HP Photosmart C4583 User Manual

If this did not solve the issue, try the next solution.
Solution 4: Check the printer driver statusSolution: The printer driver status might have changed to either  offline or stop
printing .
To check the printer driver status
▲ In the HP Solution Center, click the  Status tab.
Cause: The status of the printer driver had changed.
If this did not solve the issue, try the next solution.
Solution 5: Wait until the product completes the current operation
Solution: If the product is performing another task...

If this did not solve the issue, try the next solution.
Solution 8: Make sure the print carriage can move freelySolution: Unplug the power cable if it is not already unplugged. Check to see if the
print cartridge carriage will move freely from one side of the printer to the other. Do
not try to force it to move if it is hung up on something.
CAUTION: Be careful not to force the print ca rtridge carriage. If the carriage is
stuck, forcing it to move will damage the printer.
For more information, see:
“...

Solution 10: Reset the productSolution: Turn off the product, and then unplug the power cord. Plug the power
cord back in, and then press the On button to turn on the product.
Cause: The product experienced an error.
The pages in my document came out in the wrong order
Solution: Print the document in reverse order. When the document finishes
printing, the pages will be in correct order.
For more information, see:
“
Print a multiple-page document in reverse order” on page 57
Cause: The print settings...

Solution 2: Verify the paper size setting
Solution: Verify that you have selected the proper paper size setting for your
project. Make sure that you have loaded the correct paper size in the input tray.
Cause: The paper size setting might not have been set correctly for the project you
were printing.
If this did not solve the issue, try the next solution.
Solution 3: Load the stack of paper correctly
Solution: Remove the stack of paper from the input tray, reload the paper, and then
slide the paper...

•Solution 4: Try printing with borders
Solution 1: Check th e margin settings
Solution: Check the printer margins.
Make sure the margin settings for the document do not exceed the printable area of
the product.
To check your margin settings
1. Preview your print job before sending it to the product.
In most software a pplications, click the  File menu, and then click  Print Preview.
2. Check the margins.
The product uses the margins you have set in your software application, as long
as they are greater...

Remove the stack of paper from the input tray, and then reload the paper.
For more information, see:
“
Load full-size paper or small-size photo paper” on page 34
Cause: The paper was loaded incorrectly.
If this did not solve the issue, try the next solution.
Solution 4: Try printing with borders
Solution: Try printing with borders by turning off the borderless option.
For more information, see:
“
Print a borderless image” on page 50
Cause: Borderless printing was enabled. By selecting the  Borderless...

Solution 3: Check the print cartridgeSolution: Check each print cartridge. The tape might have been removed from the
copper-colored contacts, but still might cover the ink nozzles. If the tape is still
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not
touch the ink nozzles or the copper-colored contacts.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Cause: The protective plastic tape was only...

•The On button is blinking
•
The product does not read the memory card
•
The photos on the memory card do not transfer to my computer
•
Solution 5: To map the memory card to a network drive in windows
My memory card no longer works in my digital camera Solution: Reformat your memory card in your  camera or format your memory card
on a Windows computer by selecting the FAT format. For more information, see the
documentation that came with your digital camera.
Cause: You formatted the card on a Windows XP...

Solution 2: Remove the additional memory cardSolution: Remove one of the memory cards. You can use only one memory card
at a time.
For more information, see:
“
Insert a memory card” on page 63
Cause: You had inserted more  than one memory card.
The product does not read the memory card
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the...

Solution 3: Remove the additional memory cardSolution: You can insert only one memory card at a time.
If more than one memory card is inserted, the green Photo light (near the memory
card slots) will blink rapidly, and an error message will appear on the computer screen.
Remove the additional memory card to resolve the problem.
Cause: You had inserted more than one memory card.
If this did not solve the issue, try the next solution.
Solution 4: Reformat the memory card in your digital camera Solution:...