Home > Husqvarna > Brush Cutter > Husqvarna 323 C Service Manual

Husqvarna 323 C Service Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Husqvarna 323 C Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 35 Husqvarna manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							English – 21
    MAINTENANCE
    the excess before fitting the filter to the machine. Never use 
    common engine oil. This would drain through the filter quite 
    quickly and collect in the bottom.
    Bevel gear
    (323L, 323LD, 325Lx, 325LDx)
    The bevel gear is filled with the right quantity of grease at the 
    factory. However, before using the machine you should check 
    that the bevel gear is filled three-quarters full with grease. Use 
    HUSQVARNA special grease.
    The grease in the bevel gear does not normally need to be 
    changed except if repairs are carried out.
    Maintenance schedule
    Below you will find some general maintenance instructions. If 
    you need further information please contact your service 
    workshop.
    Daily maintenance
    1 Clean the outside of the machine.
    2 Check that the components of the throttle control work 
    safely. (Throttle lock and throttle control.)
    3 Check that the stop switch works correctly.
    4 Check that the handle and handlebar are undamaged and 
    secured correctly.
    5 Check that the cutting attachment does not rotate at idle.
    6 Clean the air filter. Replace if necessary.
    7 Check that the guard is undamaged and not cracked. 
    Replace the guard if it has been exposed to impact or is 
    cracked.
    8 Check that the trimmer head is undamaged and not 
    cracked. Replace the trimmer head if necessary.
    9 Check that the locking nut is tight.
    10 Check that nuts and screws are tight.
    11 Check that the screws that hold the bevel gear are tight.
    12 Check that there are no fuel leaks from the engine, tank or 
    fuel lines.
    Weekly maintenance
    1 Check the starter and starter cord.
    2 Check that the vibration damping elements are not 
    damaged.
    3 Clean the outside of the spark plug. Remove it and check 
    the electrode gap. Adjust the gap to 0.5 mm or replace the 
    spark plug. Check that the spark plug is fitted with a 
    suppressor.
    4 Clean the cooling fins on the flywheel.
    5 Clean or replace the spark arrestor mesh on the muffler 
    (only applies to mufflers without a catalytic converter).
    6 Clean the carburettor compartment.
    7 Clean the cooling fins on the cylinder and check that the 
    air intake near the starter is not blocked.
    8 Check that the bevel gear is filled three-quarters full with 
    lubricant. Fill if necessary using special grease.
    Monthly maintenance
    1 Clean the fuel tank.
    2 Clean the outside of the carburettor and the space around 
    it.
    3 Clean the fan and the area around it.
    4 Check the fuel filter and the fuel hose. Replace if 
    necessary.
    5 Check all cables and connections.
    6 Replace the spark plug. Check that the spark plug is fitted 
    with a suppressor.
    7 Check and clean the spark arrestor mesh on the muffler 
    (only applies to mufflers fitted with a catalytic converter).
    12
    3
    5678
    9104
    1112
    40,5 mm
    5678
    321  
    						
    							22 – English
    TECHNICAL DATA
    Technical data
    Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.
    Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various 
    working conditions with the following time distribution: 1/2 idling and 1/2 max speed.
    NOTE!   The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting 
    attachments for the machine. The table indicates the lowest  and highest values.
    323C323L323LD
    Engine
    Cylinder displacement, cm324,524,524,5
    Cylinder bore, mm34,034,034,0
    Stroke, mm272727
    Idle speed, rpm270027002700
    Recommended max. fast idle speed, rpm11000-1170011000-1170010000-10500
    Speed of output shaft, rpm1170080148014
    Max. engine output, acc. to ISO 8893, kW/ rpm0,9/90000,9/90000,9/9000
    Catalytic converter mufflerNoNoNo
    Speed-regulated ignition systemNoNoYe s
    Ignition system
    Manufacturer/type of ignition systemWalbroMB/SEM 
    AM49WalbroMB/SEM 
    AM49WalbroMB/SEM 
    AM49
    Spark plugChampion RCJ 7YChampion RCJ 7YChampion RCJ 7Y
    Electrode gap, mm0,50,50,5
    Fuel and lubrication system
    Manufacturer/type of carburettorZama C1QZama C1QZama C1Q
    Fuel tank capacity, litre0,50,50,5
    Weight
    Weight without fuel, cutting attachment and guard, kg4,24,14,3
    Noise emissions
    (see note 1)
    Sound power level, measured dB(A)108106106
    Sound power level, guaranteed LWA dB(A)109106106
    Noise levels
    (see note 2)
    Equivalent noise pressure level at the operator’s ear, 
    measured according to EN/ISO 11806 and ISO 7917, 
    dB(A), min./max.:91/9891/9790/98
    Vibration levels
    Vibration levels at handles, measured according to EN/
    ISO 11806 and ISO 7916, m/s2
    At idle, left/right handles, min.:2,7/1,51,8/1,41,8/1,4
    At idle, left/right handles, max.:3,5/1,72,8/1,83,5/2,1
    At max. speed, left/right handles, min.:4,0/3,52,7/5,22,7/5,2
    At max. speed, left/right handles, max.:6,0/9,07,2/9,87,2/9,8 
    						
