Husqvarna 325l X Manual

							English – 21
MAINTENANCE
Weekly
maintenance
1. Check the starter, the
starter cord and the return
spring.
2. Make sure that the
vibration damping
elements are not damaged.
3. Clean the outside of the
spark plug. Remove and
check the electrode gap.
Adjust the gap to 0.5 mm
or change the spark plug.
4. Clean the cooling fins on
the flywheel.
5. Clean or replace the
muffler’s spark arrest
screen (not on mufflers
with a catalytic converter).
6. Clean the carburettor area.
7. Clean the cooling fins on
the cylinder and check that
the air intake in the starter
unit is not blocked.
8. Check that the angle gear
is 3/4 filled with grease.
Fill if necessary using
special grease.
1
3
4
5
6
8
7Monthly
maintenance
1. Clean the fuel tank.
2. Clean the carburettor and
the area surrounding it.
3. Clean the fan and the area
around it.
4. Check the fuel filter and the
fuel pipe, replace if
necessary.
5. Check all cables and
connections.
6. Check the clutch, clutch
springs and the clutch drum
with regard to wear.
Replace if necessary.
7. Change the spark plug.
8. Check and clean the
muffler’s spark arrest screen
if necessary (only mufflers
with a catalytic converter).
2
4
7
6
2
3
5
1
8 
						

							22 – English
TECHNICAL DATA
325L-X/L-XT
1,50/24,5
1,34/34
1,06/27
2 700
11 000-11 700
8 014
0,9 kW/ 9 000 rpm
Ye s
Ye s
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9.0/4,1    L-XT: 9,7/4,4
92/98
109/109
1,5/1,4 L-XT: 1,5/1,4
2,0/1,8 L-XT: 2,4/2,2
2,5/4,8 L-XT: 2,5/4,8
4,9/8,0 L-XT: 5,8/7,6
322L
1,33/21,7
1,26/32
1,06/27
2 700
11 000 - 11 700
8 014
0,7 kW/ 9 000 rpm
Ye s
Ye s
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
8,4/3,8
92/98
109/109
1,5/1,4
2,0/1,8
2,5/4,8
4,9/8,0
Technical data
Engine
Cylinder capacity, cu. in/cm3
Cylinder bore, inch/mm
Stroke length, inch/mm
Idling speed, rpm
Recommended max. speed, rpm
Speed of output axle, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, US pint/litres
Weight
Weight without fuel, cutting tool and
guard, Lbs/kg
Noise levels
Equivalent noise pressure level at the
user’s ear, measured according to EN
31806 and ISO 7917, dB(A), min/max:
Equivalent noise power level at the user’s
ear, measured according to EN 31806
and ISO 10884, dB(A), min/max:
Vibration levels
Vibration levels on the handles,
measured according to EN 31806 and
ISO 7916, m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
322C
1,33/21,7
1,26/32
1,06/27
2 700
11 000 - 11 700
11 700
0,7 kW/ 9 000 rpm
Ye s
-
Walbro MB 18
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
8,8/4,0
91/94
103/105
1,8/1,8
3,2/2,2
4,4/3,3
5,5/4,6
NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values.
Approved accessories
Thread blade shaft M10 (L, L-X, L-XT)
Thread blade shaft 3/8 (R) (322C)
Plastic knifes
Trimmer headCutting attachment guard Art No.
503 93 42-02
530 05 37-99 / 537 07 67-01
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
537 07 67-01 Type
Tricut ∅ 300 mm (322L, 325L-X/L-XT)
Trimmy Hit VI (R) (322C)
Trimmy H II 1 (322L, 325L-X/L-XT)
Trimmy Fix (322L, 325L-X/L-XT)
Trimmy Hit (322L, 325L-X/L-XT)
Trimmy Hit Pro (322L, 325L-X/L-XT)
Superauto II 1 (322L, 325L-X/L-XT)
Trimmy Hit Junior(322C, 325CX) 
						

							English – 23
Technical data
Engine
Cylinder capacity, cu. in/cm3
Cylinder bore, inch/mm
Stroke length, inch/mm
Idling speed, rpm
Recommended max. speed, rpm
Speed of output axle, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, US pint/litres
Weight
Weight without fuel, cutting tool and
guard, Lbs/kg
Noise levels
Equivalent noise pressure level at the
user’s ear, measured according to EN
31806 and ISO 7917, dB(A), min/max:
Equivalent noise power level at the user’s
ear, measured according to EN 31806
and ISO 10884, dB(A), min/max:
Vibration levels
Vibration levels on the handles,
measured according to EN 31806 and
ISO 7916, m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
325CX
1,50/24,5
1,34/34
1,06/27
2 700
11 000-11 700
11 700
0,9 kW/ 9 000 rpm
Ye s
–
Walbro MB 18
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,3/4,2
92/97
107/108
2,5/2,1
3,2/,2
4,4/4,2
6,2/8,4
Approved accessories
Thread blade shaft 3/8 (R)
Plastic knifes
Trimmer headCutting attachment guard Art No.
537 07 67-01
537 07 67-01
537 07 67-01
537 07 67-01 Type
Tricut ∅ 230 mm (R)
Trimmy Hit VI (R)
Trimmy Fix (R)
Trimmy Hit Junior (R) NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values. 
						

							24 – English
EU declaration of conformity (Only applies to Europe)
(Directive 98/37/EC, Annex II, A)
We, Husqvarna AB, S-561 82 Huskvarna, Sweden, tel: +46 36-146500, declare under sole responsibility that the
clearings saws Husqvarna 322C, 322L, 325C-X, 325L-X/L-XT and 325CX from 1999’s serial numbers and onwards (the
year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following
standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:
- of June 22 1998 “relating to machinery” 98/37/EC and applicable supplements.
- of May 3 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
The following standards have been applied: EN292-2, CISPR 12:1997, EN ISO 11806.
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3 S-754 50 Uppsala, Sweden, has carried out voluntary type
approval for Husqvarna AB. The certificates are numbered: SEC/98/629 – 322C, SEC/98/630 – 322L,
SEC/98/631–325L-X, SEC/99/695 – 325L-XT, SEC/00/741– 325CX.
Huskvarna 14 April 2000
Bo Andréasson, Development manager. 
						

							English – 25
1 Super Auto II
Super Auto II 12
3
4
5
6
78
9
10
4,0 m
  13
2,4 mm
.095
~2,0 m
6,5

66


15 cm15 cm 
						

							26 – English
1 Tri Cut
2
3
4
5
67
8>20mm
>20mm
!
B
A
6 Nm
X 10 
						

							English – 27
1 Trimmy H II
2
3
4
5
67
8
9
7,5 m
  25
2,0-2,4 mm
.080-.095
12
 15 cm
    6
~ 3,7 m
   12
 15 cm
    6 
						

							28 – English
1 Trimmy Hit
23
4
5
6
7
89
10
11
“Click”
“Click”
7,0 m
   23

  12 cm
      5
~ 3,5 m
     11
15 cm
    6


2,0-2,4 mm
.080-.095
~ 15 cm
      6 
						

							English – 29
1 Trimmy Hit Junior
2
5
6
7
89
10
12
“Click”
3
4
5,75 m
   19
2,0-2,4 mm
.080-.095
15 cm
     6
~ 2,8 m
    9
1.)
2.)
11
15 cm
     6
15 cm
     6 
						

							30 – English
1 Trimmy Hit Pro
2
5
6
7
89
10
12
“Click”
3
4
7,5 m
   25
2,0-2,4 mm
.080-.095
15 cm
     6
~ 3,7 m
    12
1.)
2.)
11
15 cm
     6
15 cm
     6