HP Pavilion Dv6700 Entertainment Notebook Pc Series Service Guide

							Where used: 6 screws that secure the display bezel to the display assembly
Where used: One screw that secures the top cover to the computer
Where used: One screw that secures the top cover to the computer
Phillips PM2.5×5.0 screw 123 
						

							Phillips PM2.5×2.0 screw
ColorQuantityLengthThreadHead width
Silver 5 2.0 mm 2.5 mm 7.0 mm
Where used: 2 screws that secure the speaker assembly to the computer
Where used: 3 screws that secure the top cover to the computer
124 Chapter 7   Screw listing 
						

							Phillips PM2.5×4.0 screw
ColorQuantityLengthThreadHead width
Silver 18 4.0 mm 2.5 mm 5.0 mm
Where used: 6 screws that secure the display panel to the display assembly
Where used: 2 screws that secure the top cover to the computer
Phillips PM2.5×4.0 screw 125 
						

							Where used:
(1) Four screws that secure the ExpressCard assembly to the computer
(2) Two screws that secure the USB/power connector board to the computer
(3) Two screws that secure the system board to the computer
Where used: 2 screws that secure the audio board to the computer
126 Chapter 7   Screw listing 
						

							Hex HM5.0×9.0 standoff
ColorQuantityLengthThreadHead width
Silver 2 9.0 mm 2.5 mm 5.0 mm
Where used: 2 standoffs that secure the top cover to the computer
Hex HM5.0×9.0 standoff 127 
						

							Phillips PM2.0×2.0 screw
ColorQuantityLengthThreadHead width
Silver 2 2.0 mm 2.0 mm 4.0 mm
Where used: 2 screws that secure the Bluetooth module to the system board
128 Chapter 7   Screw listing 
						

							Phillips PM2.5×5.0 captive screw
ColorQuantityLengthThreadHead width
Black 3 5.0 mm 2.5 mm 5.0 mm
Where used: 3 screws that secure the fan/heat sink to the computer
Phillips PM2.5×5.0 captive screw 129 
						

							Phillips 2.5×4.0 captive screw
ColorQuantityLengthThreadHead width
Silver 1 4.0 mm 2.5 mm 5.0 mm
Where used: One captive screw (secured by a C-clip) that secures the fan/heat sink assembly to the
system board
130 Chapter 7   Screw listing 
						

							8
Backup and recovery
Recovering system information
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●Backing up your information regularly to protect your important system files.
●Making a set of recovery discs (Recovery Manager software feature). Recovery discs are used to
start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●Creating system restore points (operating system feature). System restore points allow you to reverse
undesirable changes to your computer by restoring the computer to an earlier state.
●Recovering a program or driver (Recovery Manager software feature). This feature helps you reinstall
a program or driver without performing a full system recovery.
●Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition on the hard drive or from recovery discs you
create.
Creating recovery discs
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system and
software to factory settings in case of system instability or failure.
NOTE:Handle these discs carefully and keep them in a safe place. The software allows the creation of
only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R or DVD-R DL (purchased
separately). The discs you use will depend on the type of optical drive installed in your computer.
Because DVDs store more information than CDs, DVDs and DVDs with double-layer (DL) support
reduce the number of discs required.
NOTE:Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
Recovery Manager software.
●The computer must be connected to AC power during this process.
●Only one set of recovery discs can be created per computer.
Recovering system information 131 
						

							●Number each disc before inserting it into the computer optical drive.
●If necessary, you can exit the program before you have finished creating the recovery discs. The next
time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.Click Advanced Options.
NOTE:If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
3.Click Recovery disc creation, and then click Next.
4.Follow the on-screen instructions.
Backing up your information
When to back up
●On a regularly scheduled basis
NOTE:Set reminders to back up your information periodically.
●Before the computer is repaired or restored
●Before you add or modify hardware or software
Backup suggestions
●Create a set of recovery discs using Recovery Manager.
●Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●Store personal files in the Documents folder and back up these folders periodically.
●Back up templates stored in their associated programs.
●Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document, follow these steps:
a.Display the screen.
b.Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.Open a word-processing document, and then select Edit > Paste.
132 Chapter 8   Backup and recovery