    							English – 23
    TECHNICAL DATA
    Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.
    Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various 
    working conditions with the following time distribution: 1/2 idling and 1/2 max speed.
    NOTE!   The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting 
    attachments for the machine. The table indicates the lowest  and highest values.
    Technical data325Cx325Lx325LDx
    Engine
    Cylinder displacement, cm324,524,524,5
    Cylinder bore, mm34,034,034,0
    Stroke, mm272727
    Idle speed, rpm270027002700
    Recommended max. fast idle speed, rpm11000-1170011000-1170010000-10500
    Speed of output shaft, rpm1170080148014
    Max. engine output, acc. to ISO 8893, kW/ rpm0,9/90000,9/90000,9/9000
    Catalytic converter mufflerYe sYe sYe s
    Speed-regulated ignition systemNoNoYe s
    Ignition system
    Manufacturer/type of ignition systemWalbroMB/SEM 
    AM49WalbroMB/SEM 
    AM49WalbroMB/SEM 
    AM49
    Spark plugChampion RCJ 7YChampion RCJ 7YChampion RCJ 7Y
    Electrode gap, mm0,50,50,5
    Fuel and lubrication system
    Manufacturer/type of carburettorZama C1QZama C1QZama C1Q
    Fuel tank capacity, litre0,50,50,5
    Weight
    Weight without fuel, cutting attachment and guard, kg4,24,14,4
    Noise emissions
    (see note 1)
    Sound power level, measured dB(A)107108108
    Sound power level, guaranteed LWA dB(A)109110110
    Noise levels
    (see note 2)
    Equivalent noise pressure level at the operator’s ear, 
    measured according to EN/ISO 11806 and ISO 7917, 
    dB(A), min./max.:92/9792/9890/98
    Vibration levels
    Vibration levels at handles, measured according to EN/
    ISO 11806 and ISO 7916, m/s2
    At idle, left/right handles, min.:2,5/2,11,5/1,41,5/1,4
    At idle, left/right handles, max.:3,2/2,22,0/1,82,4/2,2
    At max. speed, left/right handles, min.:4,4/4,22,5/4,82,5/4,8
    At max. speed, left/right handles, max.:6,2/8,44,9/8,05,8/7,6 
    						
    							24 – English
    TECHNICAL DATA
    323C
    Approved accessoriesTypeCutting attachment guard, Art. no.
    Blade shaft thread 3/8 R
    Trimmer headTrimmy Fix 3/8” (R)537 02 61-01
    Trimmy Hit VII (R)537 02 61-01
    Trimmy Hit Junior (R)537 02 61-01
    325Cx
    Approved accessoriesTypeCutting attachment guard, Art. no.
    Blade shaft thread 3/8 R
    Trimmer headTrimmy Fix 3/8” (R)537 07 67-01
    Trimmy Hit VII (R)537 07 67-01
    Trimmy Hit Junior (R)537 07 67-01
    323L, 323LD, 325Lx, 325LDx
    Approved accessoriesTypeCutting attachment guard, Art. no.
    Blade shaft thread M10
    Plastic bladesTricut Ø 300 mm503 93 42-02
    Grass blade/grass cutterGrass 255-8 1 (Ø 255 8-teeth)503 93 42-02
    Trimmer headTrimmy Fix503 93 42-02 /  503 97 71-01
    Superauto II 1503 93 42-02 /  503 97 71-01
    S35503 93 42-02 /  503 97 71-01
    T35503 93 42-02 /  503 97 71-01
    AttachmentsArt No.Use with
    Clean sweep attachment with shaft SR600537 19 67-01323LD, 325LDx
    Hedge trimmer attachment with shaft HA 110537 19 66-01323LD, 325LDx
    Hedge trimmer attachment with shaft HA 850537 19 66-02323LD, 325LDx
    Edger attachment with shaft537 19 69-01323LD, 325LDx
    Saw attachment with shaft PA 1100537 18 33-16323LD, 325LDx
    Saw attachment without shaft PA537 18 33-11323L, 325Lx
    Trimmer attachment with shaft TA 850537 35 35-01323LD, 325LDx 
    						
    							English – 25
    TECHNICAL DATA
    EC-declaration of conformity (Applies to Europe only)
    We, Husqvarna AB,  SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 323C, 323L, 
    323LD, 325C, 325Cx, 325Lx and 325LDx with serial numbers dating from 2002 onwards (the year is clearly stated on the rating 
    plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:
    of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
    of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
    of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.
    For information relating to noise emissions, see the chapter Technical data.
    The following standards have been applied:
    EN292-2, CISPR 12:1997, EN ISO 11806.
    SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type examination on 
    behalf of Husqvarna AB. The certificates are numbered: SEC/01/838, 01/164/001 - 323C, SEC/01/839, 01/164/002 - 323L, SEC/
    01/839, 01/164/002 - 323LD, SEC/98/631, 01/164/001 - 325LX, SEC/99/695, 01/164/001 - 325LDX, SEC/00/741, 01/164/003 - 
    325CX
    Huskvarna January 3, 2002
    Bo Andréasson, Development manager 
    						
    							1 Super Auto II
    Super Auto II 12
    3
    4
    5
    6
    78
    9
    10
    4,0 m
      13
    2,4 mm
    .095
    ~2,0 m
    6,5
    
    6
    6
    
    15 cm15 cm 
    						
    							Clic
    1
    2
    3
    5
    67
    10
    11
    8,5 m
    28
    4
    8
    4,2 m
    14
    2,4-2,7 mm
    .095-.106
    10 cm
         4
    6 15 cm
    S35 
    						
    							1
    2
    4
    3
    2,4-2,7 mm
    .095-.106
    4,25 m
    144,25 m
    14
    B
    6 15 cm
    A
    6 15 cm
    S35
    5 
    						
    							´®z+H:h¶6]¨
    ´®z+H:h¶6]¨
    T35
    Clic
    1
    2
    3
    5
    67
    9
    8,5 m
    28
    4
    8
    4,3 m
    14
    2,4-2,7 mm
    .095-.106
    10 cm
         4
    6 15 cm 
    						
    All Husqvarna manuals Comments (0)

    Related Manuals for Husqvarna 323 C Service Manual