HP Sw450 User Manual

57
The succeeding table shows the available settings.
IconItem Description
Normal  No effect is added to the image.
Sepia Image is saved with a sepia tone.
B&W Image is saved in black and white.
NegativeImage appears to be the opposite of the original image.
MosaicImage is saved with mosaic tiles.
Vivid Red Image is saved with reddish tint.
Vivid Green Image is saved with greenish tint.
Vivid Blue Image is saved with bluish tint. 

58
Trim
The Trim function allows you to trim an image to another image size. This function is only available for still images.
To trim an image:
Set the camera to Playback mode.
1. 
Use the 
2. 
 or  keys to scroll and select an image to trim.
Press the 
3.  Menu button  
 to launch the Playback menu.
Select 
4.  Trim. The Trim screen layout is displayed on the LCD 
monitor.
Move the 
5.  Zoom toggle  
 to change the photo size.
No.Description
1 Enlarged image
2 4-way indicator
3 Trimmed size
4 The...

59
Resize
Resizes a previously saved image and only resizing to a smaller size is available.
To resize an image:
Set the camera to Playback mode 
1. .
Use the 
2. 
 or  keys to scroll and select an image to resize.
Press the 
3.  Menu button  
 to launch the Playback menu.
Select 
4.  Resize. The Resize submenu is displayed on the LCD 
monitor.
Select size among: 8M, 5M, 3M, and VGA. Available size settings 
5. 
may vary depending on original image size. Unavailable settings 
appear as gray icons in...

60
DPOF
DPOF is the abbreviation for Digital Print Order Format, which allows you to embed printing information on your 
memory card. You can select the images to be printed and how many prints to make with the DPOF menu in the 
camera and insert the memory card to the card compatible printer. When the printer starts printing, it will read the 
embedded information on the memory card and print the specified images.
To set DPOF:
Press the 
1.  Menu button   to launch the Playback menu.
Select 
2.  DPOF....

61
PictBridge
The PictBridge function allows you to print images captured by your camera without connecting the camera to a PC. 
Print images with a PictBridge compatible printer directly.
To activate PictBridge:
Connect your camera to a PictBridge compatible printer using the USB cable. See illustration below.
If the printer does not support date & time imprint, the date & time imp\
rint function 
will be disabled in PictBridge.
Radial Blur
The Radial Blur is an effect creates blurs around a point,...

62
Using the Setup Menu
You can access the Setup menu whether you are in Record or Playback mode.
The Setup menu allows to configure general camera settings.
To go to Setup Menu:
Press 
1.  Menu button   to launch the Record/Playback Menu.
Use the 
2. 
 or  keys to switch the menu tab to  Setup menu.
Use the 
3. 
 or  keys to move through the menu selections.
To select an item, press the 
4.  OK button 
 or  key.
Change the submenu settings using the 4-way navigation control.
5. 
Press the 
6.  OK button...

63
Setting LCD Save
Enable the LCD Save function to automatically decrease the LCD brightness to conserve battery power. When the 
camera is idle for 20 seconds, the LCD darkens. Press any button to resume to normal brightness.The camera is idle when no buttons are pressed. LCD Save, though enabled, does not function during video 
•	
playback, slideshow, video recording and Pre-Composition scene mode shooting.
Setting Date & Time
Use the Date & Time function to set the date and time of your camera. This...

64
Setting File Numbering
This function allows you to select the method in which to assign file numbers to images.
Available settings are:
 
•	 Series.  Assigns number to files in sequence even if the folder is changed.
 
•	 Reset.  Starts from 0001 each time the folder is changed.
To understand folder and file structure of your camera, see “About Folder and File Names” on page 72.
Setting TV Out
Use the TV Out function to adjust video output signal to accommodate different regional settings. If TV out...

65
Setting Memory Kit
This utility formats the internal memory (or memory card) and erases all stored images and data.
Available settings are:
 
•	 Format.  Select to format currently used memory.
 
•	 Copy to Card. Select to copy all files stored in the internal memory to the memory card.
If the photos were saved in the internal memory when inserting memory card into 
•	
the camera. You can use  Copy to Card function in order to copy all photos from 
the internal memory into memory card.
If there is a...

66
Making Connections
Connect your camera to: computer, or a printer.
Connecting the Camera to a PC
You can transfer images, videos and audio files to your PC.Connect one end of the USB cable to an available USB port on your computer.
1. 
Connect the other end of the USB cable to the USB terminal on the camera.
2. 
Power on the camera.
3. 
The USB mode menu appears on the screen. Select 
4.  Computer by using the  or  key and press the OK 
button  
.
The PC starts to detect the connection while the LCD...