HP Pavilion Dv7 6c00 Entertainment Notebook Pc Series Manual

8 External cards and devices
Using Digital Media Slot cards (select models only)
Optional digital cards provide secure data storage and convenient data sharing. These cards are
often used with digital media–equipped cameras and PDAs as well as with other computers.
To determine the digital card formats that are supported on your computer, refer to 
Front on page 9.
Inserting a digital card
CAUTION:To reduce the risk of damage to the digital card connectors, use minimal force to insert
a digital card....

Removing a digital card
CAUTION:To reduce the risk of loss of data or an unresponsive system, use the following
procedure to safely remove the digital card.
1.Save your information and close all programs associated with the digital card.
2.Click the remove hardware icon in the notification area, at the far right of the taskbar. Then
follow the on-screen instructions.
3.Press in on the card (1), and then remove it from the slot (2).
NOTE:If the card does not eject, pull the card out of the slot.
Using a...

▲Connect the USB cable for the device to the USB port.
NOTE:The USB port on your computer may look slightly different from the illustration in this
section.
You will hear a sound when the device has been detected.
NOTE:The first time you connect a USB device, a message in the notification area lets you know
that the device is recognized by the computer.
Removing a USB device
CAUTION:To reduce the risk of damage to a USB connector, do not pull on the cable to remove
the USB device.
CAUTION:To reduce the...

Using optional external devices
NOTE:For more information about required software and drivers, or to learn which computer port to
use, refer to the manufacturers instructions.
To connect an external device to the computer:
CAUTION:To reduce the risk of damage to the equipment when connecting a powered device, be
sure that the device is turned off and the AC power cord is unplugged.
1.Connect the device to the computer.
2.If you are connecting a powered device, plug the device power cord into a grounded...

9 Drives
Handling drives
CAUTION:Drives are fragile computer components that must be handled with care. Refer to the
following cautions before handling drives. Additional cautions are included with the procedures to
which they apply.
Observe these precautions:
●Before you move a computer that is connected to an external hard drive, initiate Sleep and allow
the screen to clear, or properly disconnect the external hard drive.
●Before handling a drive, discharge static electricity by touching the unpainted...

Using hard drives
Improving hard drive performance
Using Disk Defragmenter
As you use the computer, files on the hard drive become fragmented. Disk Defragmenter
consolidates the fragmented files and folders on the hard drive so that the system can run more
efficiently.
NOTE:It is not necessary to run Disk Defragmenter on solid-state drives.
After you start Disk Defragmenter, it works without supervision. Depending on the size of your hard
drive and the number of fragmented files, Disk Defragmenter may...

A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal
operation.
NOTE:Because solid-state drives (SSD) lack moving parts, HP 3D DriveGuard is unnecessary.
NOTE:Hard drives in the primary hard drive bay or in the secondary hard drive bay are protected
by HP 3D DriveGuard. Hard drives connected to USB ports are not covered by HP 3D DriveGuard.
For more information, refer to the HP 3D DriveGuard software Help.
Identifying HP 3D DriveGuard status
The drive light...

Using HP 3D DriveGuard software
The HP 3D DriveGuard software can be enabled or disabled by an Administrator.
NOTE:Depending on your user privileges, you may be unable to enable or disable HP 3D
DriveGuard. Privileges for non-Administrator users can be changed by members of an Administrator
group.
To open the software and change settings, follow these steps:
1.In Mobility Center, click the hard drive icon to open the HP 3D DriveGuard window.
– or –
Select Start > Control Panel > Hardware and Sound > HP...

4.Slide the battery release latch (1) until the cover is released, and then lift up and remove the
cover (2).
5.Disconnect the hard drive cable (1), and then remove the 4 screws (2) from the hard drive.
6.Pull the hard drive tab upward to release the hard drive, and then lift the hard drive out of the
hard drive bay.
Adding or replacing a hard drive 59 

Replacing the hard drive
1.Insert the hard drive into the hard drive bay.
2.Replace the 4 screws (1) on the hard drive, and then connect the hard drive cable (2).
3.Align the tabs on the cover (1) with the notches on the computer, and then close the cover (2).
60 Chapter 9   Drives