HP Vp6220 Digital Projector Users Guide

2. Introduction 11
Controls and Functions
Projector
1. Hide button (Refer to page 23 for more information.)
Hides the display.
2. Source button (Refer to page 21 for more information.)
Switches to the next input source. Cycles through VGA, composite video, and 
S-video inputs.
3. Temperature-warning light  (Refer to page 34 for more information.)
Turns on when the internal temperature is too high.
4. Lamp-warning light (Refer to page 32 for more information.)
Turns on when lamp fails.
5. Keystone buttons...

2. Introduction 12
Remote Control
     
1. Keystone button (Refer to page 22 for more information.)
Adjust the picture to eliminate slanted sides.
2. Menu button and directional arrows (Refer to page 25 for more informa-
tion.)
Change projector settings using the on-screen menu.
3. Keystone button (Refer to page 22 for more information.)
Adjust the picture to eliminate slanted sides.
4. Page-up and page-down buttons (Refer to page 24 for more information.)
Scroll up and down through pages on a connected...

2. Introduction 13
Aiming the Remote Control
Infrared (IR) remote control sensors are located on the front and the back of the 
projector. The remote control must be held at an angle within 30 degrees of the pro-
jection screen or the projector’s IR remote control sensors to function correctly. The 
distance between the remote control and the sensors should not exceed 6 meters 
(19.5 feet). 
Notes on Remote Control Operation:
Make sure that there are no obstacles between the remote control and the IR...

3. Installation 14
3. Installation
Choosing a Location
Your projector is designed to be installed in the four installation configurations 
shown here. Your room layout or personal preference will dictate which installation 
configuration you use. 
For further information on the four configurations, please refer to page 29.
If you place the projector above or below the screen, you have to tilt it down or up to 
center the image on the screen, in these situations image distortion will occur. Use 
the...

3. Installation 15
Adjusting the Height
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster 
feet. These adjusters change the image height and projection angle. To adjust the 
projector,
1. Lift the projector up and 
press the adjuster button 
to release the adjuster. 
The adjuster will drop into 
position and be locked. It 
can lift the projector by up 
to 15 degrees. 
2. Screw the rear adjuster 
feet to fine tune the hori-
zontal angle.
Press the adjuster button again 
to...

3. Installation 16 
There is 3% ~ 5% tolerance among these numbers due to optical component variations.
Screen size chart (4:3 aspect ratio)
Distance
from
screenDiagonal measure-
mentDistance
from screenDiagonal measurement
Minimum
zoomMaximum
zoomMinimum
zoomMaximum
zoom
feet inch feet inch feet inch meter cm meter cm meter cm
4 48 2.49 29.9 3.05 36.6 1 100 0.62 62.2 0.76 76.2
6 72 3.73 44.8 4.57 54.9 1.5 150 0.93 93.3 1.14 114.3
8 96 4.98 59.7 6.10 73.2 2 200 1.24 124.5 1.52 152.4
10 120 6.22 74.7 7.62...

4. Connection 17
4. Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
In the connections shown below, only certain cables are included with the projector (see   
page 8). Other cables are available from HP or from electronics stores.
Connecting to a Laptop or Desktop Computer
 
Connecting Component-Video Devices
The projector is...

4. Connection 18
Connecting S-Video Devices
Connecting Composite-Video Devices
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the video source is turned on and operating cor-
rectly. Also check that the signal cables have been connected correctly.
S-Video cable Audio cable
Audio cable
Composite -video cable 

4. Connection 19
Connecting to Display Devices
If you want to monitor your presentation close-up on a monitor as well as on the 
screen, you can connect the VGA signal output port on the projector to an external 
monitor with a VGA cable.
VGA cable  

5. Operation 20
5. Operation
Startup
1. Switch all of the connected equipment on.
2. Plug the power cord into the projector and into a wall socket.
3. Turn on the wall socket switch (where fitted).
4. Press Power on the remote control or projector to start the unit. The Power 
button flashes during warm up, then turns on solid.
5. The projector searches the input ports for an input signal. A message on the 
screen shows the ports being searched.
You can also press source on the projector or remote...