HP Pavilion Dm1 1000 Entertainment Notebook Pc Series Manual

							Display components
Component Description
(1)Internal display switchTurns off the display if the display is closed while the
power is on.
(2)Webcam lightOn: The webcam is in use.
(3)WebcamCaptures still photographs and videos.
NOTE:To capture videos, you must install additional
webcam software.
(4)Internal microphone Records sound.
Identifying the hardware 11 
						

							Bottom components
Component Description
(1)Battery release latches (2)Release the battery from the battery bay.
(2) Battery bayHolds the battery.
(3) Vents (4) Enable airflow to cool internal components.
NOTE:The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)Hard  drive  bay Contains the hard drive, the wireless LAN module slot, and
the memory module slot.
CAUTION:To prevent an unresponsive system, replace
the wireless module only with a wireless module authorized
for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact technical support through Help and Support.
12 Chapter 2   Hardware features 
						

							Wireless antennas
Component Description
(1)WLAN antennas (2)*Send and receive wireless signals to communicate with wireless
local area networks (WLANs).
(2)WWAN antennas (2) (select models only)*Send and receive wireless signals to communicate with wireless
wide-area networks (WWANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These notices are located in Help and Support.
Identifying the hardware 13 
						

							Additional hardware components
Component Description
(1)Power cord*Connects an AC adapter to an AC outlet.
(2)Battery*Powers the computer when the computer is not plugged into
external power.
(3)AC adapterConverts AC power to DC power.
*Batteries and power cords vary in appearance by country or region.
14 Chapter 2   Hardware features 
						

							Identifying the labels
The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.
●Service tag—Provides important information including the following:
◦Product name (1). This is the product name affixed to the front of your computer.
◦Serial number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
◦Part Number/Product number (p/n) (3). This number provides specific information about the
hardware components of the product. The part number helps a service technician to determine
what components and parts are needed.
◦Model description (4). This is the alphanumeric identifier you use to locate documents, drivers,
and support for your computer.
◦Warranty period (5). This number describes the duration (in years) of the warranty period for
this computer.
Have this information available when you contact technical support. The service tag label is affixed
to the bottom of the computer.
●Microsoft
® Certificate of Authenticity—Contains the Windows® Product Key. You may need the
Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom
of the computer.
●Regulatory label—Provides regulatory information about the computer, including the following:
◦Information about optional wireless devices and the approval markings of some of the
countries or regions in which the devices have been approved for use. An optional device may
be a wireless local area network (WLAN) device. You may need this information when
traveling internationally.
◦The serial number of your HP Mobile Broadband Module.
The regulatory label is affixed inside the battery bay.
Identifying the labels 15 
						

							3 Wireless and local area network
Using wireless devices
Wireless technology transfers data across radio waves instead of wires. Your computer may be
equipped with one or more of the following wireless devices:
●Wireless local area network (WLAN) device—Connects the computer to wireless local area
networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices,
your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access
point.
●HP Mobile Broadband Module—A wireless wide area network (WWAN) device that provides
access to information wherever mobile network operator service is available. In a WWAN, each
mobile device communicates to a mobile network operator’s base station. Mobile network operators
install networks of base stations (similar to cell phone towers) throughout large geographic areas,
effectively providing coverage across entire states, regions, or even countries.
●Bluetooth
® device—Creates a personal area network (PAN) to connect to other Bluetooth-enabled
devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each
device communicates directly with other devices, and devices must be relatively close together—
typically within 10 meters (approximately 33 feet) of each other.
Computers with WLAN devices support one or more of the following IEEE industry standards:
●802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a
frequency of 2.4 GHz.
●802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An 802.11g
WLAN device is backward compatible with 802.11b devices, so they can operate on the same
network.
●802.11a supports data rates of up to 54 Mbps and operates at a frequency of 5 GHz.
NOTE:802.11a is not compatible with 802.11b and 802.11g.
●802.11n supports data rates of up to 450 Mbps and may operate at 2.4 GHz or 5 GHz, making it
backward compatible with 802.11a, b, and g.
For more information on wireless technology, refer to the information and Web site links provided in
Help and Support.
16 Chapter 3   Wireless and local area network 
						

