Hughes JVC Projector 230 Sc Service Manual
Here you can view all the pages of manual Hughes JVC Projector 230 Sc Service Manual. The Hughes JVC manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 41
Chapter 2---System Description Model 230 Service Manual2-29 HIGH VOLTAGE POWER SUPPLY INPUTS DESCRIPTION G1_SUPPLY Supply for G1 grid of CRTs. About -200 V G2_SUPPLY Supply for G2 (screen) grid of CRTs. About 1200 V RED_FOCU S GRN_FOCU S BLU_FOCU SFocus supply for CRTs. about 7 KV OUTPUTS DESCRIPTION ARC_GND CRT ground (anode supply return line) HORIZONTAL/VERTICAL DEFLECTION BOARD INPUTS DESCRIPTION /SWEEP_OK Deflection detection line. open collector, low = good deflection RASTER TIMING GENERATOR BOARD...
Page 42
Chapter 2---System Description 2-30Model 230 Service Manual RED_HEAT- GRN_HEAT- BLU_HEAT-Negative side (return line) of the heater voltage for CRTs. Ground level. RED_ CATHODE GRN_ CATHODE BLU_ CATHODEVideo output signals of the VAB. about 40 VPP with peak voltage of about 70 V. RED_GRID2 GRN_GRID2 BLU_GRID2G2 (screen) supply of CRTs. about 600 to 800 V OUTPUTS DESCRIPTION ARC_GRD Ground of CRTs ( anode supply return line). SYSTEM POWER SUPPLY INPUTS DESCRIPTION +6.2 V +6.2 V supply line (heater...
Page 43
Chapter 2---System Description Model 230 Service Manual2-31 • Fault monitors the HVPS, LVPS, Arc Lamp, and fans. • Provides interboard communication via the IIC serial bus. • Controls Zoom and Focus of the Projection Lens. • IIC Interface control • Provides Video Overlays • X and Y convergence control • Threshold and Sensitivity for shading • I/O control • Two RS-232 serial interface ports • Infrared (IR) remote control interface. Accepts input from front or rear IR detectors. • A 5-wire JTAG...
Page 44
Chapter 2---System Description 2-32Model 230 Service Manual P11 B23 B24 B28 B29 B32 B27 B26 B31 B30 Lens Zoom Lens Focus /LV_ENA /FAN_ENA /LAMP_ENA/HV_OK/LV_OK /LAMP_LIT/LAMP_OK P10 B31 B30 A32 A31 A30 A B 20-20 21-21 22-22 23-23 24-24 25-25 26-26 27-27 28-28 29-29+5.1V stby +5.1V +15V -15V GND ODD_FIELD SRC_VALID H_DRIVE_SC V_DRIVE B9 B10 B2 B1 B3 RED_OVER GRN_OVER BLU_OVERB18 B17 B16 P10 Y_RED_CONV Y_GRN_CONV Y_BLU_CONV X_RED_CONV X_GRN_CONV X_BLU_CONV B4 B5 B6 B1 B2 B3 BLU_THRES GRN_THRES RED_THRES...
Page 45
Chapter 2---System Description Model 230 Service Manual2-33 Table 2-11. System Controller Board I/O signals VIDEO PROCESSOR BOARD I/O DESCRIPTION IIC_CLK IIC clock line. Clock line for control of synchronous data transfer over the IIC bus interface. IIC_DATA IIC data line. Serial line for synchronous data transfer of the following data between Video Processor Board and SCB board. I=Input, O=Output. I BEAM CURRENT I OK DETECT O RED_CONT O GRN_CONT O BLU_CONT O BRIGHTNESS O RED_G2 O...
Page 46
Chapter 2---System Description 2-34Model 230 Service Manual BLU_SENS Sensitivity correction information for BLU. Real time data at O volt to 1 volt. GRN_SENS Similar to BLU_SENS RED_SENS Similar to BLU_SENS RASTER TIMING GENERATOR INPUTS DESCRIPTION SOURCE_ VALIDThis signal indicates a new source (or valid). A high indicates a valid stable signal and low indicates change in input signal. ODD_FIELD Square wave with 50 % duty cycle which is low during the odd field of an interlace signal. This signal is...
Page 47
Chapter 2---System Description Model 230 Service Manual2-35 X_BLU_ CONVBlu X convergence waveform. The amplitude for full scale correction is about 1 VPP. Y_RED_ CONVRed Y convergence waveform. The amplitude for full scale correction is about 1 VPP. Y_GRN_ CONVGrn Y convergence waveform. The amplitude for full scale correction is about 1 VPP. Y_BLU_ CONVBlu Y convergence waveform. The amplitude for full scale correction is about 1 VPP. CORR_ SYNCSquare wave HCT level synchronous signal for horiz axis....
Page 48
Chapter 2---System Description 2-36Model 230 Service Manual IIC_DATA IIC data line. Bidirectional serial line for synchronous data transfer between the SCB and the Horizontal/Vertical Deflection board. I=Input, O=Output. O V_RED_LIN_CONTROL O V_GRN_LIN_CONTROL O V_BLU_LIN_CONTROL O V_RED_EDGE_CONTROL O V_GRN_EDGE_CONTROL O V_BLU_EDGE_CONTROL O L/R_KEY_CONTROL O L/R_PIN_CONTROL O WIDTH_CONTROL O H_RED_CENT_CONTROL O H_GRN_CENT_CONTROL O H_BLU_CENT_CONTROL O...
Page 49
Chapter 2---System Description Model 230 Service Manual2-37 OUTPUTS DESCRIPTION FAN_ENA Signal to enable the 24V standby power LV_ENA Signal to enable the LVPS ARC LAMP POWER SUPPLY INPUTS DESCRIPTION /LAMP_OK Informs SCB that the Arc Lamp is installed, temperature is within limits, and lamp cooling blower is working /LAMP_LIT Informs the SCB that the Arc Lamp is lit or not lit OUTPUTS DESCRIPTION /LAMP_ENA Enables ALPS power PROJECTION LENS OUTPUTS DESCRIPTION LENS_FOCUSSignal to lens focus motor...
Page 50
Chapter 2---System Description 2-38Model 230 Service Manual • Horizontal and vertical phase adjustments • Interlace detection and odd field pulse generation • Horizontal frequency band selection • Horizontal line count and vertical count generation • IIC interface • Video clamp pulse generation • Source change detection • HVPS sync generation • Horizontal deflection enable circuitry The RTG I/O Diagram (Figure 2-13) and the list of inputs and outputs (Tables 2- 12 and 2-13) provide information...