HP Photosmart D5363 User Manual

To load up to 13 x 18 cm (5 x 7 inch) photo paper in the photo tray
1. Raise the photo tray lid to load photo paper in the photo tray.
2. Insert the stack of photo paper into the photo tray with the short edge forward and the
print side down. Slide the stack of photo paper forward until it stops.
If the photo paper you are using has perforated tabs, load the photo paper so that the
tabs are closest to you.
3. Slide the paper-length and paper-width guides inward against the stack of photo
paper until the...

3.Slide the paper-length and paper-width guides inward against the stack of cards until
the guides stop.
Do not overload the photo tray; make sure the stack of cards fits within the photo tray
and is no higher than the top of the paper-width guide.
4.Lower the photo tray lid.
Related topics
“
Change the print settings for the current job” on page 28
Load envelopes
You can load one or more envelopes into the main input tray of the HP Photosmart. Do
not use shiny or embossed envelopes or envelopes that...

5.Lower the output tray.
6. Pull the output tray extender towards you, as far as it will go.
Related topics
“
Change the print settings for the current job” on page 28
Load other types of paper
The following types of paper are designed for special projects. Create your project in the
HP Photosmart Software or another application, set the paper type and size, and then
print.
HP Premium Inkjet Transparency Film and HP Premium Plus Inkjet Transparency
Film
▲ Insert the film so that the white transparency...

HP CD/DVD Tattoo labels
▲Place one sheet of CD/DVD tattoo paper in the input tray with the print side down;
slide the CD/DVD tattoo paper forward until it stops.
NOTE: When you use CD/DVD tattoo labels, leave the tray extender closed.
Related topics
•“
Change the print settings for the current job” on page 28
•“
Recommended papers for printing” on page 15
Load a CD/DVD
In addition to printing on paper, the HP Photosmart enables you to print directly on the
surface of specially coated CDs and DVDs for...

2.Securely snap the inkjet printable media onto the CD/DVD holder with the printable
side up. The CD/DVD should be placed on the ring at the end of the holder with the
arrows.
NOTE: If you are using a smaller-sized media, flip the CD/DVD holder ring over
the CD/DVD.
3. Lower the CD/DVD tray.
The CD/DVD tray is located just below the control panel. When in its lowered position,
the CD/DVD tray sits on top of the output tray.
Chapter 6
24 Load paper
Load paper
 

4.Push the CD/DVD holder into the HP Photosmart until the lines on the CD/DVD holder
line up to the white lines on the CD/DVD tray.
NOTE: The HP Photosmart pulls the CD/DVD holder while printing on the media.
The CD/DVD holder might protrude about 7.5 cm (3 inches) at the back of the
device. If the HP Photosmart is placed close to a wall, move it at least 3 inches
away from the wall.
NOTE: Refer to the software that came with the HP Photosmart for printing on CD/
DVDs.
Avoid paper jams
To help avoid...

Chapter 6
26 Load paper
Load paper
 

7 Print from your computer
The HP Photosmart can be used with any software application that allows printing. You
can print a range of projects, such as borderless images, newsletters, greeting cards,
iron-on transfers, and posters.
You can also automatically print on both sides of the page using the Two-sided printing
accessory included with the HP Photosmart to print brochures and booklets, or just save
paper.
This section contains the following topics:
•
Print from a software application
•
Make the HP...

5.Select the appropriate options for your print job by using the features available in the
Advanced , Printing Shortcuts , Features , and Color  tabs.
TIP: You can easily select the appropriate options for your print job by choosing
one of the predefined print tasks on the  Printing Shortcuts tab. Click a type of
print task in the  Printing Shortcuts  list. The default settings  for that type of print
task are set and summarized on the  Printing Shortcuts tab. If necessary, you
can adjust the settings...

To set the paper size
1.Make sure you have paper loaded in the input tray.
2. On the  File menu in your software application, click  Print.
3. Make sure the HP Photosmart is the selected printer.
4. Click the button that opens the  Properties dialog box.
Depending on your software application, this button might be called  Properties,
Options , Printer Setup , Printer , or Preferences .
5. Click the  Features  tab.
6. In the  Resizing Options  area, from the Size drop-down list, select  More.
7. Select...