HP Pavilion Dv7t 3300 Cto Entertainment Notebook Pc Manual

							Removal and replacement procedures
Maintenance and Service Guide4–15
Before removing the WLAN module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the primary hard drive cover (see “Primary hard drive cover” on page 4-9).
Remove the WLAN module: 
Ä
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the 
computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and 
then receive a warning message, remove the module to restore computer functionality, and then contact technical support through 
Help and Support.
1. Disconnect the WLAN antenna cables 1 from the WLAN module.
✎The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN antenna 
cable is connected to the WLAN module “Aux” terminal.
2. Remove the two Phillips PM2.0×4.0 screws 2 that secure the WLAN module to the computer. (The edge of the 
module opposite the slot rises away from the computer.)
Intel 5100 802.11a/b/g Half-Mini Card WLAN modules:
■For use in Andorra, Antigua and Barbuda, Argentina, Aruba, Australia, Austria, Azerbaijan, the 
Bahamas, Bahrain, Barbados, Belgium, Bermuda, Bolivia, Bosnia and Herzegovina, Brazil, 
Brunei, Bulgaria, Canada, Cayman Islands, Chile, Colombia, Costa Rica, Croatia, Cyprus, the 
Czech Republic, Denmark, the Dominican Republic, Ecuador, Egypt, El Salvador, Estonia, 
Finland, France, French Guiana, Georgia, Germany, Ghana, Greece, Guadeloupe, Guam, 
Guatemala, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, 
the Ivory Coast, Jamaica, Japan, Jordan, Kenya, Kuwait, Kyrgyzstan, Latvia, Lebanon, 
Martinique, Puerto Rico, Nether Antilles, Liechtenstein, Lithuania, Luxembourg, Malawi, 
Malaysia, Malta, Mauritius, Mexico, Monaco, Montenegro, Morocco, the Netherlands, New 
Zealand, Nicaragua, Nigeria, Norway, Oman, Pakistan, Panama, Paraguay, the Peoples 
Republic of China, Peru, the Philippines, Poland, Portugal, Qatar, Romania, San Marino, Saudi 
Arabia, Senegal, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, 
Sweden, Switzerland, Taiwan, Tanzania, Thailand, Trinidad and Tobago, Turkey, the United Arab 
Emirates, the United Kingdom, Uruguay, U.S. Virgin Islands, the United States, Venezuela, 
Vietnam572507-001
■For use in Russia and Ukraine 572508-001 DescriptionSpare part number  
						

							4–16Maintenance and Service Guide
Removal and replacement procedures
3. Remove the WLAN module 3 by pulling it away from the slot at an angle.
✎WLAN modules are designed with a notch 4 to prevent incorrect insertion into the WLAN module slot.
Reverse this procedure to install the WLAN module. 
RTC battery 
Before removing the RTC battery, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the primary hard drive cover (see “Primary hard drive cover” on page 4-9).
Remove the RTC battery: 
»Remove the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery. Be sure the RTC battery is installed with the “+” sign facing up.
Description Spare part number 
RTC battery 449729-001  
						

							Removal and replacement procedures
Maintenance and Service Guide4–17
Memory module
Before removing the memory module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the primary hard drive cover (see “Primary hard drive cover” on page 4-9).
Remove the memory module:
✎The top memory module slot is for extension memory and the bottom slot is for primary memory.
1. Spread the retaining tabs 1 on each side of the memory module to release the memory module. (The edge of 
the module opposite the slot rises away from the computer.) 
2. Remove the memory module 2 by pulling the module away from the slot at an angle. 
✎Memory modules are designed with a notch 3 to prevent incorrect insertion into the memory module slot.
Reverse this procedure to install a memory module. 
Description Spare part number 
4096-MB (DDR3, 1066-MHz) 575480-001
2048-MB (DDR3, 1066-MHz) 575479-001
1024-MB (DDR3, 1066-MHz) 575478-001 
						

