HP PhotoSmart C4283 User Manual

							
To replace the print cartridges
1.Make sure the HP All-in-One is on.
CAUTION: If the HP All-in-One is off when you open the print cartridge door to
access the print cartridges, the HP All-in-One will not release the cartridges for
changing. You might damage the HP All-in-One if the print cartridges are not
docked safely when you  try to remove them.
2.Make sure you have letter or A4 unused plain white paper loaded in the input tray.
3. Open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
4.Wait until the print carriage is idle and silent, and then lightly press down on a print
cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the
slot on the left.
If you are replacing the black or photo print cartridge, remove the print cartridge from
the slot on the right.
1Print cartridge slot for the tri-color print cartridge
2Print cartridge slot for the black and photo print cartridges
5.Pull the print cartridge toward you out of its slot.
6. If you are removing the black print cartridge in order to install the photo print cartridge,
store the black print cartridge in the print cartridge protector or an airtight plastic
container.
Chapter 11
68 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
7.Remove the new print cartridge from its packaging and, being careful to touch only
the black plastic, gently remove the plastic tape by using the pink pull tab.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching
these parts can result in clogs, ink failure, and bad electrical connections.
8. Slide the new print cartridge forward into the empty slot. Then gently push the upper
part of the print cart ridge forward until it  clicks into the socket.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black or photo print cartridge, slide it into the right slot.
Work with print cartridges 69
Maintain the HP All-in-One
 
						

							
9.Close the print cartridge door.
If you installed a new print cartridge, the HP All-in-One prints a print cartridge
alignment page.
10. When prompted, ensure plain white paper is loaded in the input tray, then press the
button next to  OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
11. Place the page print side down on the scanner glass and then press the button next
to OK  to scan the page.
When the  On button stops flashing, the alignment is complete and the page can be
removed.
Related topics
“
Align the print cartridges” on page 71
Use a photo print cartridge
You can optimize the quality of the color photos you print and copy with the HP All-in-
One by purchasing a photo print cartridge. Remove the black print cartridge and insert
the photo print cartridge in its place. With the tri-color print cartridge and photo print
cartridge installed,  you have a six-ink system, which  provides enhanced quality color
photos.
When you want to print regular text documents, swap the black print cartridge back in.
Use a print cartridge protector or an airtight  plastic container to keep your print cartridge
secure when it is not being used.
Related topics
•“
Order print cartridges” on page 77
•“
Replace the print cartridges” on page 67
•“
Use the print cartridge protector” on page 70
Use the print cartridge protector
In some countries/regions, when you purchase a photo print cartridge, you might also
receive a print cartridge protector. In other countries/regions, a print cartridge protector
comes in the box with the HP All-in-One. If neither your print cartridge nor the HP All-in-
Chapter 11
70 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
One came with a print cartridge protector, you can use an airtight plastic container to
protect your print cartridge.
NOTE:If you use a plastic container, make sure the ink nozzles on the print cartridge
do not touch the plastic.
The print cartridge protector is designed to keep a print cartridge secure and prevent it
from drying out when it is not being used. Whenever you remove a print cartridge from
the HP All-in-One with the intention of using it again later, store it in the print cartridge
protector. For example, store the black print ca rtridge in a print cartridge protector if you
are removing it so you can print high-quality photos with the photo and tri-color print
cartridges.
To insert a print cartridge into the print cartridge protector
▲ Place the print cartridge into the print cartridge protector at a slight angle and snap it
securely into place.
To remove the print cartridge from the print cartridge protector
▲Press down on the top of the print cartridge protector to release the print cartridge,
then gently remove the print cartridge out of the print cartridge protector.
Align the print cartridges
When a new print cartridge is installed, the HP All-in-One aligns the cartridge. You can
also align the print cartridges at any time from software you installed with the HP All-in-
One. Aligning the print cartridges ensures high-quality output.
Work with print cartridges 71
Maintain the HP All-in-One
 
						

							
NOTE:If you remove and reinstall the same print cartridge, the HP All-in-One will
not prompt you to align the print cartridges. The HP All-in-One remembers the
alignment values for that print cartridge, so you do not need to realign the print
cartridges.
To align newly installed print cartridges
1. When prompted, ensure plain white letter or A4 paper is loaded in the input tray, then
press the button next to  OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
2. Place the page print side down on the scanner glass and then press the button next
to OK  to scan the page.
When the  On button stops flashing, the alignment is complete and the page can be
removed.
To align the print cartridges from the HP Photosmart Software
1. In the HP Solution Center, click  Settings, point to  Print Settings , and then click
Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Services tab, and then click
Service this device .
The Printer Toolbox  appears.
2. Click the  Device Services  tab.
3. Click  Align the Print Cartridges .
The HP All-in-One prints a print cartridge alignment sheet.
4. When prompted, ensure plain white letter or A4 paper is loaded in the input tray, then
press the button next to  OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
5. Place the page print side down on the scanner glass and then press the button next
to OK  to scan the page.
When the  On button stops flashing, the alignment is complete and the page can be
removed.
Related topics
“
Control panel buttons” on page 8
Clean the print cartridges
Use this feature when the self-test report shows streaking, white lines through any of the
lines of color or when a color is muddy after installing a print cartridge for the first time.
Do not clean print cartridges unnecessarily, as this wastes ink and shortens the life of the
ink nozzles.
Chapter 11
72 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
To clean the print cartridges from the HP Photosmart Software
1.Load letter, A4, or legal unused plain white paper into the input tray.
2. In the HP Solution Center, click  Settings, point to  Print Settings , and then click
Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Services tab, and then click
Service this device .
The Printer Toolbox  appears.
3. Click the  Device Services  tab.
4. Click  Clean the Print Cartridges .
5. Follow the prompts until you are satisfied with the quality of the output, and then
click  Done .
If copy or print quality still seems poor after you clean the print cartridges, try cleaning
the print cartridge contacts before replacing the affected print cartridge.
Related topics
•“
Clean the print cartridge contacts” on page 73
•“
Replace the print cartridges” on page 67
Clean the print cartridge contacts
Clean the print cartridge contacts if you get repeated messages on your computer screen
prompting you to check a print cartridge after you already have cleaned or aligned the
print cartridges, or if the Check Print Cartridge light is blinking.
Before cleaning the print cartridge contacts, remove the print cartridge and verify that
nothing is covering the print cartridge contacts, then reinstall the print cartridge. If you
continue to get messages to check the print cartridges, clean the print cartridge contacts.
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
TIP: Coffee filters are lint-free and work well for cleaning print cartridges.
•Distilled, filtered, or bottled water (tap water might contain contaminants that can
damage the print cartridges).
CAUTION: Do not use platen cleaners or alcohol to clean the print cartridge
contacts. These can damage the print cartridge or the HP All-in-One.
To clean the print cartridge contacts
1. Turn on the HP All-in-One and open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
2. Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the HP All-in-One.
Work with print cartridges 73
Maintain the HP All-in-One
 
