let the weight of the chain saw rest on the trunk.
Keep the trunk between you and the chain saw as you 
move along the trunk....
Start reading Husqvarna 450 X Torq Owners Manual

Related Manuals for Husqvarna 450 X Torq Owners Manual

All Husqvarna manuals