							4–18Maintenance and Service Guide
Removal and replacement procedures
TV tuner module
✎The TV tuner module spare part kit does not include a TV tuner module cable. The TV tuner module cable is 
included in the Cable Kit, spare part number 516328-001.
✎The TV tuner external antenna cables are available using spare part numbers 482900-001 (with F-PAL jack) and 
482900-002 (with PAL jack).
Before removing the TV tuner module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6).
5. Remove the secondary hard drive cover (see “Secondary hard drive cover” on page 4-10).
Remove the TV tuner module: 
1. Disconnect the TV tuner module antenna cable 1 from the terminal on the TV tuner module. 
2. Remove the Phillips PM2.0×4.0 screw 2 that secures the TV tuner module to the computer. (The edge of the 
module opposite the slot rises away from the computer.)
3. Remove the TV tuner module 3.
✎The TV tuner module is designed with a notch 4 to prevent incorrect insertion into the TV tuner module slot.
Reverse this procedure to install the TV tuner module.
Description Spare part number 
DVB-T TV tuner module 482899-003
DVB-T/ANG TV tuner module 482899-002
ATSC/NTSC/QAM hybrid TV tuner module 482899-001 
						

							Removal and replacement procedures
Maintenance and Service Guide4–19
Switch cover and keyboard
Before removing the switch cover and keyboard, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the primary hard drive cover (see “Primary hard drive cover” on page 4-9). 
Remove the switch cover and keyboard: 
1. Turn the computer upside down, with the front toward you. 
2. Remove the following screws:
1 Three Phillips PM2.5×7.0 screws that secure the keyboard to the computer
2 Three Phillips PM2.5×7.0 screws that secure the switch cover to the computer
3 Four Phillips PM2.5×4.5 screws that secure the switch cover to the computer
Description: Spare part number 
Switch cover for use in white computers (includes LED board and cable) 516300-001
Switch cover for use in black computers (includes LED board and cable)  519269-001
White molded keyboard 516356-xxx
White painted keyboard 516357-xxx
Black molded keyboard 519265-xxx
Black painted keyboard 519266-xxx
✎For a detailed list of available keyboards, see “Sequential part number listing” on page 3-11. 
						

							4–20Maintenance and Service Guide
Removal and replacement procedures
3. Turn the computer display-side up, with the front toward you, and open the computer as far as possible.
4. Lift the rear edge of the switch cover until it detaches from the computer.
5. Remove the four Phillips PM2.0×4.0 screws 1 that secure the keyboard to the computer.
6. Lift the keyboard 2 until the keyboard connector on the system board is accessible. 
						

							Removal and replacement procedures
Maintenance and Service Guide4–21
7. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is connected and disconnect the 
cable 2 from the system board.
8. Remove the keyboard.
9. Disconnect the power button board cable 1 from the low insertion force (LIF) connector on the system board.
10. Disconnect the LED board cable 2 from the LIF connector on the system board.
11. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard. 
						

							4–22Maintenance and Service Guide
Removal and replacement procedures
Power button board
Before removing the power button board, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6).
5. Remove the switch cover and keyboard (see “Switch cover and keyboard” on page 4-19).
Remove the power button board: 
1. Turn the switch cover upside down with the front toward you. 
2. Remove the Phillips PM2.0×4.0 screw 1 that secures the power button board to the switch cover.
3. Remove the power button board 2 and cable.
Reverse this procedure to install the power button board.
Description Spare part number 
Power button board (includes cable) 516329-001 
						

							Removal and replacement procedures
Maintenance and Service Guide4–23
Speaker assembly 
Before removing the speaker assembly, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the switch cover and keyboard (see “Switch cover and keyboard” on page 4-19).
Remove the speaker assembly: 
1. Disconnect the speaker assembly cable 1 from the system board. 
2. Remove the speaker assembly 2.
Reverse this procedure to install the speaker assembly. 
Description Spare part number 
Speaker assembly  516323-001  
						

							4–24Maintenance and Service Guide
Removal and replacement procedures
Bluetooth module
Before removing the Bluetooth module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-6). 
5. Remove the switch cover and keyboard (see “Switch cover and keyboard” on page 4-19).
Remove the Bluetooth module: 
1. Disconnect the Bluetooth module cable 1 from the system board. 
2. Slide the Bluetooth module out of the slot 2.
3. Remove the module from the computer 3. 
Reverse this procedure to install the Bluetooth module. 
Description Spare part number 
Bluetooth module (does not include cable) 537921-001
Bluetooth module cable 583501-001