HP Pavilion Hdx9100 Entertainment Notebook Pc Series Service Guide

							Processor heat sink
DescriptionSpare part number
Processor heat sink (includes replacement thermal material) 448175-001
Before removing the processor heat sink, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
g.Subwoofer (see 
Subwoofer on page 72)
h.System board (see 
System board on page 76)
Remove the processor heat sink:
1.Turn the system board upside down, with the front toward you.
2.Loosen the three silver Phillips PM2.0×5.0 captive screws (1) that secure the processor heat sink to
the system board.
3.Remove the processor heat sink clip (2) by sliding it to the right.
Component replacement procedures 83 
						

							4.Remove the processor heat sink (3).
NOTE:Due to the adhesive quality of the thermal material located between the processor heat sink
and system board components, it may be necessary to move the processor heat sink from side to
side to detach it.
NOTE:The thermal material must be thoroughly cleaned from the surfaces of the processor heat
sink (1) and the system board (2) each time the processor heat sink is removed. Thermal material
must be installed on all surfaces before the processor heat sink is reinstalled. Replacement thermal
material is included with all processor heat sink, system board, and processor spare part kits, and
is also available using spare part number 413706-001.
Reverse this procedure to install the processor heat sink.
84 Chapter 4   Removal and replacement procedures 
						

							Processor
NOTE:All processor spare part kits include replacement thermal material.
DesriptionSpare part number
Intel Core 2 Extreme processors (4-MB L2 cache, 800-MHz FSB, 44-W):
X7900 2.8-GHz processor
453908-001
X7800 2.6-GHz processor455738-001 and
452327-001
Intel Core 2 Duo processors (4-MB L2 cache, 800-MHz FSB, 35-W):
T7700 2.4-GHz processor
448148-001
T7500 2.2-GHz processor448147-001
T7300 2.0-GHz processor448146-001
T7100 1.8-GHz processor448149-001
Before removing the processor, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
g.Subwoofer (see 
Subwoofer on page 72)
h.System board (see 
System board on page 76)
i.Processor heat sink (see 
Processor heat sink on page 83)
Remove the processor:
1.Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
Component replacement procedures 85 
						

							2.Lift the processor (2) straight up and remove it.
NOTE:The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor slot when you install the processor.
Reverse this procedure to install the processor.
86 Chapter 4   Removal and replacement procedures 
						

							Video board heat sink
DescriptionSpare part number
Video board heat sink (includes replacement thermal material) 448176-001
Before removing the video board heat sink, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
g.Subwoofer (see 
Subwoofer on page 72)
h.System board (see 
System board on page 76)
Remove the video board heat sink:
1.Turn the system board upside down, with the front toward you.
2.Disconnect the video board fan cable (1) from the system board.
3.Loosen the two Phillips PM2.5×9.0 captive screws (2) and the four silver Phillips PM2.0×5.0 captive
screws (3) that secure the video board heat sink to the system board.
Component replacement procedures 87 
						

							4.Remove the video board heat sink (4).
NOTE:Due to the adhesive quality of the thermal material located between the video board heat
sink and system board components, it may be necessary to move the video board heat sink from
side to side to detach it.
NOTE:The thermal material must be thoroughly cleaned from the surfaces of the video board
components (1) and the video board heat sink (2) each time the video board heat sink is removed.
Thermal material must be installed on all surfaces before the video board heat sink is reinstalled.
Replacement thermal material is included with all video board heat sink and video board spare part
kits, and is also available using spare part number 413706-001.
Reverse this procedure to install the video board heat sink.
88 Chapter 4   Removal and replacement procedures 
						

							Video board fan
DescriptionSpare part number
Video board fan448163-001
NOTE:To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left and
right sides and rear panel of the computer. The computer uses two electric fans for ventilation. The fans
are controlled by a temperature sensor and are designed to turn on automatically when high temperature
conditions exist. These conditions are affected by high external temperatures, system power consumption,
power management/battery conservation configurations, battery fast charging, and software
requirements. Exhaust air is displaced through the ventilation grills located on the computer rear panel.
Before removing the video board fan, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
g.Subwoofer (see 
Subwoofer on page 72)
h.System board (see 
System board on page 76)
i.Video board heat sink (see 
Video board heat sink on page 87)
Remove the video board fan:
1.Turn the video heat sink upside down.
2.Remove the three black Phillips PM2.0×4.0 screws (1) that secure the video board fan to the video
board heat sink.
Component replacement procedures 89 
						

							3.Remove the video board fan (2).
Reverse this procedure to install the video board fan.
Video board
DescriptionSpare part number
nVidia video board (includes replacement thermal material) 454311-001
Before removing the video board fan, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 38).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 45)
b.Optical drive (see 
Optical drive on page 52)
c.Keyboard (see 
Keyboard on page 54)
d.Hinge cover (see 
Hinge cover on page 56)
e.Rear cover (see 
Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
g.Subwoofer (see 
Subwoofer on page 72)
90 Chapter 4   Removal and replacement procedures 
						

							h.System board (see System board on page 76)
i.Video board heat sink (see 
Video board heat sink on page 87)
Remove the video board:
1.Remove the two Phillips PM2.5×4.0 screws (1) that secure the video board to the system board.
2.Lift the right side of the video board (2) until it rests at an angle.
3.Remove the video board (3) by pulling it away from the video board slot at an angle.
NOTE:Video boards are designed with a notch (4) to prevent incorrect installation into the video
board slot.
Reverse this procedure to install the video board.
Component replacement procedures 91 
						

							5
Computer Setup
Starting Computer Setup
Computer Setup is a ROM-based information and customization utility that can be used even when the
Windows operating system is not working or will not load.
NOTE:The fingerprint reader does not work when accessing Computer Setup.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start Computer Setup:
1.Turn on or restart the computer.
2.Before Windows opens and while F10 = ROM Based Setup is displayed in the lower-left corner
of the screen, press f10.
92 Chapter 5   Computer Setup