HP Pavilion Dv6700 Entertainment Notebook Pc Series Service Guide

Computer feet
DescriptionSpare part number
Rubber Kit (includes base enclosure rubber feet and display bezel screw covers) 431430-001
The computer feet are adhesive-backed rubber pads. The feet attach to the base enclosure in the locations
illustrated below.
Memory module
DescriptionSpare part number
2048-MB (PC2-5300, 667-MHz, DDR2)453774-001 and
457437–001
1024-MB (PC2-5300, 667-MHz, DDR2)446495-001
512-MB (PC2-5300, 667-MHz, DDR2) 446494-001
Before removing the memory module, follow these steps:...

3.Lift the left side of the cover (2), swing it to the right, and remove the cover. The memory/WLAN
module compartment cover is included in the Plastics Kit, spare part number 438368-001.
4.Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
5.Remove the module (2) by pulling it away from the slot at an angle.
NOTE:Memory modules are designed with a notch (3) to prevent incorrect...

RTC battery
NOTE:Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords
and CMOS settings to be cleared.
DescriptionSpare part number
RTC battery (includes 2-sided tape) 446518-001 and
449729-001
Before removing the RTC battery, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the...

WLAN module
DescriptionSpare part number
Intel 802.11a/b/g/n WLAN modules:
●For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam
441086-001
●For use in Austria, Azerbaijan, Bahrain, Belgium,...

DescriptionSpare part number
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the Peoples Republic of China,
Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea,...

3.Remove the WLAN module (4) by pulling it away from the slot at an angle.
NOTE:WLAN modules are designed with a notch (5) to prevent incorrect installation into the
WLAN module slot.
Reverse this procedure to install a WLAN module.
58 Chapter 4   Removal and replacement procedures 

Optical drive
NOTE:All optical drive spare part kits include an optical drive bezel.
DescriptionSpare part number
For use in computer models with Intel processors: 
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer (DL) support462453-001
HD-ROM Drive446502-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe446501-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive446500-001
DVD/CD-RW Combo Drive446499-001
For use in computer models with AMD processors: 
CD-RW and...

4.Use the disc tray frame to slide the optical drive (3) out of the computer.
5.If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
6.Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
7.Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.
60 Chapter 4   Removal and replacement procedures 

Switch cover
DescriptionSpare part number
Switch cover (includes LED board and cable) 446512-001
Before removing the switch cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter...

4.Lift the rear edge of the switch cover and swing it forward until it rests on the keyboard.
5.Release the zero insertion force (ZIF) connector (1) to which the power button board is connected,
and disconnect the cable from the power button board.
6.Disconnect the microphone cable (2) from the power button board.
7.Release the ZIF connector (3) to which the LED board is connected and disconnect the cable from
the power button board.
8.Remove the switch cover.
Reverse this procedure to install the switch...