HP Mp3220 Digital Projector Users Guide

User’s Guide41
Adjusting the Projector
Tint Shifts colors toward red or green.
Red Adjusts the amount of red in the picture.
Green Adjusts the amount of green in the picture.
Blue Adjusts the amount of blue in the picture.
Color space For certain component inputs, selects the type of 
signal encoding used by the input source. You can 
override the selection made by the projector.
Reset color settings Resets these color settings to their default settings.
Shape settings... Adjusts the shape of the...

42User’s Guide
Adjusting the Projector
Setup menu
Help menu
Setup
Language... Selects the language for the menus.
Lamp saver Sets a lower power level for the lamp.
Projector position Adjusts the image to match the orientation of the 
projector: upright or upside-down, in front of or 
behind the screen. Inverts or reverses the image 
accordingly.
Timeout for menu Sets how many seconds the on-screen menu waits for 
input before it closes.
Auto-scan sources Sets whether the projector automatically searches...

User’s Guide43
4
Maintaining the Projector
This chapter explains how to maintain the projector.
■“Performing Routine Maintenance” on page 43
■“Upgrading the Projector” on page 47
Performing Routine Maintenance
This section provides instructions on performing routing maintenance.
■“To get the projector status” on page 43
■“To clean the projector lens” on page 44
■“To replace the lamp module” on page 44
■“To replace the battery in the remote control” on page 46
To get the projector status
■Open the...

44User’s Guide
Maintaining the Projector
To clean the projector lens
■To minimize the risk of damaging or scratching the lens surface, blow dust 
particles off the lens with clean, dry, deionized air.
If this method does not work, use the following method:
■Wipe the lens in a single direction with a clean, dry cloth. Do not wipe back and 
forth across the lens.
If the cloth is dirty or smears the lens, wash the cloth. If the cloth is still dirty after 
washing it or the fabric is damaged, replace it....

User’s Guide45
Maintaining the Projector
1. Turn off the projector and allow it to cool for 30 minutes.
2. On the bottom of the projector, loosen the two screws on the lamp cover and 
remove the cover.
3. Loosen the two screws on the lamp module and pull out the module.
4. Insert the lamp module and tighten the two screws.
5. Install the cover and tighten the two screws.
6. Turn on the projector. If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp again.
7. Open the...

46User’s Guide
Maintaining the Projector
To replace the battery in the remote control
1. Pull out the battery holder.
2. Insert the new battery in the holder.
3. Push the holder into the remote control.
When discarding old batteries, contact your local waste-disposal provider regarding 
local restrictions on the disposal or recycling of batteries.
1
23 

User’s Guide47
Maintaining the Projector
Upgrading the Projector
To update the firmware
HP might periodically release updated versions of the projector firmware to enhance 
the projector performance. The projector firmware version is shown in the on-screen 
menu at Help. Check for updated versions at http://www.hp.com/go/proj_firmware.
USB method
1. On a computer with a USB port, go to the HP projector upgrade website (see 
introduction for this section) and download the latest file intended for a USB...

48User’s Guide
Maintaining the Projector 

User’s Guide49
5
Installing Permanently
This chapter explains how to permanently install the digital projector. 
Installing the Projector
This section provides instructions on how to permanently install the projector.
■“To install on a table” on page 49
■“To install on the ceiling” on page 50
■“To install for rear projection” on page 52
■“To mount the projector on a tripod” on page 53
■“To lock the projector” on page 53
To install on a table
This installation is covered in detail in Chapter 1. See...

50User’s Guide
Installing Permanently
To install on the ceiling
ÅWAR N I N G: To minimize the risk of injury from improperly installed equipment, it 
is recommended that a professional installer performs the ceiling installation.
✎The actual projector and mounting plate differ from those shown below, but the steps 
are the same.
1. Attach the mounting plate to the bottom of the projector. The pointed part of the 
hole in the bracket faces the back of the projector. See the instructions that came 
with...