HP Pavilion Dv5 1000 Entertainment Notebook Pc Series Manual

Creating recovery discs
NOTE:HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE:Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●You will need high quality CD-R, DVD-R,...

Backing up your information
When to back up
●On a regularly scheduled basis
NOTE:Set reminders to back up your information periodically.
●Before the computer is repaired or restored
●Before you add or modify hardware or software
Backup suggestions
●Create a set of recovery discs using Recovery Manager.
●Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●Store personal files in the Documents folder and back up these folders periodically.
●Back up...

When to create restore points
●Before you add or extensively modify software or hardware
●Periodically, whenever the system is performing optimally
NOTE:If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.Select Start > Control Panel > System and Maintenance > System.
2.In the left pane, click System Protection.
3.Click the System Protection tab.
4.Under Automatic restore points, select the disk for which you want to create a...

Performing a recovery
NOTE:You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state...

9 Connector pin assignments
1394
PinSignal
1Power
2Ground
3TPB-
4TPB+
5TPA-
6 TPA+
Audio-in (microphone)
PinSignal
1Audio signal in
2Audio signal in
3Ground
1394 147 

Audio-out (headphone)
PinSignal
1Audio out, left channel
2Audio out, right channel
3 Ground
External monitor
PinSignal
1Red analog
2Green analog
3Blue analog
4Not connected
5Ground
6Ground analog
7Ground analog
8Ground analog
9+5 VDC
10Ground
11Monitor detect
12DDC 2B data
13Horizontal sync
14Vertical sync
15 DDC 2B clock
148 Chapter 9   Connector pin assignments 

HDMI
PinSignal
1TMDS data 2+
2TMDS data 2 shield
3TMDS data 2–
4TMDS data 1+
5TMDS data 1 shield
6TMDS data 1–
7TMDS data 0+
8TMDS data 0 shield
9TMDS data 0–
10TMDS clock+
11TMDS clock shield
12TMDS clock-
13CEC
14No connect
15DDC clock
16DDC data
17Ground
18+5V power
19Hot plug detect
20 Shell
HDMI 149 

RJ-11 (modem)
PinSignal
1Unused
2Tip
3Ring
4Unused
5Unused
6 Unused
RJ-45 (network)
PinSignal
1Transmit +
2Transmit -
3Receive +
4Unused
5Unused
6Receive -
7Unused
8 Unused
150 Chapter 9   Connector pin assignments 

Universal Serial Bus
PinSignal
1+5 VDC
2Data -
3Data +
4Ground
Universal Serial Bus 151 

10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The...