Home > Husqvarna > Brush Cutter > Husqvarna 323 C Service Manual

Husqvarna 323 C Service Manual

Here you can view all the pages of manual Husqvarna 323 C Service Manual. The Husqvarna manuals for Brush Cutter are available online for free. You can easily download all the documents as PDF.

Page 11

English – 11
WHAT IS WHAT?
What is what?
1 Trimmer head
2 Grease filler cap, bevel gear
3 Bevel gear
4 Cutting attachment guard
5 Shaft
6 Loop handle
7 Throttle control
8 Stop switch
9 Throttle lock
10 Cylinder cover
11 Starter handle
12 Fuel tank
13 Choke control
14 Air purge
15 Air filter cover
16 Handle adjustment
17 Locking nut
18 Support flange
19 Drive disc
20 Socket spanner
21 Operator′s manual
22 Allen key
23 Locking pin
24 Shaft coupling 

Page 12

12 – English
ASSEMBLY
Fitting the loop handle
(323C, 325Cx)
• Position the handle on the shaft. Note that the handle 
must be mounted below the arrow on the shaft.
• Fit the screw, securing plate and wing nut as shown in the 
diagram.
• Tighten the wing nut.
Fitting the loop handle
(323L, 323LD, 325Lx, 325LDx)
• Clip the loop handle onto the shaft. Note that the loop 
handle must be fitted between the arrows on the shaft.
• Slide the spacer into the slot in the loop handle.
• 323L/323LD: Fit the nut,...

Page 13

English – 13
ASSEMBLY
Fitting the trimmer head
When fitting the cutting attachment it is extremely important 
that the raised section on the drive disc/support flange 
engages correctly in the centre hole of the cutting attachment. 
If the cutting attachment is fitted incorrectly it can result in 
serious and/or fatal personal injury.
Fitting a trimmer guard and 
Superauto II 1” trimmer head
(323L, 323LD, 325Lx, 325LDx)
• Fit the correct trimmer guard (A) for use with the trimmer 
head. Hook the guard onto...

Page 14

14 – English
ASSEMBLY
Fitting the trimmer guard and 
trimmer head
(323C)
Guard
• Fit the guard as shown in the diagram. Tighten securely.
Trimmer head
• Fit the dust cup on the shaft. The nut must be completely 
covered by the dust cup.
• Hold the dust cup with a spanner to prevent the shaft from 
rotating.
• Screw the trimmer head onto the shaft.
Fitting the trimmer guard and 
trimmer head
(325Cx)
• Fit the guard as shown in the diagram. Tighten securely.
• Insert the locking pin into the hole to lock...

Page 15

English – 15
FUEL HANDLING
Fuel
CAUTION! The machine is equipped with a two-stroke engine 
and must always been run using a mixture of petrol and two-
stroke engine oil. It is important to accurately measure the 
amount of oil to be mixed to ensure that the correct mixture is 
obtained. When mixing small amounts of fuel, even small 
inaccuracies can drastically affect the ratio of the mixture.
Petrol
CAUTION! Always use a good quality petrol/oil mixture (at 
least 90 octane). If your machine is equipped...

Page 16

16 – English
STARTING AND STOPPING
Check before starting
• Check that the support flange is not cracked due to fatigue 
or due to being tightened too much. Discard the support 
flange if it is cracked.
• Ensure the locking nut has not lost its captive force. The 
nut lock should have a locking force of at least 1.5 Nm. 
The tightening torque of the locking nut should be 35-50 
Nm.
• Check that the blade guard is not damaged or cracked. 
Replace the blade guard if it is exposed to impact or is 
cracked.
•...

Page 17

English – 17
STARTING AND STOPPING
some resistance (the starter pawls grip), now quickly and 
powerfully pull the cord. Never twist the starter cord around 
your hand.
Repeat pulling the cord until the engine starts. When the 
engine starts. return choke control to run position and apply 
full throttle; the throttle will automatically disengage from the 
start setting.
CAUTION!  Do not pull the starter cord all the way out and do 
not let go of the starter handle when the cord is fully extended. 
This...

Page 18

18 – English
MAINTENANCE
Carburettor
Your Husqvarna product has been designed and 
manufactured to specifications that reduce harmful 
emissions. After the engine has used 8-10 tanks of fuel the 
engine will be run-in. To ensure that it continues to run at peak 
performance and to minimise harmful exhaust emissions 
after the running-in period, ask your dealer/service workshop 
(who will have a rev counter at their disposal) to adjust your 
carburettor.
Function
• The carburettor governs the engine’s...

Page 19

English – 19
MAINTENANCE
will run smoothly in every position. The idle speed should also 
be well below the speed at which the cutting attachment starts 
to rotate.
WARNING! If the idle speed cannot be adjusted so that the 
cutting attachment stops, contact your dealer/service 
workshop. Do not use the machine until it has been correctly 
adjusted or repaired.
High speed jet H
The high speed jet H affects the engine power, speed, 
temperature and fuel consumption. If the high speed jet H is 
set too lean...

Page 20

20 – English
MAINTENANCE
Cooling system
To keep the working temperature as low as possible the 
machine is equipped with a cooling system.
The cooling system consists of:
1 Air intake on the starter.
2 Fins on the flywheel.
3 Cooling fins on the cylinder.
4 Cylinder cover (directs cold air over the cylinder).
Clean the cooling system with a brush once a week, more 
often in demanding conditions. A dirty or blocked cooling 
system results in the machine overheating which causes 
damage to the piston and...
Start reading Husqvarna 323 C Service Manual

Related Manuals for Husqvarna 323 C Service Manual

All Husqvarna manuals