HP Pavilion Dm1 3100 Entertainment Notebook Pc Series Manual

							Keyboard
NOTE:The keyboard spare part kit includes a keyboard cable.
DescriptionSpare part number
For use in Belgium635318-A41
For use in Brazil635318-201
For use in the Czech Republic 635318-221
For use in France635318-051
For use in French Canada635318-121
For use in Germany635318-041
For use in Greece608583-DJ1
For use in Hungary635318-211
For use in Israel608583-BB1
For use in Italy635318-061
For use in Japan635318-291
For use in Korea635318-AD1
For use in Latin America6355318-161
For use in Norway635318-DH1
For use in Portugal635318-131
For use in Russia635318-251
For use in Saudi Arabia635318-171
For use in Spain635318-071
For use in Switzerland635318-BG1
For use in Taiwan635318-AB1
For use in Thailand635318-281
For use in Turkey635318-141
For use in the United Kingdom 635318-031
For use in the United States635318-001
Before removing the keyboard, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
ENWW Component replacement procedures 43 
						

							4.Remove the battery (see Battery on page 32).
5.Remove the service cover (see 
Hard drive / Solid state drive on page 33).
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
Removing the keyboard:
To remove the keyboard, follow these steps:
1.Position the computer upside down on a flat surface, with the rear toward you.
2.Remove the 3 screws that secure the keyboard to the computer.
3.Position the computer display-side up, with the front toward you.
4.Open the computer as far as possible.
5.Use a flat-bladed screwdriver to pry the rear edge of the keyboard (1) loose from the three
retaining tabs.
6.Lift the keyboard (2) and turn it upside down, resting it on the top cover.
44 Chapter 4   Removal and replacement procedures ENWW 
						

							7.Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
then disconnect the keyboard cable (2) from the system board.
8.Remove the keyboard.
Reverse this procedure to install the keyboard.
ENWW Component replacement procedures 45 
						

							Top cover
DescriptionSpare part number
Top cover635316-001
Before removing the top cover, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
5.Remove the service cover 
Hard drive / Solid state drive on page 33.
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
7.Remove the keyboard (see 
Keyboard on page 43).
Remove the top cover:
To remove the top cover, follow these steps:
1.Position the computer upside down on a flat surface, with the front toward you.
2.Use a thin, flat tool to release the 2 rubber feet, and then remove the two screws that are located
under the rubber feet (1).
3.Remove the remaining 8 screws that secure the keyboard to the computer.
4.Position the computer right-side up, with the front toward you and the display open as far as
possible.
5.Lift the rear edge (1) of the top cover until it detaches from the base enclosure.
46 Chapter 4   Removal and replacement procedures ENWW 
						

							6.Remove the top cover (2) by lifting it straight up.
Reverse this procedure to install the top cover.
Power button board
DescriptionSpare part number
Power button board (includes cable) 636448-001
Before removing the power button board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
5.Remove the service cover (see 
Hard drive / Solid state drive on page 33).
6.Remove the keyboard (see 
Keyboard on page 43).
7.Remove the top cover (see 
Top cover on page 46).
Before removing the power button board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
ENWW Component replacement procedures 47 
						

							5.Remove the service cover (see WLAN module on page 39).
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
7.Remove the keyboard (see 
Keyboard on page 43).
8.Remove the top cover (see 
Top cover on page 46).
Remove the power button board:
To remove the power button board, follow these steps:
1.Position the top cover upside down, with the front toward you.
2.Remove the screw (1) that secures the power button board to the top cover.
3.Lift up and remove the power button board (2).
Reverse this procedure to install the power button board.
TouchPad button board
DescriptionSpare part number
TouchPad button board (includes bracket and cable) 636449-001
 
Before removing the TouchPad button board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
48 Chapter 4   Removal and replacement procedures ENWW 
						

							3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
5.Remove the service cover (see 
WLAN module on page 39).
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
7.Remove the keyboard (see 
Keyboard on page 43).
8.Remove the top cover (see 
Top cover on page 46).
NOTE:Before removing the TouchPad, it is necessary to remove the TouchPad button board
bracket.
Remove the TouchPad button board bracket:
To remove the TouchPad button board bracket, follow these steps:
1.Position the top cover upside down, with the front toward you.
2.Remove the four screws that secure the TouchPad button board bracket to the top cover (1).
3.Lift up and remove the TouchPad button board bracket (2).
Reverse this procedure to install the TouchPad button board bracket.
Remove the TouchPad button board:
To remove the TouchPad button board, follow these steps:
1.Remove the 2 screws that secure the TouchPad button board to the top cover (1).
2.Lift up and remove the TouchPad button board (2).
ENWW Component replacement procedures 49 
						

							Reverse this procedure to install the TouchPad button board.
Speaker assembly
DescriptionSpare part number
Speakers (include cables)635313-001
Before removing the speaker assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
5.Remove the service cover (see 
Hard drive / Solid state drive on page 33).
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
7.Remove the keyboard (see 
Keyboard on page 43).
8.Remove the top cover (see 
Top cover on page 46).
Remove the speaker assembly:
To remove the speaker assembly, follow these steps:
1.Position the top cover upside down with the front toward you.
2.Remove the 2 screws that secure the speaker assembly to the top cover (1).
50 Chapter 4   Removal and replacement procedures ENWW 
						

							3.Lift up and remove the speaker assembly(2).
Reverse this procedure to install the speaker assembly.
ENWW Component replacement procedures 51 
						

							Display assembly
DescriptionSpare part number
29.5-cm (11.6-in) (1366 × 768) HD BrightView LED display assembly (includes webcam,
microphone, nameplate, and logo)635308-001
Verizon 29.5-cm (11.6-in) (1366 × 768) HD BrightView LED display assembly (includes
webcam, microphone, nameplate, and logo)639610-001
Before removing the display assembly, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation mode,
turn on the computer, and then shut it down using the operating system.
2.Disconnect all of the external devices that are connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the battery (see 
Battery on page 32).
5.Remove the service cover (see 
Hard drive / Solid state drive on page 33).
6.Remove the hard drive (see 
Hard drive / Solid state drive on page 33).
7.Disconnect the wireless antenna cables from the WLAN module (see 
WLAN module
on page 39) and WWAN module (see WWAN module on page 37).
8.Remove the keyboard (see 
Keyboard on page 43).
9.Remove the top cover (see 
Top cover on page 46).
Remove the display assembly:
1.Position the computer display-side up, with the front toward you.
2.Open the computer as far as possible.
3.Disconnect the display panel cable (1) from the system board.
52 Chapter 4   Removal and replacement procedures ENWW