HP Pavilion Hdx9575la Entertainment Notebook Pc Service Guide

							7.Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.
Component replacement procedures 53 
						

							Keyboard
Description
For use in:
Spare part numberFor use in:Spare part number
Denmark, Finland, Norway, and
Sweden448159-DH1Latin America448159-161
France448159-051South Korea448159-AD1
French Canada448159-121Spain448159-071
Germany448159-041The United Kingdom448159-031
The Netherlands and Europe448159-B31The United States448159-001
Italy 448159-061   
Before removing the keyboard, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the hard drives (see 
Hard drive on page 45).
Remove the keyboard:
1.Position the computer with the front toward you.
2.Remove the three Phillips PM2.5×8.0 screws (1) and the four Phillips PM2.5×5.0 screws (2) that
secure the keyboard to the computer.
3.Turn the computer display-side up, with the front toward you.
54 Chapter 4   Removal and replacement procedures 
						

							4.Open the computer as far as possible.
5.Lift the front edge of the keyboard (1) until it rests at an angle.
6.Slide the keyboard (2) forward until the tabs on the rear edge of the keyboard disengage from the
slots in the top cover.
7.Rotate the rear edge of the keyboard (3) forward until it rests upside down on the palm rest.
8.Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached and
disconnect the keyboard cable (2).
9.Remove the keyboard.
Reverse this procedure to install the keyboard.
Component replacement procedures 55 
						

							Hinge cover
DescriptionSpare part number
Hinge cover452311-001
Before removing the hinge cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
Remove the hinge cover:
1.Position the computer with the rear panel toward you.
2.Remove the four gray rubber screw covers (1) and (2) from the hinge cover. The screw covers come
in two different sizes and are available in the Rubber Feet Kit, spare part number 452320-001.
3.Remove the four Phillips PM3.0×8.0 screws (3) that secure the hinge cover to the computer.
4.Remove the hinge cover (4) by pulling it away from the computer.
Reverse this procedure to install the hinge cover.
56 Chapter 4   Removal and replacement procedures 
						

							Rear cover
DescriptionSpare part number
Rear cover448161-001
Before removing the rear cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the hinge cover (see 
Hinge cover on page 56).
Remove the rear cover:
1.Position the computer with the front toward you.
2.Remove the seven Phillips PM2.5×8.0 screws (1) that secure the rear cover to the computer.
3.Remove the Mylar screw cover (2) in the optical drive bay. This screw cover is available in the Rubber
Feet Kit, spare part number 452320-001.
4.Remove the Phillips PM2.5×4.0 screw (3) that secures the rear cover to the computer.
5.Remove the four Phillips PM3.0×12.0 screws (1) that secure the rear cover to the computer.
Component replacement procedures 57 
						

							6.Remove the four Phillips PM2.5×4.0 broad-head screws (2) that secure the rear cover to the
computer.
7.Turn the computer right-side up, with the front toward you.
8.Open the computer as far as possible.
9.Remove the rear cover.
Reverse this procedure to install the rear cover.
58 Chapter 4   Removal and replacement procedures 
						

							Top cover
DescriptionSpare part number
Top cover (includes TouchPad board cable and TouchPad button cable, and LED boards and cables) 448174-001
Before removing the top cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
Remove the top cover:
1.Turn the computer upside down, with the front toward you.
2.Remove the two Mylar screw covers (1) in the optical drive bay. These screw covers are available
in the Rubber Feet Kit, spare part number 452320-001.
3.Remove the two Phillips PM2.5×4.0 screws (2) and the ten Phillips PM2.5×8.0 screws (3) that secure
the top cover to the computer.
Component replacement procedures 59 
						

							4.Remove the four Phillips PM2.5×5.0 screws (1) and the two Phillips PM2.5×11.0 screws (2) that
secure the top cover to the computer.
5.Turn the computer right-side up, with the front toward you.
6.Open the computer as far as possible.
7.Disconnect the following cables:
(1) Fingerprint reader board cable
(2) LED board cable
(3) TouchPad board cable
(4) TouchPad on/off board cable
8.Remove the two Phillips PM2.5×5.0 screws (1) that secure the top cover to the computer.
60 Chapter 4   Removal and replacement procedures 
						

							9.Lift the rear edge of the top cover (2) until the top cover disengages from the computer.
10.Remove the top cover.
Reverse this procedure to install the top cover.
Fingerprint reader board
DescriptionSpare part number
Fingerprint reader board (includes cable) 448166-001
Before removing the fingerprint reader board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
Component replacement procedures 61 
						

							Remove the fingerprint reader board:
1.Turn the top cover upside down, with the front toward you.
2.Remove the two silver Phillips PM2.0×4.0 screws (1) that secure the fingerprint reader board and
bracket to the top cover.
3.Remove the fingerprint reader board bracket (2) and fingerprint reader board (3).
Reverse this procedure to install the fingerprint reader board.
TouchPad on/off board
DescriptionSpare part number
TouchPad on/off board (includes cable) 448167-001
Before removing the TouchPad on/off board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
62 Chapter 4   Removal and replacement procedures