HP Z 440 Owners Manual

							HP Z440 Workstations t LSI 9217-4i4e RAID controller guidelines
See HP Z440 Workstation system board components on page 5 to determine the location of system board 
connectors.
NOTE:Hard drives attached to RC J8 are designated by the 9217-4i4e BIOS to be boot devices. If the hard 
drive connected to RC J8 is a member of a RAID array, the RAID array is the boot device.System board 
connector
Drive installation scenarios123RC – Port 0SAS HDD1SAS HDD1–BSAS HDD1–BRC – Port 1SAS HDD2SAS HDD2–DSAS HDD2–DRC – Port 2SAS HDD3SAS HDD3–DSAS HDD3–DRC – Port 3SAS HDD4SAS HDD4–DSAS HDD4–DSATA 0ODD 1ODD 1ODD 1SATA 1ODD 2ODD 2ODD 2sSATA 0———sSATA 1———sSATA 2eSATA (top)SATA (top)SATA (top)sSATA 3SATA (bottom)SATA (bottom)SATA (bottom)eSATA = external SATA (2 ports per cable assembly)
If eSATA is installed, the ODD is attached to sSATA 3.
If 4 SATA HDDs are installed on sSATA and eSATA is installed, there will be no ODD.
HDD = hard drive
ODD = optical drive
NOTE:Only the most common con

						

							HP Z640 Workstations t Intel AHCI SATA controller guidelines
See HP Z640 Workstation system board components on page 11 to determine the location of system board 
connectors.
NOTE:sSATA port 0 is the default port for the boot drive (the default port can be changed manually in the 
BIOS).RAID card (RC) or system  board (SB) connectorDrive installation scenarios123RC J8 SAS HDD 1SAS HDD 1-BSATA HDD 1-BRC J7SAS HDD 2SATA HDD 2-DSAS HDD 2-DRC J6SAS HDD 3SATA HDD 3-DSAS HDD 3-DRC J5SAS HDD 4SATA HDD 4-DSAS HDD 4-DSB SATA 0———SB SATA 1———SB SATA 2ODD 1ODD 1ODD 1SB SATA 3ODD 2ODD 2ODD 2SB SATA 4eSATA (top)eSATA (top)eSATA (top)SB SATA 5eSATA (bottom)eSATA (bottom)eSATA (bottom)eSATA = external SATA (2 ports per cable assembly)
HDD = hard drive
ODD = optical drive
NOTE:Only the most common con

						

							HP Z640 Workstations t LSI 9217-4i4e RAID controller guidelines
See HP Z640 Workstation system board components on page 11to determine the location of system board 
connectors.
NOTE:Hard drives attached to RC J8 are designated by the 9217-4i4e BIOS to be boot devices. If the hard 
drive connected to RC J8 is a member of a RAID array, the RAID array is the boot device.System board connectorDrive installation scenarios123RC – Port 0SAS HDD 1SAS HDD 1-BSATA HDD 1-BRC – Port 1SAS HDD 2SATA HDD 2-DSAS HDD 2-DRC – Port 2SAS HDD 3SATA HDD 3-DSAS HDD 3-DRC – Port 3SAS HDD 4SATA HDD 4-DSAS HDD 4-DSATA 0ODD 1ODD 1ODD 1SATA 1ODD 2ODD 2ODD 2sSATA 0———sSATA 1———sSATA 02eSATA (top)eSATA (top)eSATA (top)sSATA 3eSATA (bottom)eSATA (bottom)eSATA (bottom)eSATA = external SATA (2 ports per cable assembly)
HDD = hard drive
ODD = optical drive
NOTE:If there are fewer than three hard drives in the con

						

							HP Z840 Workstation cabling guidelines
See HP Z840 Workstation system board components on page 18 to determine the location of system board 
connectors.
NOTE:Port 0 is the default port for the boot drive (the default port can be changed manually in the BIOS).
System board connector
Drive con

						

							Memory 
Supported DIMM con

						

							CAUTION:DIMMs and their sockets are keyed for proper installation. To prevent socket or DIMM damage, 
align these guides properly when installing DIMMs.
HP Z440 Workstation DIMM installation order
Install DIMMs in this order.
NOTE:If you install DIMMs of di

						

							HP Z640 Workstation DIMM installation order 
Install DIMMs in this order.
NOTE:If you install DIMMs of di

						

							HP Z840 Workstation DIMM installation order 
Install DIMMs in this order.
NOTE:If you install DIMMs of di

						

							Power supply 
Power supply specL

						

							HP Z640 power supply specL