HP Pavilion Dv6 1100 Entertainment Notebook Pc Series Manual

							6.
Lift the rear edge (1) of the keyboard, and then slide the keyboard (2) back until the keyboard
cable is accessible.
7.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
then disconnect the keyboard cable (2) from the system board.
8.Remove the keyboard.
Reverse this procedure to install the keyboard.
Component replacement procedures
73 
						

							Top cover
NOTE:The top cover spare part kit includes the TouchPad and TouchPad button board, but does not
include the TouchPad cable or TouchPad button board cable. The TouchPad cable and TouchPad
button board cable are included in the Cable Kit, spare part number 640422-001.
DescriptionSpare part number
In butter gold finish641497-001
In dark umber finish640463-001
In espresso black finish640458-001
In linen white finish640460-001
In Pacific blue finish641494-001
In pearl pink finish641496-001
In ruby red finish640461-001
In Sonoma red finish641495-001
In steel gray finish650802-001
Before removing the top cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 59), and then remove the following components:
●
Optical drive (see 
Optical drive on page 60)
●
Hard drive (see 
Hard drive on page 62)
●
Keyboard (see 
Keyboard on page 70)
NOTE:When replacing the top cover, be sure that the power button board and cable (see Power
button board on page 77) and fingerprint reader board and cable (see Fingerprint reader board
on page 78) are removed from the defective top cover and installed on the replacement top cover.
Remove the top cover:
1.Close the computer.
2.Turn the computer upside down, with the front toward you.
74 Chapter 4   Removal and replacement procedures 
						

							3.
Remove the seven Phillips PM2.5×10.0 screws that secure the top cover to the computer.
4.Remove the following screws that secure the top cover to the computer:
●
Three Phillips PM2.0×3.0 screws (1) in the optical drive bay
●
Three Phillips PM2.5×6.0 screws (2)
●
One Phillips PM2.0×4.0 screw (3) in the hard drive bay
5.
Turn the computer right-side up, with the front toward you.
6.Open the computer.
Component replacement procedures
75 
						

							7.
Release the ZIF connectors to which the following cables are attached, and then disconnect the
cables from the system board:
NOTE:The power button board cable, TouchPad button board cable, and fingerprint reader
board cable are included in the Cable Kit, spare part number 640422-001.
●
Power button board cable (1)
●
TouchPad button board cable (2)
●
Fingerprint reader board cable (3) (select models only)
8.Remove the seven Phillips PM2.5×6.0 screws that secure the top cover to the computer.
9.Lift the rear edge of the top cover (1) until the left and right sides disengage from the
base enclosure.
76 Chapter 4   Removal and replacement procedures 
						

							10.
Remove the top cover (2).
Reverse this procedure to install the top cover.
Power button board
DescriptionSpare part number
Power button board (does not include cable)
NOTE:The power button board cable is not included in the power button board spare part kit. The
power button board cable is included in the Cable Kit, spare part number 640422-001.640439-001
Before removing the power button board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 59), and then remove the following components:
●
Optical drive (see 
Optical drive on page 60)
●
Hard drive (see 
Hard drive on page 62)
●
Keyboard (see 
Keyboard on page 70)
●
Top cover (see 
Top cover on page 74)
Remove the power button board:
1.Turn the top cover upside down, with the front toward you.
2.
Release the power button board cable from the clip (1) built into the top cover.
Component replacement procedures
77 
						

							3.
Remove the three Phillips PM2.0×4.0 screws (2) that secure the power button board to the
top cover.
4.Remove the power button board and cable (3).
Reverse this procedure to install the power button board and cable.
Fingerprint reader board
DescriptionSpare part number
Fingerprint reader board (select models only, includes bracket, but does not include cable)
NOTE:The fingerprint reader board cable is not included in the fingerprint reader board spare
part kit. The fingerprint reader board cable is included in the Cable Kit, spare part number
640422-001.640427-001
Before removing the fingerprint reader board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 59), and then remove the following components:
●
Optical drive (see 
Optical drive on page 60)
●
Hard drive (see 
Hard drive on page 62)
78 Chapter 4   Removal and replacement procedures 
						

							●
Keyboard (see Keyboard on page 70)
●
Top cover (see 
Top cover on page 74)
Remove the fingerprint reader board and cable:
1.Turn the top cover upside down, with the front toward you.
2.Release the fingerprint reader board cable (1) from the clips (2) built into the top cover.
3.Remove the two Phillips PM2.0×4.0 screws (3) that secure the fingerprint reader board and
bracket to the top cover.
4.Remove the fingerprint reader board bracket (4) and the fingerprint reader board (5).
Reverse this procedure to install the fingerprint reader board and cable.
Bluetooth module
NOTE:This section applies only to computer models equipped with an Intel processor.
DescriptionSpare part number
EDR v.4.0655792-001
EDR v.3.0537921-001
NOTE:The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is
available in the Cable Kit, spare part number 640422-001.
Component replacement procedures
79 
						

							Before removing the Bluetooth module and cable, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 59), and then remove the following components:
●
Optical drive (see 
Optical drive on page 60)
●
Hard drive (see 
Hard drive on page 62)
●
Keyboard (see 
Keyboard on page 70)
●
Top cover (see 
Top cover on page 74)
Remove the Bluetooth module and cable:
1.Disconnect the Bluetooth module cable (1) from the system board.
2.Release the Bluetooth module cable from the clips (2) and the routing channel built into the front
speaker assembly.
3.
Release the Bluetooth module (3) from the clip built into the front speaker assembly.
4.Remove the Bluetooth module and the Bluetooth module cable.
80 Chapter 4   Removal and replacement procedures 
						

							5.
If it is necessary to replace the Bluetooth module cable, disconnect the cable from the Bluetooth
module and replace it.
Reverse this procedure to install the Bluetooth module and cable.
Component replacement procedures
81 
						

							USB board
DescriptionSpare part number
USB board (does not include cable)
NOTE:The USB board cable is not included in the USB board spare part kit. The USB board cable
is included in the Cable Kit, spare part number 640422-001.640441-001
Before removing the USB board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 59), and then remove the following components:
●
Optical drive (see 
Optical drive on page 60)
●
Hard drive (see 
Hard drive on page 62)
●
Keyboard (see 
Keyboard on page 70)
●
Top cover (see 
Top cover on page 74)
Remove the USB board and cable:
1.Release the ZIF connector to which the USB board cable is connected, and then disconnect the
USB board cable (1) from the system board.
2.Remove the Phillips PM2.5×5.0 screw (2) that secures the USB board to the base enclosure.
3.Remove the USB board (3) and cable.
82 Chapter 4   Removal and replacement procedures