Husqvarna 322 C Manual

							English – 21
TECHNICAL DATA
Technical data
Engine
Displacement, cu. in/cm3
Cylinder bore, inch/mm
Stroke length, inch/mm
Recommended max. speed, rpm
Idling speed, rpm
Speed of output shaft, rpm
Max. engine output, acc. to ISO 8893,
kW/rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel lubrication system
Manufacturer/type of carburetor
Fuel tank capacity, US pint/litres
Weight
Weight without fuel, cutting tool and
guard, Lbs/kg
Sound levels (se note 1)
Equivalent sound pressure level at the user’s
ear, measured according to ANSI B175.3-
1997, dB(A), min/max:
Vibration levels
Vibration levels on the handles, measured
according to ANSI B175.3-1997, m/s
2
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
NOTE! Sound pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting
equipment fitted. The table indicates the highest and lowest values.
322L/323L
1,50/24,5
1,34/34
1,06/27
11 000 - 11 700
2 700
8 014
0,9/ 9 000
No
No
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,0/4,1
91/97
1,8/1,4
2,8/1,8
2,7/5,2
7,2/9,8
325LX
1,50/24,5
1,34/34
1,06/27
11 000 - 11 700
2 700
8 014
0,9/ 9 000
Ye s
No
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,0/4,1
92/98
1,5/1,4
2,0/1,8
2,5/4,8
4,9/8,0
325LXT
1,50/24,5
1,34/34
1,06/27
11 000 - 11 700
2 700
8 014
0,9/ 9 000
Ye s
No
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,7/4,4
90/98
1,5/1,4
2,4/2,2
2,5/4,8
5,8/7,6
325LDX
1,50/24,5
1,34/34
1,06/27
10 000 - 10 500
2 700
8 014
0,9/ 9 000
No
Ye s
Walbro MB 28
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,7/4,4
90/98
1,5/1,4
2,4/2,2
2,5/4,8
5,8/7,6 
						

							22 – English
325CX-series
1,50/24,5
1,34/34
1,06/27
11 000 - 11 700
2 700
11 700
0,9/ 9 000
Ye s
No
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,3/4,2
92/97
2,5/2,1
3,2/2,2
4,4/4,2
6,2/8,4
Technical data
Engine
Displacement, cu. in/cm3
Cylinder bore, inch/mm
Stroke length, inch/mm
Recommended max. speed, rpm
Idling speed, rpm
Speed of output shaft, rpm
Max. engine output, acc. to ISO 8893
kW/rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel lubrication system
Manufacturer/type of carburetor
Fuel tank capacity, US pint/litres
Weight
Weight without fuel, cutting tool and
guard, Lbs/kg
Sound levels (se note 1)
Equivalent sound pressure level at the user’s ear,
measured according to ANSI B175.3-1997,
dB(A), min/max:
Vibration levels
Vibration levels on the handles, measured
according to ANSI B175.3-1997, m/s
2
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
TECHNICAL DATA
Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
NOTE! Sound pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting
equipment fitted. The table indicates the highest and lowest values.
325C
1,50/24,5
1,34/34
1,06/27
11 000 - 11 700
2 700
11 700
0,9/ 9 000
No
No
Walbro MB 18
Champion RCJ 7Y
0,02/0,5
Zama C1Q
1,06/0,5
9,3/4,2
91/98
2,7/1,5
3,5/1,7
4,0/3,5
6,0/9,0 
						

							English – 23
TECHNICAL DATA
Approved accessories
Thread blade shaft 3/8
Trimmer headCutting attachment guard Art No.
537 02 61-01
537 02 61-01
537 02 61-01 Type
Trimmy Hit Junior (R)
Trimmy Fix 3/8 (R)
Trimmy Hit VII (R)
Approved accessories
Thread blade shaft M10
Plastic knives
Trimmer headCutting attachment guard Art No.
503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02 Type
Tricut ∅ 300 mm
Trimmy Fix
Trimmy HII 1
Trimmy Hit
Trimmy Hit Pro
Superauto II 1 322L, 323L, 325L
X, 325LXT, 325LDX
325C
Approved accessories
Thread blade shaft 3/8
Plastic knives
Trimmer headCutting attachment guard Art No.
537 07 67-01
537 07 67-01
537 07 67-01
537 07 67-01 Type
Tricut ∅ 230 mm (R)
Trimmy Hit VI (R)
Trimmy Fix (R)
Trimmy Hit VII (R) 325C
X
Art No.
537 19 67-01
537 19 66-01
537 19 69-01
537 18 33-17
537 18 33-12Use with
325LD
X325LDX325LDX325LDX322L, 323L, 325LX, 325LDX
Attachments
Clean sweep attachment with shaft
Hedge trimmer attachment with shaft
Edger with attachment shaft
Saw attachment with shaft
Saw attachment without shaft 
						

