HP Pavilion Dv6 1000 Entertainment Notebook Pc Series Manual

							23.Remove the cable from the clip on the right display hinge (4).
24.If it is necessary to replace the display hinges, remove the four Phillips PM2.5×5.0 screws (1) that
horizontally secure the display hinge bracket to the display panel.
25.Remove the four Phillips PM2.5×5.0 screws (2) that vertically secure the display hinge bracket to
the display panel.
26.Remove the display hinge bracket (3). The Display Hinge Kit is available using spare part number
513477-001 for computers with 15.6-inch displays and 519209-001 for computers with 16-inch
displays.
Component replacement procedures 73 
						

							27.If you need to remove the horizontal bracket from the vertical hinge brackets, remove the two
Phillips PM2.0×5.0 screws (1) that connect the brackets together, and then disconnect the
brackets (2).
NOTE:Steps 28 through 38 provide display assembly internal component removal information
for computers equipped with BrightView display assemblies. See steps 5 through 27 for display
assembly internal component removal information for computers equipped with AntiGlare display
assemblies.
NOTE:See Webcam/microphone moduleon page 49 for webcam/microphone module
replacement instructions for computers equipped with BrightView display assemblies.
28.If it is necessary to replace the display bezel or any of the display assembly internal components,
remove the following screw covers and screws:
(1) Two Mylar screw covers on the display bezel bottom edge. The display rubber screw covers
are included in the Display Rubber Kit, spare part number 512361-001.
(2) Two Phillips PM2.5×6.5 screws.
29.Flex the inside edges of the top edge (1), the left and right sides (2), and the bottom edge of the
display bezel (3) until the bezel disengages from the display enclosure.
74 Chapter 4   Removal and replacement procedures 
						

							30.Remove the display bezel (4). The display bezel is available using spare part number 512359-001
(16-inch display) or 512364-001 (15.6-inch display).
31.If it is necessary to replace the display inverter, disconnect the display inverter from the double-
sided tape securing it to the display, and then release the display inverter (1) as far from the display
enclosure as the display panel cable and backlight cable allow.
32.Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
33.Remove the display inverter. The display inverter is available using spare part number
488317-001.
Component replacement procedures 75 
						

							34.If it is necessary to replace the display panel, remove the two Phillips PM2.5×5.0 screws (1) from
the top corners and the six Phillips PM2.5×5.0 screws (2) from the display hinges.
35.Flex the bottom of the display panel (1) back and release the display hinges. Disconnect the display
LED cable (2) from the display panel cable. Remove the display panel (3). Display panels are
available using spare part numbers 511868-001 (16-inch non-LED display), 570094-001 (16-inch
LED display), 512363-001 (15.6-inch non-LED display), and 570095-001 (15.6-inch LED
display).
36.If it is necessary to replace the display hinges, remove the two Phillips PM2.0×3.0 screws (1) that
secure each display hinge to the display panel.
76 Chapter 4   Removal and replacement procedures 
						

							37.Remove the display hinges (2). The display hinges are available in the Display Hinge Bracket Kit,
spare part 512360-001 (16-inch display) or 512365-001 (15.6-inch display). The display hinge
screws are available in the Display Screw Kit, spare part number 512362-001.
38.If it is necessary to remove the display panel cable, remove the adhesive reinforcement strip (1)
from the display panel cable, and disconnect the display panel cable (2). Remove the tape (3) that
secures the cable to the display panel. The display panel cable is available using spare part number
512825-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures 77 
						

							Speaker
DescriptionSpare part number
Speaker533865-001
Before removing the speaker, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 48).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 57)
b.Optical drive (see 
Optical drive on page 51)
c.Switch cover and keyboard (see 
Switch cover and keyboard on page 63)
d.Display assembly (see 
Display assembly on page 68)
Remove the speaker:
1.Turn the right side up, with the front toward you.
2.Disconnect the speaker cable from the system board (1).
3.Remove the 5 Phillips PM2.5×6.0 screws (2) that secure the speaker to the top cover.
4.Lift the speaker up and off the top cover (3).
Reverse this procedure to install the speaker.
78 Chapter 4   Removal and replacement procedures 
						

							Bluetooth module
NOTE:The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is available using spare part number 489822-001.
DescriptionSpare part number
Bluetooth module483113-001
Before removing the Bluetooth module, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.Remove the battery (see 
Battery on page 48).
5.Remove the switch cover and keyboard (see 
Switch cover and keyboard on page 63).
Remove the Bluetooth module:
1.Disconnect the Bluetooth module cable (1) from the system board.
2.Remove the Phillips PM2.0×3.0 screw (2) that secures the Bluetooth module to the top cover.
3.Remove the Bluetooth module from the top cover (3).
4.Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures 79 
						

							Top cover
DescriptionSpare part number
For use only with white computers equipped with a fingerprint reader518109-001
For use only with white computers not equipped with a fingerprint reader518108-001
For use only with black computers equipped with a fingerprint reader518789-001
For use only with black computers not equipped with a fingerprint reader518788-001
For use only with MTV2 artist edition computers 570206-001
Before removing the top cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 48).
5.Remove the following components:
a.Hard drive (see 
Hard drive on page 57)
b.Optical drive (see 
Optical drive on page 51)
c.Switch cover and keyboard (see 
Switch cover and keyboard on page 63)
d.Display assembly (see 
Display assembly on page 68)
Remove the top cover:
1.Turn the computer upside down, with the front toward you.
2.Remove the 10 Phillips PM2.5×7.0 screws (1) that secure the top cover to the computer.
80 Chapter 4   Removal and replacement procedures 
						

							3.Remove the Phillips PM2.5×4.0 screw (2) that secures the top cover to the computer. This screw
is in the battery bay.
4.Turn the computer right-side up, with the front toward you.
5.Disconnect the following cables from the system board:
(1) TouchPad cable
(2) Fingerprint reader board cable
NOTE:This cable connects to a LIF connector on the system board.
Component replacement procedures 81 
						

							6.Remove the four Phillips PM2.5×4.0 screws that secure the top cover to the computer.
7.Lift the rear edge (1) of the top cover until it rests at an angle.
8.Remove the top cover (2) by lifting it straight up.
Reverse this procedure to install the top cover.
82 Chapter 4   Removal and replacement procedures