							Identifying wireless and network status icons
IconNameDescription
Wireless (connected)Identifies the location of the wireless lights and the wireless
buttons on the computer. Also identifies the HP Wireless
Assistant software on the computer and indicates that one or
more of the wireless devices are on.
Wireless (disconnected)Identifies the HP Wireless Assistant software on the
computer and indicates that all of the wireless devices are
off.
HP Connection ManagerOpens HP Connection Manager, which enables you to create
a connection with an HP Mobile Broadband device (select
models only).
Wired network (connected)Indicates that one or more network drivers are installed, and
one or more network devices are connected to a wired
network.
Wired network (disabled/disconnected)Indicates that one or more network drivers are installed, but
no network devices are connected (or all network devices are
disabled in Windows
® Control Panel).
Network (connected)Indicates that one or more network drivers are installed, and
one or more network devices are connected to a wireless
network.
Network (disconnected)Indicates that one or more network drivers are installed and
wireless connections are available, but no network devices
are connected to a wireless network.
Network (disabled/disconnected) Indicates that one or more network drivers are installed, but
no wireless connections are available (or all wireless network
devices are disabled by the wireless button or HP Wireless
Assistant).
Using the wireless controls
You can control the wireless devices in your computer using these features:
●Wireless button or wireless switch
●Wireless Assistant software (select models only)
●HP Connection Manager software (select models only)
●Operating system controls
Using wireless devices 17 
						

							Using the wireless button
The computer has a wireless button, one or more wireless devices, and one or two wireless lights,
depending on the model. All of the wireless devices on your computer are enabled at the factory, so the
wireless light is on (blue) when you turn on the computer.
The wireless light indicates the overall power state of your wireless devices, not the status of individual
devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is off, all
wireless devices are off.
NOTE:On some models, the wireless light is amber when all wireless devices are off.
Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or
turn off the wireless devices simultaneously. Individual wireless devices can be controlled through
Wireless Assistant software (select models only).
Using Wireless Assistant software (select models only)
A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is
disabled in Setup Utility, it must be reenabled in Setup Utility before it can be turned on or off using
Wireless Assistant.
NOTE:Enabling or turning on a wireless device does not automatically connect the computer to a
network or a Bluetooth-enabled device.
To view the state of the wireless devices, click the Show hidden icons  icon, the arrow at the left of the
notification area, and position the mouse pointer over the wireless icon.
If the wireless icon is not displayed in the notification area, complete the following steps to change
Wireless Assistant properties:
1.Select Start > Control Panel > Hardware and Sound > Windows Mobility Center.
2.Click the wireless icon in the Wireless Assistant tile, which is located in the bottom row of
Windows
® Mobility Center.
3.Click Properties.
4.Select the check box next to HP Wireless Assistant icon in notification area.
5.Click Apply.
6.Click Close.
For more information, refer to the Wireless Assistant software Help:
1.Open Wireless Assistant by clicking the wireless icon in Windows Mobility Center.
2.Click the Help button.
18 Chapter 3   Wireless and local area network 
						

							Using HP Connection Manager (select models only)
You can use HP Connection Manager to connect to WWANs using the HP Mobile Broadband device in
your computer (select models only).
To start Connection Manager, click the Connection Manager icon in the notification area, at the far
right of the taskbar.
– or –
Select Start > All Programs > HP Connection Manager > HP Connection Manager.
For more details about using Connection Manager, refer to the Connection Manager software Help.
Using operating system controls
Some operating systems also offer a way to manage integrated wireless devices and the wireless
connection. For example, Windows provides the Network and Sharing Center that allows you to set up
a connection or network, connect to a network, manage wireless networks, and diagnose and repair
network problems.
To access the Network and Sharing Center, select Start > Control Panel > Network and Internet >
Network and Sharing Center.
For more information, select Start > Help and Support.
Using wireless devices 19 
						

							Using a WLAN
With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other
devices and accessories that are linked by a wireless router or a wireless access point.
NOTE:The terms wireless router and wireless access point are often used interchangeably.
●A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points
that can accommodate a large number of devices and accessories and can separate critical
network functions.
●A home or small office WLAN typically uses a wireless router, which allows several wireless and
wired computers to share an Internet connection, a printer, and files without requiring additional
pieces of hardware or software.
To use the WLAN device in your computer, you must connect to a WLAN infrastructure (provided through
a service provider or a public or corporate network).
Setting up a WLAN
To set up a WLAN and connect to the Internet, you need the following equipment:
●A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an
Internet service provider (ISP)
●A wireless router (purchased separately) (2)
●The computer, equipped with a wireless device (3)
The illustration below shows an example of a wireless network installation that is connected to the
Internet.
As your network grows, additional wireless and wired computers can be connected to the network to
access the Internet.
For help in setting up your WLAN, refer to the information provided by your router manufacturer or your
ISP.
20 Chapter 3   Wireless and local area network