HP Pavilion Dv7 2100 Entertainment Notebook Pc Series Manual

e.Display assembly (see Display assembly on page 64).
f.Top cover (see 
Top cover on page 74).
Remove the audio/infrared board:
1.Remove the Phillips PM2.5×5.0 screw (1) that secures the audio/infrared board to the base
enclosure.
2.Release the audio/infrared board cable from the clip (2) built into the base enclosure.
3.Lift the audio/infrared board (3) straight up.
4.Disconnect the audio/infrared board cable from the system board (4), and then remove the audio-
infrared board from the base enclosure....

4.Remove the battery (see Battery on page 43).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 48).
b.Optical drive (see 
Optical drive on page 44).
c.Switch cover and keyboard (see 
Switch cover and keyboard on page 57).
d.Speaker assembly (see 
Speaker assembly on page 62).
e.Display assembly (see 
Display assembly on page 64).
f.Top cover (see 
Top cover on page 74).
Remove the USB board:
1.Disconnect the USB board cable (1) from the LIF connector on the system board.
2.Remove...

3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 43).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 48).
b.Optical drive (see 
Optical drive on page 44).
c.Switch cover and keyboard (see 
Switch cover and keyboard on page 57).
d.Speaker assembly (see 
Speaker assembly on page 62).
e.Display assembly (see 
Display assembly on page 64)....

TV tuner module cable
NOTE:The TV tuner module cable is available in the Cable Kit, spare part number 516328-001.
Before removing the TV tuner module cable, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then...

3.Remove the assembly from the enclosure (3).
Reverse this procedure to install the TV tuner module cable.
Modem module cable
NOTE:The modem module cable is available in the Cable Kit, spare part number 516328-001. The
modem module cable includes the RJ-11 jack.
Before removing the modem module cable, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all...

1.Release the cable from the clips (1) built into the base enclosure.
2.Remove the RJ-11 jack (2) from the clip built into the base enclosure.
3.Remove the assembly from the base enclosure (3).
Reverse this procedure to install the modem module cable.
Power connector cable
DescriptionSpare part number
Power connector cable 536857-001
NOTE:The power connector cable is available in the Cable Kit, spare part number 501891-001.
Before removing the power connector cable, follow these steps:
1.Shut down the...

g.USB board (see USB board on page 83).
h.System board (see 
System board on page 79).
Remove the power connector cable:
1.Remove the Phillips PM2.5×7.0 screw (1) that secures the power connector and bracket (2) to the
base enclosure.
2.Remove the power connector cable (3).
Reverse this procedure to install the power connector cable.
Fan/heat sink assembly
NOTE:The fan/heat sink assembly spare kit includes replacement thermal material.
DescriptionSpare part number
For use only with computer models...

3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 43).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 48).
b.Optical drive (see 
Optical drive on page 44).
c.Switch cover and keyboard (see 
Switch cover and keyboard on page 57).
d.Speaker assembly (see 
Speaker assembly on page 62).
e.Display assembly (see 
Display assembly on page 64)....

4.Remove the fan/heat sink assembly (3).
NOTE:Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
NOTE:The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly and the system board each time the fan/heat sink assembly is removed. Thermal paste
is used on the processor (1) and the heat sink section...

8.Remove the fan/heat sink assembly (3).
NOTE:Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly
and the system board each time the fan/heat sink assembly is removed. Thermal paste is used on
capacitors and their contacts (1), on the processor...