						

							
3.Lightly press down on the print cartridge to release it, and then pull it toward you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the HP All-
in-One for more  than 30 minutes.
4.Inspect the print cartridge contacts for ink and debris buildup.
5. Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any
excess water from it.
6. Hold the print cartridge by its sides.
7. Clean only the copper-colored contacts. Allow the print cartridges to dry for
approximately ten minutes.
1Copper-colored contacts
2Ink nozzles (do not clean)
8.Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks
into place.
9. Repeat if necessary for the other print cartridge.
10. Gently close the print cartridge door and plug the power cord into the back of the
HP All-in-One.
Related topics
•“
Clean the area around the ink nozzles” on page 74
•“
Replace the print cartridges” on page 67
Clean the area around the ink nozzles
If the HP All-in-One is used in a dusty environment, a small amount of debris might
accumulate inside the device. This debris can include dust, hair, carpet, or clothing fibers.
When debris gets on the print cartridges, it can cause ink streaks and smudges on printed
pages. Ink streaking can be corrected by cleaning around the ink nozzles as described
here.
Chapter 11
74 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
NOTE:Clean the area around the ink nozzles only if you continue to see streaks
and smudges on your printed pages after you have already cleaned the print
cartridges by using the software you installed with the HP All-in-One.
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
TIP: Coffee filters are lint-free and work well for cleaning print cartridges.
•Distilled, filtered, or bottled water (tap water might contain contaminants that can
damage the print cartridges).
CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching
these parts can result in clogs, ink failure, and bad electrical connections.
To clean the area around the ink nozzles
1. Turn on the HP All-in-One and open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
2. Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the HP All-in-One.
3. Lightly press down on the print cartridge to release it, and then pull it toward you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the HP All-
in-One for more than 30 minutes.
4. Place the print cartridge on a piece of paper with the ink nozzles facing up.
5. Lightly moisten a clean foam rubber swab with distilled water.
6. Clean the face and edges around the ink nozzle area with the swab, as shown below.
1Nozzle plate (do not clean)
2Face and edges around the ink nozzle area
CAUTION: Do not clean the nozzle plate.
7. Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks
into place.
Work with print cartridges 75
Maintain the HP All-in-One
 
						

							
8.Repeat if necessary for the other print cartridge.
9. Gently close the print cartridge door and plug the power cord into the back of the
HP All-in-One.
Related topics
“
Clean the print cartridges” on page 72
Remove ink from your skin and clothing
Follow these instructions to remove ink from your skin and clothing:
SurfaceRemedy
SkinWash the area with an abrasive soap.
White fabricWash the fabric in  cold water and use chlorine bleach.
Color fabricWash the fabric in  cold water and use sudsy ammonia.
CAUTION: Always use cold water to remove ink from fabric. Warm or hot water can
set the ink into the fabric.
Chapter 11
76 Maintain the HP All-in-One
Maintain the HP All-in-One
 
						

							
12 Shop for printing supplies
You can order HP products, such as recommended types of paper and print cartridges,
online from the HP Web site.
This section contains the following topics:
•
Order paper or other media
•
Order print cartridges
•
Order other supplies
Order paper or other media
To order HP papers and other supplies, such as HP Premium Photo Papers or HP All-
in-One Paper, go to 
www.hp.com/buy/supplies . If prompted, choose your country/region,
follow the prompts to select your product, and then click one of the shopping links on the
page.
Order print cartridges
For a list of print cartridge numbers, see the printed documentation that came with the
HP All-in-One. You can also use the software  that came with the HP All-in-One to find
out the reorder number for all the print cartridges. You can order print cartridges online
from the HP Web site. Additionally, you can contact a local HP reseller to find out the
correct print cartridge reorder numbers for your device and purchase print cartridges.
To order HP papers and other supplies, go to 
www.hp.com/buy/supplies . If prompted,
choose your country/region, follow the prompts to select your product, and then click one
of the shopping links on the page.
NOTE: At this time, some portions of the HP Web site are available in English only.
NOTE:Ordering print cartridges online is not supported in all countries/regions. If it
is not supported in your country/region, contact a local HP reseller for information
about purchasing print cartridges.
To order print cartridges through the HP Photosmart Software
1. In the HP Solution Center, click  Settings, point to  Print Settings , and then click
Printer Toolbox .
NOTE:You can also open the  Printer Toolbox from the Print Properties  dialog
box. In the  Print Properties  dialog box, click the  Services tab, and then click
Service this device .
2.Click the  Estimated Ink Levels  tab.
Shop for printing supplies 77
Shop for printing supplies