							24 – English
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND
OBLIGATIONS
The EPA (The US Environmental Protection Agency),
Environment Canada and Husqvarna Forest & Garden are
pleased to explain the emissions control system warranty
on your 2001 and later small nonroad engine. In U.S. and
Canada, new small nonroad engines must be designed,
built and equipped to meet the federal stringent anti-smog
standards. Husqvarna Forest & Garden must warrant the
emission control system on your small nonroad engine for
the periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your unit. Your
emission control system includes Parts such as the
carburetor and the ignition system.
Where a warrantable condition exists, Husqvarna Forest &
Garden will repair your small nonroad engine at no cost to
you. Expenses covered under warranty include diagnosis,
parts and labor.
MANUFACTURER’S WARRANTY
COVERAGE
The 2001 and later small nonroad engines are warranted
for two years. If any emission related part on your engine
(as listed above) is defective, the part will be repaired or
replaced by Husqvarna Forest & Garden.
OWNER’S WARRANTY
RESPONSIBILITIES
As the small nonroad engine owner, you are responsible for
the performance of the required maintenance listed in your
Operator’s Manual. Husqvarna Forest & Garden
recommends that you retain all receipts covering
maintenance on your small nonroad engine, but Husqvarna
Forest & Garden cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all
scheduled maintenance.
As the small nonroad engine owner, you should, however,
be aware that Husqvarna Forest & Garden may deny you
warranty coverage if your small nonroad engine or a part of
it has failed due to abuse, neglect, improper maintenance,
unapproved modifications or the use of parts not made or
approved by the original equipment manufacturer.
You are responsible for presenting your small nonroad
engine to a Husqvarna Forest & Garden authorized
servicing dealer as soon as a problem exists. The warranty
repairs should be completed in a reasonable amount of
time, not to exceed 30 days.
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5963.
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date small nonroad
engine is delivered.
LENGTH OF COVERAGE
Husqvarna Forest & Garden warrants to the initial owner
and each subsequent purchaser that the engine is free
from defects in materials and workmanship which cause
the failure of a warranted part for a period of two years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS
Repair or replacement of any warranted part will be
performed at no charge to the owner at an approved
Husqvarna Forest & Garden servicing dealer. If you have
any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at
1-800-487-5963.
WARRANTY PERIOD
Any warranted part which is not scheduled for replacement
as required maintenance, or which is scheduled only for
regular inspection to the effect of ”repair or replace as
necessary” shall be warranted for 2 years. Any warranted
part which is scheduled for replacement as required
maintenance shall be warranted for the period of time up to
the first scheduled replacement point for that part.
DIAGNOSIS
The owner shall not be charged for diagnostic labor which
leads to the determination that a warranted part is
defective, if the diagnostic work is performed at an
approved Husqvarna Forest & Garden servicing dealer.
CONSEQUENTIAL DAMAGES
Husqvarna Forest & Garden may be liable for damages to
other engine components caused by the failure of a
warranted part still under warranty.
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest & Garden
is not liable to cover failures of warranted parts caused by
the use of add-on or modified parts.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5963.
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement
part used in the performance of any warranty maintenance
or repairs on emission-related parts, will be provided
without charge to the owner if the part is under warranty.
EMISSION CONTROL WARRANTY
PARTS LIST
1. Carburetor and internal parts
2. Intake pipe, airfilter holder and carburetor bolts.
3. Airfilter and fuelfilter covered up to maintainance
schedule.
4. Ignition System
a) Spark Plug, covered up to maintenance schedule
b) Ignition Module
5. Muffler with catalytic converter.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual. 
						

							English – 25
1 Super Auto II
Super Auto II 12
3
4
5
6
78
9
10
4,0 m
  13
2,4 mm
.095
~2,0 m
6,5

66


15 cm15 cm 
						

							26 – English
1 Tri Cut
2
3
4
5
67
8>20mm
>20mm
!
B
A
6 Nm
X 10 
						

							English – 27
1 Trimmy H II
2
3
4
5
67
8
9
7,5 m
  25
2,0-2,4 mm
.080-.095
12
 15 cm
    6
~ 3,7 m
   12
 15 cm
    6 
						

							28 – English
1 Trimmy Hit
23
4
5
6
7
89
10
11
“Click”
“Click”
7,0 m
   23

  12 cm
      5
~ 3,5 m
     11
15 cm
    6


2,0-2,4 mm
.080-.095
~ 15 cm
      6 
						

							English – 29
1 Trimmy Hit Junior
2
5
6
7
89
10
12
“Click”
3
4
5,75 m
   19
2,0-2,4 mm
.080-.095
15 cm
     6
~ 2,8 m
    9
1.)
2.)
11
15 cm
     6
15 cm
     6 
						

							30 – English
1 Trimmy Hit Pro
2
5
6
7
89
10
12
“Click”
3
4
7,5 m
   25
2,0-2,4 mm
.080-.095
15 cm
     6
~ 3,7 m
    12
1.)
2.)
11
15 cm
     6
15 cm
     6