HP Pavilion Hdx9000 Entertainment Notebook Pc Series Service Guide

e.Rear cover (see Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
Remove the TouchPad on/off board:
1.Turn the top cover upside down, with the front toward you.
2.Remove the two silver Phillips PM2.0×4.0 screws (1) that secure the TouchPad on/off board to the
top cover.
3.Remove the TouchPad on/off board (2).
Reverse this procedure to install the TouchPad on/off board.
Component replacement procedures 63 

Display assembly
DescriptionSpare part number
20.1-inch, WSXGA BrightView display assembly (includes camera module and cable, microphones,
speakers, and WLAN antennae)452299-001
20.1-inch, WUXGA BrightView display assembly (includes camera module and cable, microphones,
speakers, and WLAN antennae)452300-001
Before removing the display assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down...

2.Remove the six Phillips PM3.0×8.0 screws that secure the display assembly to the computer.
3.Turn the computer display-side up, with the front toward you.
4.Open the computer to an upright position.
5.Disconnect the following cable connectors:
(1) Display panel cable
(2) Camera module cable
(3) Speaker cable
(4) Microphone cable
NOTE:The speaker cables are black and red and share a single connector. The microphone cables
are gray and white and share a single connector. Be sure that these connectors are...

6.Remove the WLAN antenna cables (5) from the opening in the system board.
CAUTION:The display assembly will be unsupported when the following screws are removed. To
prevent damage to the display assembly, support the display assembly before removing the screws.
7.Remove the six Phillips PM3.0×8.0 screws (1) that secure the display assembly to the computer.
8.Remove the display assembly (2).
NOTE:If it is necessary to replace any of the display assembly internal components, see Display
assembly internal...

Audio/infrared board
DescriptionSpare part number
Audio/infrared board452316-001
Before removing the audio/infrared board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the...

Reverse this procedure to install the audio/infrared board.
Bluetooth module
NOTE:The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is available in the Cable Kit, spare part number 448169-001.
DescriptionSpare part number
Bluetooth module398393-002
Before removing the Bluetooth module, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the...

3.Remove the Bluetooth module (3) from the base enclosure.
Reverse this procedure to install the Bluetooth module.
Front USB board
DescriptionSpare part number
Front USB board452314-001
Before removing the front USB board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer...

Remove the front USB board:
1.Disconnect the front USB board cable (1) from the system board.
2.Remove the two Phillips PM2.5×4.0 screws (2) that secure front USB board the to the computer.
3.Remove the front USB board (3).
Reverse this procedure to install the front USB board.
Power connector LED board
DescriptionSpare part number
Power connector LED board (includes cable) 452318-001
Before removing the power connector LED board, follow these steps:
1.Shut down the computer. If you are unsure whether...

e.Rear cover (see Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
Remove the power connector LED board:
1.Disconnect the power connector LED board (1) from the system board.
2.Remove the power connector LED board (2).
Reverse this procedure to install the power connector LED board.
Rear USB board
DescriptionSpare part number
Rear USB board (includes cable) 452315-001
Before removing the rear USB board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is...

e.Rear cover (see Rear cover on page 57)
f.Top cover (see 
Top cover on page 59)
Remove the rear USB board:
1.Disconnect the rear USB board cable (1) from the system board.
2.Remove the Phillips PM2.5×4.0 screw (2) that secures rear USB board the to the computer.
3.Remove the rear USB board (3).
Reverse this procedure to install the rear USB board.
Subwoofer
DescriptionSpare part number
Subwoofer (includes rubber isolators) 448164-001
Before removing the subwoofer, follow these steps:
1.Shut down the...